ITs not boosting as you don't spend any time on boost.. - more power

I came here for the bras😂 i gotta an mg thought 👍

Hi Cleo, where did you get the hub from?

Where did you get your sunstrip from?

Hi, have you put wider wheel arches on the car, and if so where can you buy them from, Cheers.

❤

Rx8 kit 🔥

Good job 👏

That poor camera angle, I have no idea what I am watching

Great video! Very clear instructions!

Hello, great informative vid… The short earth horn cable that you added an extension to. Where was it located after you pulled out the horn? Do I have to pull out the clock spring to find it? I’m about to do same swap as well. Keep up the great work! NYC

NIce video Cleo ... Pos & Neg can go any way round on a switch by the way :)

Just wondering, if you had the thermal liner in when you tested it out ?

Absolutely brilliant, we once had 150,000 of these in the uk. Lets hope they recolonise everywhere.

Tried to find a Cayman in my budget and wound up with a 2006 BMW e90 330i. Caymans just didn't fit my price range. We'll see what things look like in a few years.

cute, but cars are a MANS domain......

Love do you have any info how to open this tent manually ???? Thank you for responding

Thanks for the ONLY proper video I’ve seen so far showing how this is done. You could have made your own horn ground jumper cable with just a bit of regular wire to save yourself a few bucks.

Hello 😊 thank you for great video… where do you plug in the resistors please? I can’t work out where they plug in.. I’ve tried a couple of ways but no luck 😢 there is two wires from air bag…

🍺🤯👍🏽👊🏽😎👍🏽💯

I don't suppose you still have that 3 spoke available do you?! Finding an all black wheel without on wheel function buttons is nigh impossible! Great video by the way!

Have you got an update on this?

Grate video

Hey, realize it has been a minute but is there any way you could tell me what the thread pattern is in the three bolts used to pull the dampener are. The (3) bolts that go through the disc part of the tool and thread into the actual dampener to,pull it as you screw in the bolt that applies tension to the crank. Is this clear enough? Thanks in advance!

Very nice set up 😊

🎉❤🎉❤🎉❤💪🏿👍🏾🌹

What happened to you Cleo? Hope you are okay? Anymore videos coming?

Ooopsie...possible wrong camber stance

National Treasure. Yeah, you.

That roof tent doesn’t weigh enough to matter

Why did u not run éngin so we could here noise b4 work.

You saved my life! I replaced the idle pulley and finally that tedious noise disappeared magically ❤️

Hi Will I be able to use this tool to remove the flange from the Bmw F30 gearbox? thanks

Oh hey I wonder if this is the noise my mini is maki- HOLY HELL WHAT IS THAT A K&N INTERCOOLER?!

How hard would it have been to share the noise so others can compare 🤨

Great video Cleo. I was wanting to know where did u get the grill and foglight ducks.

was it squeaking as well or only whistling? i can’t figure out if i need to change my idler pulley, the belt, or the tensioner

where have you got too

resistor 2.2 on the black connector and the green connector?

Your mini sounds exactly the same as mine, i think it was high intake air temps reducing power they do heat soak even with bigger intercooler

Realistic expectations for most MGB's here and so nice to see from this un biased restoration. I have owned several of these and seen a lot more. I would say that most of the listings on Ebay will not be much better; probably all nice and shiny though. These cars are soooooooo easy to botch up and sell on. Proper restoration is very expensive and some may even be on their second "rebuild" by now. £600 sounds ok for the car you bought and you could possibly have shelled out £10,000 for an un-documented "rebuilt" example of similar quality. Will enjoy seeing how you get on, sounds very interesting.

Suggestion for anyone else doing this job... Replace the rubber bushings in the belt tensioner with Powerflex urethane bushings. I put a new OEM tensioner on mine and within 8k miles, one of the rubber bushings disintegrated. BTW, The new OEM bolt already had thread locker pre-applied. No need for additional thread locker.

Do you need to raise the motor or no ? cause on lot of video i see people raising motor

@Cleo @Cars and Bras, i also have a R53. What extra cooling mods do you have for when you are on track? Like oil or transmission oil cooler?

Wow that looks like fun!

Well done with your noise diagnosis and repair, the idler was replaced on my R53 and noise gone 😊

great to see you back again

I changed the belt tensioner pulley on my sisters mini.. that one you can loosen with the thumb tab and clip it off to where it stays loose. Then i turned the car on and no noise, pressed the pulley against the band and got the noise again. Thats how i figured it wasnt thenwater pump ir any other pulley.. took me about an hourto do it and changed the belt out also because it was worn..

How about suspension upgrades? Are you not going to need a GT3 (or other) control arm to keep from wearing out your tires prematurely?

What's the wheels and tires specs? I can see they are rpf1 but can't tell if that's a 16 or 17 inch? And what size are the tires? It looks absolutely bad ass