send program file

You are actually a engineer

what is the input outpu range of this converter and what is the maximum current

👍

Wonderful 👍

Great work

Why 3 relay used in u r pcb What is function

I don't know charging side which frequency used Inverter side 15kHz spwm switching frequency seeing iam amaron Inverter Why all Comercial Inverters are used 0 7 v ac 0 220

Can you share the circuit diagram?

Great job, how about the circuit diagram?

Need this model HEX code

Wonderful work Sir Please can this program work in Atmega328

Please continue. I am a veteran, but in search of inspiration. You make most useful and interesting projects.

You have a very nice calligraphy!

I recently came across a circuit with a parallel coil, which allows for easy buck and boost conversion, with a N-channel MOSFET, or 2, for active switching rather than using a diode.

স্যার, আমি আপনার একজন ফ্যান। আপনার ভিডিও গুলো অনেক তথ্যবহুল ও নির্ভরযোগ্য। আপনাকে অসংখ্য ধন্যবাদ, এত সুন্দর করে আমাদের সাথে শেয়ার করার জন্য। আশাকরি আপনার এই ভিডিও থেকে আমরা অনেকেই অনেক কিছু শিখতে পারবো। আপনার অনাগত দিনগুলো সুন্দর হোক, এটাই প্রত্যাশা। ভাল থাকবেন প্রিয় মানুষ, শুভ কামনা সবসময়।

Great tutorial. Thanks ❤

You are a real engineer man 😊

❤

Hi sir, thanks for the video, please make a video of static transfer switch using thyristors.

Vary good sir. Possible contact number

This channel is the best 🎉🎉😊

Very nice video 🎉🎉😊

Awesome channel we need more videos 😭😭😭😭😔

We need to come back 😭😔 Awesome channel 💯💯 thanks for everything 🎉🎉

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤ 🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩

where did you get that Teseract at the end of the video?

Brother! what is Thiasotiks?

❤❤❤

It's very helpful.... ❤

Nice project sir..... thanks for sharing ❤

Hi, Can this circuit be used for mains voltages, say 240V ac mains input fuse replacement.

Thank you for the video. I tried to rebluid this experience with P-mosfet , but I get always 12v in outpout of buck, because the gat p mosfet is always open in this configuration. please can you explain and tell me what i have to do to siolve this problem.

Love your efforts made on this reverse engineering ❤❤❤

Will you be adding feedback to stabilize output voltage

Is code are complete for charging and changeover function

Very nice work. I have a question. To convert a square weave inverter in to sine wave inverter , only changing firmware is sufficient or we have to change transformer also.

vc e muito bom na programação vc conseguiria fazer SPLL para sincronismos de inversor com rede elétrica

Looking forward for more informative tutorials. Regards 🙏

Nice watching your video would help me learn a lot. Regards 🙏

thanks

Good to know you are also fan Sam Benyaakov's fan. He is THE BEST! I am guessing the gate driver is getting burnt because of long wires on the perf board. Schematic wise I didn't find anything wrong. However, C26 for Bootstrapping looks quite overkill and also little more capacitance at the VCC pin (Parallel to the C27) would be nicer. Diagnostic of a circuit on perf board is quite difficult task as you can't take all the parasitic in account. Only part that I didn't like is the steering of the voltage loop via PWM DAC and D4. I would use a summing amp instead. Another problem with synchronous buck in this plan is when duty cycle is low and its running in DCM. The LO side MOSFET will discharge the battery instead of charging.

ADC reading equivalent to maximum chg current during full charge = ((ic * a) / ADC res); For example. ic = 0.5 A, actual voltage amplification. a = 0.22, ADC resolution = 4.887 mV, please explain where these numbers come from.

Hello, may I ask? In the diagram, pin D3 in the arduino is specifically the +VE_CY pin. If I don't use this pin, will it affect the operation of the circuit? And the next question I want to ask is how to measure the charging current of the battery, when the shunt resistor has been used to measure the overload. I do not use the CHNG-OVG-RLY pin, but only the CHG-RLY pin (relay switching between inverter and grid). Is that possible, sir?

YOU REALLY STUDIED AVR CHIPS. THIS IS FACTUAL!

Excuse me sir I want to modify it with a 4 wire fan, can I modify the program for example the fan speed depends on the temperature reading of the lm35 with the pwm output which controls the fan and there are remaining atmega pins there are D0 or TX can I add a fan rotation failure feature by reading the tachometer pin on the fan 4 cables, whether the atmega memory is not remaining or the sine pwm generation function will be disrupted

hello, i'm has read your code for this vidio, in your code the lookup table make with matlab, how to make the lookup tabel with matlab ? can you help me sir ? thanks

could u please do bldc motor driver based on arduino? there are alots on utube ,but they are speed fast by varible resistor ,also they could not explain what the best signal for bldc motor ,is it spwm what u use it in the inverter or the six steps bldc signals esc drivere that on the market?

hello, can you share circiut diagram

দাদা এটার .ino file হবে???