Drink every time he says "Flange"

How do you clean the lava rock? I assume you replace it yearly since it can't be cleaned?

I did not understand what was fixed. It seemed like it was taken apart and then put back the same way it was. Would appreciate clarification. Part of the explanation sounded like the problem with the previous installation was that the ring had been placed on the flange and then the bowl had been pressed on it, rather than putting in on the bowl and then pressing the bowl and ring on the flange. The video insists that the correct way is to put it on the bowl, but then does it the other way. I personally do not think it makes a difference, except that if one puts it on the bowl it may drop when the bowl is lifted.

What to do if remover took out and didn’t document the disconnect?

MINE HAS A GRAY WIRE ,I DID NOT SEE ONE ON YOUR SWITCH, AND MINE HAS A LIGHT,THE GRAY WIRE WAS HANGING LOOSE WHEN I TOOK IT APART, I ONLY HAD ONE SPEED,I HOKED IT TO 2 OTHER GRAY WIRES NOTHING CHANGED.DO ALL WIRES FROME THE SWITCH RECONNECT TO THE SAME COLORS OF THE FAN?

Not a professional but suspect the real reason there was an issue is that the top of the toilet flange is below the level of the finished tile. The wax should make contact with both the flange and the underside of the toilet porcelain. You probably need a few shims/ extenders on the toilet flange.

I have different color wires then you black purple yellow and pink wear do they go I have same replacement switch

The grill tents are to stop fats dripping into the burner holes and lava rock alone wont do this .. keep the protective cover’s on it works the same without blocking any burner holes !

If you implement heat mat on top of grill. You will not have any issues with flair ups, and less grease contacting lava rocks! Personally I never cared for the rocks!

GREAT video and easy to understand. Thanks! I DID document which wires go to which numbers but I have misplaced that paper. If I cannot find it, then do I have to buy another ceiling fan? (I sure hope not!)

Thank you 😊

OK, but what if I forgot to take a picture of where the wires were? How do I know where to put them back in?

I decided to fix the ceiling fan in my bedroom after waiting for weeks for my husband to fix it. This video is so simple to understand and follow that I know I can do with very little effort. Thank you!!

WHY NOT PUT THE COVER PLATES BACK ON?

Has anybody tried this on the Weber Smokey Mountian in the water pan without the water? it would seem to work just fine?

drive.google.com/file/d/15jeKtlizrRilohSBWufPgb_mS_0wezAT/view?usp=drivesdk

I'm trying to change a switch right now. I can't even get the little thing apart. And it always has 2 black wires coming out of that. So what does that mean?

I only have one wire and it's blue and I can't get the little thing apart.

I'm trying to change one right now. And I cannot get the little plastic piece apart

Who cooks five shrimp? In Louisiana we start with 5 pounds. Kick it up will ya.

How to make vegetables on the gril

How to do other things

I've tried to replace a few of them and the power would never work the same no matter what. I have seen many comments about doing this and they all say to buy a new fan. All of those switches are made only for certain fans. This is fake. I've seen nothing but negative and I even did 16 different patterns and it either runs to slow or to fast but you can never turn it off again. This is fake. It never works no matter how you wire it and I use a paper slip to push in and release each wire. No need to take the old one apart. I even got the switch from homedepot and their fans and it would not work. I have moderate speed but use the wall switch to turn it off and on. This doesn't work and I am very mechanically inclined, work on engines and do plumbing and electrical. you never showed it to us working.

I have switched the fan switch and compacitor and when i turn on i can feel thr motor hum but i can get it to spin. I am not aure if its wired corretly we bought the house and wanted to get it working. When i opened it the compcitor was exploded and switch was broke but still nothing any ideas???

B.S!!!! Replaced it and it still want work!!!

I have been doing it for years. The only downside you need to change the burners every 6 months because th excesive heat destroys them

Thank you for this video!

Hey Bill! Thanks for this video! Definitely an easy fix like yah said. 10-15 mins and done. BUT, I reused the soldered wires that were originally in broken switch! Made life much easier especially if you can recover those stab style wires! Had trouble with 1 red wire but eventually got it in! Job done! Thanks again!

My wire isn’t wanting to go inside the replacement switch. What’s going on with it?

I am trying to put wires in. They are bending - not going in. Can I stick a screwdriver in the slot to push them in like I did to get the wires out?

Thank you sir, you helped me out a ton! 😊

This was the best video I’ve seen for this. Thank you so much!!

one of the better videos I have seen today

Excellent instructions. Thank you!

Thank you. What a great view of how to do it. I never new about the numbersl When you call an electrician out . The bill is so padded. Now I know. I will do this. Thanks

Looks great, and with a brighter bulb installed that’s all the light you need. kzbin.infoUgkxWF88GpljEn-0o34vtLFazEQ5h5Q33SjU As far as ease of installation- this was my first ceiling fan and it took about 3 hours because I had no idea what I was doing and also it’s helpful to have a second set of hands and a magnetic drill bit. Works great.

I literally have 3 of them in but the last one just won’t go in, any tips?

Taste the meat not the heat.😂

I did what u said and it’s not working

If there are two pull chains, do they each have their own switch compartment? Or do both chains share the same one?

💪🏻💪🏻💪🏻💪🏻💪🏻💪🏻💪🏻

Little late but black/hot wire should be on gold screw…….and white neutral on silver

Awesome video

This is exactly what I want to do and almost identical idea, except I like that grill grate idea. I was thinking about those trays you can drop in, but your way is cheaper and more flame comes through. My goal is: 1. Stop dripping into bottom starting fires inside. 2. Increase the overall max heat. 3. Bring a little charcoal taste into the mix. Do you find that you get any of those results?

So my husband tore the fan apart and now can't remember which wire goes where. How can I put the new switch in if I don't have that information?

That is bull shit its not easy

Nice.

Ceiling wires aren’t tinned ends. Whose going to drip solder on the ends of the wires 6 ft in the air?

Don't take it apart. Dumbest ducking advice ever

Great idea.