Oh... I thought it cleaned up so well that you were just going to run it. What piston and rods are you going with?
@skythes1978 күн бұрын
@vicsstang89 I’m getting all the clearances checked and the cylinder walls checked ands honed for turbo Barra rods and pistons until I can afford forged
@vicsstang898 күн бұрын
@skythes197 I never looked into that idea. What's the price difference between the turbo rods and pistons. Compared to the cheap forged stuff?
@Jeepvanboat25 күн бұрын
Il give you some free advice.save up and buy the king 6 2jz these barras are junk.
@rickcambo7725 күн бұрын
Rods are junk , weak as
@Marie.S55027 күн бұрын
Those wheels look familiar 🤔
@yeetduck585427 күн бұрын
Miss this thing
@brandonickes8982Ай бұрын
Is the other video out yet?
@skythes19729 күн бұрын
Not yet. The engine is still at the machine shop getting worked on
@kenbull848Ай бұрын
Man I like what you are doing but don’t like your music so I out
@skythes197Ай бұрын
😂ok
@BrettViveroАй бұрын
Way to go bro barra the world with Aussie horse power
@chriseveringham5013Ай бұрын
Wow you got a lot of work to put in there mate,god that engine has had a hard life,so you can do some 218 B Kellford cams good bit of extra mid range but standard cams are still good,you gunna have to do pistons and rods cause there rooted,oil pump gears and backing plate, be sure to put a heavier spring in the oil pump to,it ups the oil pressure a bit more,quality timing chain,guides and use a ford tensioner there less prone to failure,put a race harmonic balancer on don’t use the standard one,do a new water pump,you will need crow or plazmaman valve springs,also after market head studs,use the bigger washer,the 12 mm head studs are good Timing chain crank sprocket,make sure you gap the rings right,there the main things and you won’t regret it ,these engines kick ass,I have one in my bf Typhoon
@skythes197Ай бұрын
Yup I plan on doing everything except for forged rods and pistons for now. I have turbo rods and pistons that are going in for now just so I can have it running and then I plan on doing coyote pistons and forged rods with an over bore because it’ll allow me to run a 9:1 instead of 10:1 compression so I can do more boost
@DeadshilzАй бұрын
@@skythes197good luck with that mate. You have a early 2002-2004 BA ford falcon NA barra engine there. Only good for maximum 420rwhp on them skinny tooth pick rods. You'll be bending rods in no winding it up pass 450. I'd be 100% doing them now while the motor is out, but car your, your budget. ✌️🤘🇦🇺
@fericydeАй бұрын
One of the higher US content cars is the Mustang. Just FYI for your friend. Is that a 6Boost exhaust manifold?
@skythes197Ай бұрын
It is indeed
@fericydeАй бұрын
@@skythes197 I'm looking at one for my FG -- not looking to make huge power, the mounting will be a T3 -- I haven't done a turbo before so trying to understand different mounts, intercooler BOV etc. How did you choose this particular manifold? Looking forward to seeing more of your build.
@simmyadvani6126Ай бұрын
your handsome;) also nice video
@nandiniarora4127Ай бұрын
hey bro, thanks for lending me your lamborghini the other day 😁
@dustinkeane5280Ай бұрын
🔥🔥🔥
@KS_Gaming052 ай бұрын
holding the wheel out the car is bold. loved the vid, first ive seen of you and wont be the last. look forward to continue watching you.
@GostesLoun2 ай бұрын
hello man great content i would love to keep watching your videos keep up the great work
@TemperDriven2 ай бұрын
Why?
@skythes1972 ай бұрын
Why what?
@lifedancecoach12 ай бұрын
Looks like you had an adventure 😢
@GostesLoun2 ай бұрын
it did
@anonneymous99493 ай бұрын
Awesome review. Just try this - those filter seems not giving you any better video. Just set it on auto. It is better then u think
@MaXpeedingRodsCoop4 ай бұрын
keep your work !
@briannareid94234 ай бұрын
Taxi motor is green rocker cover and a gas motor and it would have 400.000 km some have 1.000.000 and no manual taxis in oz
@jacka1472Ай бұрын
Plenty of petrol wagons were made by Ford Australia
@briannareid94234 ай бұрын
It’s Australian made not yanky
@vertex2354 ай бұрын
yooo this is sick
@KaseKnife954 ай бұрын
this has been a dream for me to do to my s197 mustang since i got it 3 years ago, i look forward to seeing how your build progresses! i totally wont be learning from it to do mine
@Colin-b2f4 ай бұрын
Dont worry boys . I didnt change the oil in my BF for 60 thousand ks still going strong . Cant wait to hear that Taxi Drone .
@caylebthomson74524 ай бұрын
Screamer pipe sounds wild on barras
@CAIDMASTEROFPYRO4 ай бұрын
It's Ford Australia not just ford. Barra was designed and built in Geelong
@wildman00sax4 ай бұрын
Don't forget the oil pump gears and valve springs! This thing is gonna rip when it's built up
@skythes197Ай бұрын
Yup those are on the way
@stevev6002Ай бұрын
And turbo rods?
@stevev6002Ай бұрын
Look up silver top vs red top Barra
@jamesd27145 ай бұрын
Duuuude this is literally something that i been thinking of doing if my 3v goes out lol can't wait too see how this comes out!
@claytonoldzkool26045 ай бұрын
Dang they sold you a taxi motor,.. I live in Perth WA, barraz are $400 here complete running engine.. And the turbo Barra is about 2k but you get everything, turbo, intercooler, ecu, ect… That motor you got is the worst I’ve seen, it’s not a good look for that mafia joint!.. lol I guessed a taxi motor before I heard you say it… Watch that oil pump man, upgrade that asap, they’re known to fail..
@skythes1975 ай бұрын
Everything is getting torn down to a bare block regardless so it is what it is
@claytonoldzkool26045 ай бұрын
Ahhh yep cool cool. You know it’s a killa engine, when they work, they work hard, it’s soo Much power, you’ll out do the streets fairly easy… I know you guys have biiig highways where you race so you’ll get some street use pulling at 1000hp.. 😂 it’s wild… it is a 4.0 2jz..
@Underservice5 ай бұрын
I’ve always had the idea of putting a barra on my s197 as well, thank you for sharing
@ReeshaRacing5 ай бұрын
Damn the pistons came out looking way better than I thought they would
@skythes1975 ай бұрын
For real same lol
@j-11595 ай бұрын
Bottom end Barra good for 700hp stock 😎
@skythes1975 ай бұрын
Not on the thinner na rods
@rickcambo7725 күн бұрын
Deaming with rods from a stock n/a
@ryanhern21265 ай бұрын
Can't wait for this build to be complete 🤙🏻
@j-11595 ай бұрын
Welcome to Straya Mate 😎🇦🇺🦘
@rvarsigfusson61636 ай бұрын
Just as mean as it gets...... Priceless machine.
@cl6ud3046 ай бұрын
real mechanics can taste oil viscosity.
@hithereperson81376 ай бұрын
What happened to v8s?
@skythes1976 ай бұрын
Overrated
@onlyinred16 ай бұрын
barra is one of the best engines ever, only thing to watch out for is when they're boosted, too much boost too quickly tends to turn the piston rods into spaghetti. unless you have the LPG engine, those internals are stronger. only other thing would be piston rings, again failing with too much boost. but if you can manage boost (dont have a turbo that spools up too quickly) and have a good tune, these things are bullet proof.
@briannareid94234 ай бұрын
No there not the I’ll pump gears fail when you hit the limiter and that’s a early Barra ba the fg motor is better or a factor turbo
@briannareid94234 ай бұрын
Oil pump not I’ll pump
@zoozinggaming6 ай бұрын
Badass dude
@Tarez2056 ай бұрын
Just earned a subscriber badge
@Logicilly6 ай бұрын
How much is the end price after everything needed just the way you built it?
@skythes1976 ай бұрын
Around 20k+
@Logicilly6 ай бұрын
@@skythes197 damn how much have you spent on you Mustang so far before the bara build? Love that you went through auto Mafia racing. I have a 2017 ford Mustang v6 and I used them for my tune
@skythes1976 ай бұрын
Don’t know and don’t wanna total it up 😂
@Logicilly6 ай бұрын
@@skythes197 well I just subbed bro #131 😂 can’t wait to see the build and when it’s finished 💪🏽
@rossb30826 ай бұрын
Only a few hundred subs? Bro I'm dropping a follow, this is tight
@skythes1976 ай бұрын
Thanks!
@yunosub12346 ай бұрын
why the fuck do you only have 100 subs dude this shits good editing is great energy is amazing wild dude keep it up
@skythes1976 ай бұрын
New to the KZbin thing haha. I appreciate the support!
@jeff5oh6 ай бұрын
oh shit man. you’ll be getting the views on this legendary
@ReeshaRacing6 ай бұрын
Yo this is sick
@dooby14456 ай бұрын
What will your rear diff setup be? Do you still have the 7.5”? Also how did you blow up 3 4.0L V6’s lol
@skythes1976 ай бұрын
I got an 8.8 off my buddy. Yes I still have the V6 parts. And lots of 2 stepping haha