Thank you!

Thank you for sharing ❤.I'm starting tomorrow vinyl plank floor in the basement of my great-grandfather built house. Love from Portugal 🇵🇹

You're going to kill your knees. Try the Kneeless Carpet Stretcher

That’s horrible. Look at the ends he so called trimmed off with his knife you see white. ROOKIE!!!!

That’s horrible. Look at the ends he so called trimmed off with his knife you see white.

This is so not the way to do this. Just use you’re LVP cutter much cleaner and more accurate cute by adjusting you’re LVP cutter to the 45 degree angle. Can you say rookie. I would have had mine installed already all the time he’s wasting. Once you start trimming off and shaving you lose a perfect clean cut

This is so not the way to do this. Just use you’re LVP cutter much cleaner and more accurate cute by adjusting you’re LVP cutter to the 45 degree angle. Can you say rookie. I would have had mine installed already all the time he’s wasting.

Sir ye kahan p milega or kitne ka hai

Caddilllaaaccc??

Thanks for the refresher course 😁🤙

You can make a TON OF MONEY in carpet Cuz as you said There are so few that want to get dirty or sweat anymore!! Only the Mexicans are doing it here in the Soith They will do anything to make a living Whites are very very picky on what they do.

Hi tell please what it would cost me for carpet installation for two bedrooms first room 1o foot by 15And 6 in Bedrooms number two 10 by 11 6 clauses in each room in the perimeter of the measurements I gave you. Thank you Please help i think home Depot is trying to.rip me off

This Hack has absolutely zero skill or material knowledge and should not be allowed on any job site.

Hack for sure!

How much Labor cost installing carpet tile

Is this guy kidding or what?

What if the boards under are soft pine? Worried about the blade 😬

Bro!!!! You are the MAN!!!!!! Now this is how explanation videos should be done! 🙌🏽💪🏽🤙🏽

You need to invest a bit more into some basic tools, bro. Like a straight edge and a seam tractor.

This is absolute diy carpet installation for sure. Invest $20 in a good carpet tractor and show how to make an actual blended seam. Same carpet and all…

As a professional flooring installer of 32 years, I’m insulted by this video. Lol.

We need to get a Brightly Lit Demonstration. and with a Very close-up picture while assembling the pieces especially the black slider. and.... slow down.... slow down

Just curious, how has this install held up? Do you regret using the knee-kicker vs a cross spanning carpet stretcher? Considering doing the exact same thing in my basement. Thank you for the video!

I freaking love it, dude I don’t know how I got on this trend of carpet installation. Oh wait, yeah I do lol Picked up a scrap of carpet was gonna make a rug for my drum set but all the videos I have seen so far you guys are awesome I love the fire jokes too. I’m more or less literally burnt my house down with a blow dryer. Yes, I was using it for heat. I bet you could figure out the melting point for that glue and get one of those handheld temp guns. That way you know 100% you’re getting it to the right heat and not overheating it.

Cant cut corners when cutting corners

I gotta say this is the first how to video that got it right. This the exact way to install cove base. Some butchers use hot glue guns to get the outside corners to stay. Thats because they don’t know what the hell they are doing. Some will even make a slit on the bottom toe of the base on the outside corner to help it stay again that’s a big no no. Well done video my man keep it up. And I’m sure you’d rather work with the 120ft rolls makes for a cleaner looking job and faster also. After some time we all know how those cove base seams shrink up and gap. Well done my man. 👍👍👍👍👍

Small tip: Don't score the plank on-top of the plank you just installed.

What is the best way to tack down outdoor carpet onto a wooden porch?

You should sell kits I'm in sir

Mike thanks so much for this video! You’re right, there are a lot of DYI people out there like myself who’ve never done this and wasn’t really sure which side was up so I appreciate your help! Thank you.

I’m finna use gorilla glue bcuz I got no time 😂

Next time do a closeup of cutting the triangle because some might cut it to small or big.

people really pay you ?

At home depot for everything with the exception of metal strips i pay about a total of 170 48 $ / box of tacks strips 21 $ for carpets blades 9 dollars for carpet pad staples and electrical staples top and 9 dollars as well for masking tape when i put pad down on concrete

Nice work. How would you crease and cut homogenous vinyl?

Why would you leave the baseboard on. This is very unprofessional

kicking that hard is going to require your knees to have surgery soon!☺

Brother could Please text the clue you are using

Good vid

Can put this in a garage ?

Much appreciated!

I appreciate you, sir

no way the sleazy p martini cameo. shits crazy

How to remove small burns

Do you have all your teeth 😂😂😂

You don't have glue up there, it's just kind of sticker

All your videos are extremely helpful dude. Hope youre alive and doing well. Peace.

Very cowboyish, people are paying for new strips and ur banging it with a hammer may aswell not bother 😂

Can I put it on carpet?

I have older berber carpeting. Can this be turned and tucked as well?