10k 🎉🎉🎉🎉 Get it palmed off that looks like a nightmare 😅

Crawford will have you working on his digger 😂

Any ploughing videos yet on the farm Ali?

Loved the podcast as well 👏

Great video Ali 👍👍

👍

Congrats on 10K Ali 😎 Keep up the great work 👍

Congratulations buddy !! Looking fresh mate much love from Dorset

Congratulations on getting 10k and thank you for your time and consideration top job 🛠️🔧💯🚜🚛🚜🚛🛠️🔧

Great job Ali on hitting 10.1 k 👏👏

Do you have to add oil to the air conditioner system to lubricate it ?

Yes Ali that dump truck deffintly needs to be in a workshop Far better to work on and dry . No chance you could have done anything to it .👍👍

Cheers Ali, that Aircon Pump Looks solid enough but you don’t know where these Parts are made half the time. That 40 tonner problem hasn’t just happened, if it’s been out then it’s been a quick refit and the mounting Bolts haven’t been tightened properly. If it had started vibrating a while back then that’s down to the operator. See you on the next one 🤙

Haha that dumper would be a good day on coal job ... usually run out on the tip n fix it there...or foot n mouth,next to the pyres with cows popping 😂

Very well done Ali. Keep it up mate.

Scrapnell / dirt of old broken airco compressor in system....??

So, is a visit to Crawford on the cards?

As you say, watching the old boys on those shovels 👌I bet it makes them feel like kids playing with the shovels all these years later

I bought a very rough bobcat e10 last week in an online auction. I have on order a variety of M6 bolts with hex flange heads to replace those miserable little button head screws.

👍

The fuse saver is a great idea but one can use a 12 volt incandescent light bulb across the fuse if there is a short the bulb will light up. (ohms law) about the only thing I remember form school days :)

I would almost put money on it the 225 with the cracked plastics is cleaned with a pink cleaning product? The dam stuff used in excess also known to cause bad contact electrical problems if it gets in fuse board or elec connections

Hi Ali keep up the videos spot on. I worked for a well known country wide Hose replacement company and you have hit on one of our main problems different fitting types on the same piece of equipment!! The worse was probably ORFS I would travel up to 100 miles sometimes to replace an "O" ring which could only take 5 minutes.

10.000 subs congrats <3

Cheers Ali, a good variety there, but not untypical for a mobile Plant Mechanic. See you on the next one.🤙

14:40 I've had those errors before, taking out the sensor and wiping them off usually fixes al the issues for me.

Awesome video thanks Ali for your time and consideration top job 🚜💯🛠️🔧🚜🚜🚜🚜

Great video! It’s been a busy time for u. U will have to give Joe seels some advice on his old digger

Hi Ali...I have both agricultural tractors and an 8 ton machine.Why,oh why dont excavators have cab (at least) and even body suspension ? They would jar your teeth out on hard ground.

ali pls dont say everything goes wrong 4 a reason my m8 aged 51 died yesterday never smoked never drank no drugs ,, so im dammed if i can find anything good out of that

Hi ali I think you was travelling behind me on wednesday just before denholm I was in a white sprinter with one yellow rear door

What are the advantages of "high -track" set-up on diggers ? Also, where do you think the 5 ltrs. of hydraulic fluid went ? It is a "sealed system" is it not ,so you should see some sort of seepage somewhere?

Ali, a lot of manufacturers state you can use engine oil in the hydraulic system, 15/40 listed where I have worked, makes the oil darker but not harmful to the components 15/40 is between 46 & 68 grade, we also used to use FNH(Ford New Holland) 10/30 oil in hydraulics.

Yeah 10K, all that is needed is all those that watch, hit Like👌👍💪💥

Congratulations on 10k. Still nothing better than a grumpy Ali, makes my day so much better. 🏴󠁧󠁢󠁷󠁬󠁳󠁿

Congratulations in reaching 10 k subscribers well done 👏

Congratulations on the 10000 subs, well deserved.

I use copper slip on bolts that take a lot of heat

See you hit the 10 k mark

Just watching your video and subscribed as Crawford of Crawfords Farm sent me over. 😊😅😊

Congratulations on the 10k

Thanks ali for the great video, nice to see the old machines, would like to have a go at operating one? And for the service truck, plenty of room inside. Not a lot of ground clearance 😊take care mate. Looking forward to more videos Gary 😊

👍

Cheers Ali, I do drop into Threlkeld occasionally, not far from me. I used to work on Crawler Cranes years ago so can relate to what’s going on here. The last time I did breakdowns and repair on these was around the millennium so they were still being used then and occasionally now although not as a face shovel. Hope you had a good time. All the best for now.

congrats on 10k

Do it very similar to you but always find having the machine just off the ground makes it easier having it to high makes it harder

Great video mate, was a good day out with yourself and Dave

Where this place Ali?

Ali, do you know what engine is in the excavator you got to look around? I couldn't see what was on the rocker cover. Was wondering if it was one of the big engine manufacturers like Lister maybe?

Great video again bet none of them machines had bother with ad blue 😂😂😂