Mellowpine Woodworking

Пікірлер

@gregmize01 20 сағат бұрын

dust free...oh, man I wish!

@roldantiansesab 2 күн бұрын

Easy Tip..thanks

@tiredgardener 4 күн бұрын

Excellent video, wish I had watched it earlier. Made a bit of a mess trying to do this with a jigsaw.

@STiMonkey 6 күн бұрын

I didn't know the trick about the masking tape. Thanks!

@Mike-rx3mn 6 күн бұрын

Very helpful, Thank you.

@peterbarlow8912 9 күн бұрын

Technically a long subfence or a block to skew a workpiece is a jig. google definition #2 anything that holds a workpiece or guides a tool. The long straight subfence is essential so workpiece shim block assembly is registered against a fence throughout the cutting process

@aridianuh331 11 күн бұрын

Never worked

@CaptainWrinkleBrain 12 күн бұрын

What ratio should I start with when thinning poly

@gregmaggielipscomb9246 17 күн бұрын

Excellent, T/Y !

@21a551 17 күн бұрын

Can we apply oil right after planing ? Is sanding necessary after planing?

@arshk3612 18 күн бұрын

Many thanks - table saws scare me and this is such a straightforward way of cutting these to start basic woodworking with tools I have .

@dorianf1456 20 күн бұрын

Thank you so much. Amazing idea.

@bierbarrel 21 күн бұрын

lol

@decespugliatorenucleare3780 21 күн бұрын

you absolute legend!!

@glenbutler9611 21 күн бұрын

Thank you for a clear, concise, show-as-you-go blog!

@williamkennard4663 22 күн бұрын

Useless video

@sheelaandrews7321 27 күн бұрын

Morons , circular saw blade tips are made of carbide and it is impossible to be sharpen with sandpapers.

@hubhubble Ай бұрын

You didn't show how to set up properly.

@symcardnel1741 Ай бұрын

Step 1. 0:28 place your square against an unsquared edge???? Step 2. extend that unsquared line with the help of a level or ruler Step 3. your screwed Step 4. throw piece of said wood in burn pile

@Miner39er Ай бұрын

This was my assumption but nice to see confirmation. Poly finish on my walking sticks seems softer than other finishes and wasn't sure if it would sort of tear off with sandpaper.

@HTrntrs Ай бұрын

Mehrbani

@alexpaterson1382 Ай бұрын

I hate table saws.

@ht6691 Ай бұрын

Excellent video

@user-wr4uz8pg7m Ай бұрын

Thanks. You were the only video I watched that mentioned using the arbor lock button!

@GoatMalp Ай бұрын

You had me at "quick guide" 🥹

@Nicholas-if7bl Ай бұрын

as cue and cure generally we have hard y; either \'æc-jə-rət\ or accu\writ\

@jose2226 Ай бұрын

How do i make the straight edge? Thanks gor upload btw

@bloodyconfessor Ай бұрын

damn those are some black hands

@MichaelPaszkowski Ай бұрын

Very neat, but unlike the title, a lot of jigs.

@nancysays3262 2 ай бұрын

Thank you. I appreciate you explaining clearly without any unnecessary talk. 😊

@olgringo-421 2 ай бұрын

After 7 months this is still the best method for ripping tapers that I have found. So easy, so quick, no jig needed - just outstanding!

@evaburgess3648 2 ай бұрын

Used your foam method this past weekend. Excellent for cutting thin plywood & impressed my husband. Winning

@KJ7JHN 2 ай бұрын

Hello. Informative video, thanks. If you measure from bearing centers of the wheel, and add circumfrence, how close does this come to your actual measurement? Z = bearing center to center. So: (2 × pi × r) + (2 × Z).

@rpuxa Ай бұрын

I've measured my blade to be 80" long according to the video, by laying it down and walking it by the ruler. Next, I've tried your method (2 × pi × 6.25") + (2 × 20.25") = 79.77". I believe my sloppy measurement has resulted in that small error to the true dimension.