Half hour my foot. If you live in the rust belt that EGR tube is gunna be seized like you've never seen before. Use heat but it's close to the firewall which is full of a cotton-like material so be careful
@deizel295Ай бұрын
dude, lock focus, I couldn't finish the video due to the horrible focusing and refocusing. My migraine came back.
@ChrisThacker-y4dАй бұрын
The 4cyl pvc valve has crush washer and has a torque spec of 33 ft pounds
@peterluig41882 ай бұрын
I have the exact splitter. I also got it from a friend about 20 years ago. I mounted it in my wood storrage rack because the wheel shaft was hit and bent.. The cylender started leaking and I was wondering if you knew what rebuild kit to buy. You did give me a clue because I did not know it was a Duerr. Ill start a serch from there but if you have any info on a rebuild kit I would realy appreciat it. Thanks!
@berkscatbill55822 ай бұрын
thanks for posting
@carolynnoriega70452 ай бұрын
Thank You for your thorough, calm and patient explanation.. You rock and yes, I can tell that you definitely are an engineer. I know how to tackle this egr issue now 🌺 Best to you.😊
@rstuartwilson71273 ай бұрын
I agree, this video doesn't show any seat "replacement" info. It only shows how to replace the switch.
@JesseEdwards-is1km3 ай бұрын
Good at going step by step and easy to understand good job guy !
@JesseEdwards-is1km3 ай бұрын
I like this Guy!
@PainterD543 ай бұрын
When bolting the frame together, you should measure from corner to corner to get it square before tightening the bolts.
@operaguy13 ай бұрын
11 years later, $545
@OEFarredondo4 ай бұрын
Its 2024 and your video saved my Bass. Thank you
@cherylelinsmith7434 ай бұрын
Update on EZ-DUZ-IT, I was using it wrong with canned Tuna. I was trying to use it on tuna can while on counter. It wasn’t clicking on can and opening. Got so frustrated I thought I got a dud or knock off. Turns out you have to hold can in your hand in air. It will click and open. Feel so stupid, live and learn.
@gaylonwyatt22414 ай бұрын
Will a control arm from a 2000 explorer fit a 1998f ,150
@Vicos4 ай бұрын
You would have to look up the P/N for each and see if they're the same. You can probably do that on Amazon.
@alouisschafer72124 ай бұрын
Awesome how quiet this sander is!
@aj5555414 ай бұрын
Thank you
@Comm0ut5 ай бұрын
That style mount with either square or round shank clamps nicely in a tristand chain vise or pipe vise permitting your bench vise to rotate which is quite handy for welding because you can rotate your workpiece at any angle.
@madman4320005 ай бұрын
somebody needs to make a walk behind tiller with side drive for the tines, eliminate that ridge in the center.
@kyfisher36625 ай бұрын
this is perfect for me, wish i could find one forsale in Australia, looks like im gona have to make my own
@WalterO19595 ай бұрын
So why didn't you video the removal of the glow plugs
@AmusementArchive6 ай бұрын
Great footage! Thanks for sharing!
@IanHodgson-fj8kh7 ай бұрын
Thanks...
@paulkeplinger35657 ай бұрын
Thank you EGR=Exhaust Gas Recirculation
@Vicos5 ай бұрын
Yep, just wasn't worth the time to go back and correct the video.
@robertelliott32117 ай бұрын
make sure the two hose are good on the flow sensor, thats all that was wrong with mine simple stuff first
@basketballmaven14548 ай бұрын
swing-a-way brand is the best
@nickc74948 ай бұрын
Excellent content, a couple quick tips, remove both 10 mm bolts holding the egr in, move the egr over and clean both ports with carb cleaner. Also spray both banks (egr tubes connected to exhaust manifold ) also. Make sure all vacuum tuning is in working order, I suggest also removing intake snorkel and cleaning throttle body. Lastly a good fuel cleaner added to a full tank of fuel and steady highway speeds to push out all deposits
@jimfeaster48378 ай бұрын
Does it pop breakers?
@Vicos8 ай бұрын
Never has. It is on a 20A circuit where serves everything in the shop except the lights.
@JONBOYLEMON9 ай бұрын
where did you buy those glow plugs from I cannot find them anywhere
@Vicos9 ай бұрын
That was a while back, but I think I found them on Amazon for the best price.
@mentalllllll9 ай бұрын
I just removed my EGR valve on my 1999 Ford Econoline E-150. I had to size up the nut. I ended up buying a 1 1/6 crescent that fit perfectly. Then I used a 10 mm crescent on the smaller nuts and it pulled loose. However, I do want to note that I also bought some PB Blaster and sprayed it good before I started removing the nut. I let it sit 5 minutes to make sure that it generated through the rust BEFORE I turned it for the first time. Just a little effort. Watch that thumb knuckle! And don't forget to spray down your nuts and screws with PB Blaster and let them sit for a bit before replacing them back into thee hole. You might want to spray down the holes themselves too with PB Blaster.
@CZ3ro9 ай бұрын
Wonderful!!! I've been a mechanic for 109 years and I only learned how to fix cars now, because until now I just watched how it was done. For the first time in my life, I grabbed a tool and realized how difficult it is to unscrew a nut. I've been working for two days and it's great! !!!!!!thank you
@cherylelinsmith7439 ай бұрын
I was lucky to get the EZ-DUZ-IT from Rainbow Restaurant Supply on the Bowery in NYC. I tried it to open canned salmon, really nice. Someone said though that when he washed it, it rusted. What about water, should I just wipe it down with a paper towel instead of washing on the sink. I'm not a fan of buying on Amazon, sometimes they can be knockoffs. It cost me with tax $16.28 Cuisinart one I had barely lasted 2 years.
@geronimocruz91239 ай бұрын
Thanks for the upload
@cujet10 ай бұрын
PL14476 is what I use.
@jimmathieson954910 ай бұрын
Great introduction to Augers,thanks
@GeorgeGraves10 ай бұрын
CUTE CAT!
@kennethboyer233810 ай бұрын
That lumber is way over the top. If that is oak you could've had them cut down to 1" thick and it would be more than enough. That probably takes away at least 100 lbs off of your capacity.
@garrymarin733610 ай бұрын
A lot of times, you may have an oil leak going into your alternator, it may be the o-ring on in the Pcv valve. Easy fix, drove me crazy thing it was the valve cover gasket
@2lotsill11 ай бұрын
Thanks. Sound like Eric the car guy.😀
@Vicos11 ай бұрын
I've heard that a few times. Thanks for watching. Hope it helped.
@Iamtherodlight1453.11 ай бұрын
Awesome
@georgetrevino572411 ай бұрын
Thank you Brother for your excellent video
@Vicos11 ай бұрын
Hi George, Many thanks for the kind words!
@willysnowman Жыл бұрын
How is that sticker holding up? Alex is broke for lying and profiting off dead children. Bonezpurz is a convicted rapist who is about to be locked up.
@grant7517 Жыл бұрын
$98 today. Damn inflation. Looks solid so far
@alouisschafer72124 ай бұрын
73$ USD here which is 68€ for us.
@jafinch78 Жыл бұрын
I almost want to weld the whole frame together and save on the bolts use, plus free up some space and lighten up slightly.
@lisareeves5095 Жыл бұрын
Yes this help me alot.and because of these wrong people is why I started working on my own truck.i like my truck and it seems to be fairly easy to work on except for # 8 spark plug it's so hard to get to and it seems to be stuck .seized so it seems to be called.byt you help I failed to connect one of the plugs. Thank you for your video it truly helped
@irunlikemonkeys Жыл бұрын
Maybe the torque spec was 35 inch pounds. That would make more sense than foot pounds.
@realflyersrc4416 Жыл бұрын
Talking about lupe and pron camera making noise. Awesome video
@ss442es Жыл бұрын
Thanks, my 2003 F-150 decided to throw a P0401 so been looking at videos to fix the problem. Inspection due this month so the misfit problems always seem to find the inspection month. Will do this myself.
@rodneystalder2752 Жыл бұрын
Thank you for the video and explaining everything .I’ve been dealing with issues in my 03 mustang gt and my throttle body was clogged as well .perfect video thank you again
@Reviews-Tidbits Жыл бұрын
So you have a trailer that you can put about 1k load?