Mike Zimmerman

Пікірлер

@Sawyerelectric213 25 күн бұрын

That pool panel only allows copper conductors. Yes it will work with Al but it’s done wrong.

@cahillkieran Ай бұрын

It works perfectly , found 3 hidden solenoids in approx 10 mins of using . Very happy

@leejohnson5158 Ай бұрын

Just wanted to thank you for this

@MattLennander 2 ай бұрын

Any chance you could do a startup procedure in the spring? Or is it just putting everything back in place and starting up in the water?

@joshsutcliffe6099 2 ай бұрын

Did the vtage reducer come with the kit

@robertkulikowski803 3 ай бұрын

Great video!, I have one additional suggestion, I pull the transmission cooler out of the hoses and I always find a bit of seaweed at the end nearest the impeller

@NoFlightZone 3 ай бұрын

Thanks a lot for this ❤️

@NoFlightZone 3 ай бұрын

How freezing is it at your location during the winter? If done following your list, minus degrees will not hurt the engine at all then? Seems like a much quicker way of winterization than conservations of the complete engine with anti-freeze fluids etc 👍🏻 You never had issues in the spring doing like this as I can read in the comments? 🤠 🫱🏻‍🫲🏻 🤠 👍🏻 Storing the fuel tank full or drained as well? Best regards, SUPRA in Sweden 🇸🇪

@montemag 3 ай бұрын

thank you for a great video. I am just like you. We both do the same things. I also have my half above ground pool-2 feet in ground and 2 feet above. I also did not know what I was doing for many years. I was adding powder shock etc etc. But then AI found a site called Trouble Free Pool (TFP) and they really talked me through a lot of the correct ways to maintain a pool. Now all I add on a daily basis as well is Chlorine from Walmart also abut $5.20 per gallon. I also check pH about once per week and CYA like about every 3 weeks or so. Along with TA. I have been following TFP now for 2 years and I only had to add Muriatic acid twice over that period. And a little chlorine stabilizer when the CYA dropped a bit too low. When I first met TFP my CYA was well over 100 also but I was adding so much GREEN OUT shock powder that even though my pool looked clean- the chemicals were out of whack. I drained half the pool and refilled separately and now I am pristine clean and balanced. My question for you-is- when do you close your pool? I live in Long Island NY and from the first week of September it gets real cool in the morning. My pool gets pretty cool from here on in. So, I close the pool MID September, and I slam the pool with lots of bleach to keep it good until May 31 st of the next year. This year was my first opening since meeting TFP and when I opened the pool- it looked great and was pretty well balanced. Do you have a heater for your pool? I ama thinking of getting one. We had a gas heater a long time ago but the water being unbalanced destroyed the elements inside the heater. I am wondering about the difference between a Heater PUMP type of unit or getting a gas heater again. TFP says to get a gas heater since we already have the gas line installed. Any ideas? I also muse the pool math ap- really simple and you can log your results for the TFP to see and help with.

@BlakeDumas 4 ай бұрын

$60 a month for chlorine will guarantee a clear and clean pool. *follow me on how to spend your money faster 😂

@bentley625 4 ай бұрын

I also use tfp this is an excellent overview. Hey do you have a closing video if not would love to see you make one.

@MikeZimmermanOfficial 3 ай бұрын

I actually hire closing out. I don't mess with that. :)

@prebaned 5 ай бұрын

Put the drips in the drops...

@MikeZimmermanOfficial 3 ай бұрын

hmpf

@HEAVENLYTUNESDJANGEL 5 ай бұрын

$60 a month 😮

@MikeZimmermanOfficial 3 ай бұрын

That's a lot? Cheaper than tabs...

@andymoe44nez53 5 ай бұрын

Well its not very trouble free if you have to check adjust your pool chemicals every day. But you have convinced me to get rid of the test strips and get the Taylor test kit.

@djrikk214 4 ай бұрын

It’s a pool. It needs regular maintenance. Trouble-free just means you won’t run in to “trouble”. And yes. The test strips are complete garbage. Get the Taylor K-2006 for chlorine pools

@MikeZimmermanOfficial 3 ай бұрын

I've done my job here if you ditched the test strips.

@ichbin27455 5 ай бұрын

I'm in the middle of finding and repairing a couple of buried valves. The system was already installed before we purchased the house and there was no location map. Anyone who would install a system with control valves spread around the yard, rather than putting them in a single box near the house, needs a "talking to." Makes no sense at all!

@jagboy69 3 ай бұрын

I agree it's stupid, but it saves on cheap pipe and lowers the risk of more joints that are likely to leak. I would rather them all in one location.

@MikeZimmermanOfficial 3 ай бұрын

Amen. This was a self installation also. A guy and his "buddies" installed this and you could absolutely tell. I moved away from this mess thankfully.

@FredDurst-z8f 5 ай бұрын

TFP is a cult. “I follow the tfp method and never get algae!” Neither does anyone else that uses 5 times the amount of chlorine than necessary. The TFP method is to get you to stand on the edge of your pool and throw money into it. I would bet anything that TFP could be traced to DuPont chemicals or advocacy group for the swimming pool industry. These people are lying snakes with an ulterior motive. They falsely claim that you cannot use sodium bromide algaecide in a chlorine pool because it will forever convert it to a bromine pool. This is bullshit. I just did it and within a day and a half, all the bromides had degraded to bromate and all chlorine consumption by the bromine stopped. And it worked much, much better than their method of maintaining 30 ppm chlorine for day after day. One night with 2 pounds burnout73 and 10 oz of yellowtrine worked ten times better than three days of 30 ppm chlorine to get rid of yellow algae. So figuring they’d be happy to hear that sodium bromide works great and causes no problems at the levels used for algaecide, I posted what I learned on their forum. The moderator immediately contacted me and gave me a warning about “attacking tfp methods” and gave me 4 demerits like I’m in kindergarten again. Then every other lowlife tfp salesman on the site tried to discredit me. It’s like I was a revolutionary and I just wanted to tell other pools owners that bromide works great and causes no problems when used as directed.. Then they banned me for questioning why they were so determined to prevent people from knowing sodium bromide algaecide works. I don’t know why, but these people are determined to get people to increase their chlorine consumption by 4-500%. Instead of 1.5-3 ppm chlorine, they want you to aim for a minimum of 8ppm. Instead of doing normal shock levels supplemented with 4 oz sodium bromide for every 10k gallons of water they want you to spend over 100 bucks on a fas dpd test kit, get the chlorine ppm up to 30 ppm and maintain it for days to a week and then permanently jack up your chlorine use by 500% above recommended levels. The way they attacked me for just sharing a tip shows these people have an ulterior motive.

@Tessaslife31 6 ай бұрын

Don't throw it! Just place it in mine floated

@MikeZimmermanOfficial 6 ай бұрын

Ha, that doesn't really simulate real life events... like dropping it off a boat.

@Tessaslife31 6 ай бұрын

@@MikeZimmermanOfficialHa! That's true I didn't think about that! I just thought about like you swimming and having floating right there for you! 😂

@HEAVENLYTUNESDJANGEL 6 ай бұрын

AQUACAL doesn’t sell the og part the heater? Mines take for ever to get to the set temperature. Example it shows 82 or 84 and i set it for 89 or 90. Hot water is coming out but not moving the temperature on display. My salt generator will show the actual temp 89 or 90.

@MikeZimmermanOfficial 6 ай бұрын

Sounds like a bad sensor to me.

@HEAVENLYTUNESDJANGEL 6 ай бұрын

@@MikeZimmermanOfficial I'll order one and replace it. Thanks

@jamesvirga9496 6 ай бұрын

Just got this kit and I totally disagree about this kit. They sent the wrong resurgent for the tests, instead of 007 008, 009, I got 007, 008, 007 also instead of 0010, 0011 and 0012, I got 0010, 0011 and 0010. What garbage, no refunds of course because everyone would want a refund. total wast of time and money

@MikeZimmermanOfficial 6 ай бұрын

I'm sorry for your monetary loss.

@Shortwheels316 5 ай бұрын

That's quite a bit of Free Chlorine at 8.5. Thanks for showing..

@Richard01234 6 ай бұрын

Are there people who use the TFB method but use the chlorine pucks and supplement?

@brandonkick 6 ай бұрын

The only reason you do not want to use the pucks is that they are almost always stablized. In other words, they have stablizer in them. Now, don't get me wrong. You DO need stablizer in your pool. But if you get too much, it's just as bad (or worse even) as not having enough stablizer. The stablizer (CYA) plays the role of protecting your chlorine from sunlight. Without stablizer, the half life of chlorine in sun exposure is very very short. Hours at best. BUT as stablizer increases, it also diminishes the ability of the chlorine to do it's job. So you need higher chlorine levels. At a certain point, if stalbizer levels get high enough, they make it so the chlorine just CANT do it's job. So you need a nice balance, a good range of CYA. Usually for most non salt pools you want around 30 ppm to 40 ppm of CYA. And then your daily "swimming level" chlorine targets are going to be around 5 ppm to 7 ppm. All that is to say, if you use the pucks on a prolonged basis... each day your CYA level will build little by little. At a point, once it starts getting to 70 ppm, 80 ppm... 100ppm.... you will have to drain your pool some and put fresh water in to dilute out the CYA. For that reason, I use calcium hypochlorite.

@MikeZimmermanOfficial 6 ай бұрын

I still use pucks here and there, mainly when I'm gone on vacation, but as @brandonkick explained they slowly increase your CYA level so that's why I avoid them. There are pucks out there that don't have stabilizer in them, but they're much more costly than just using liquid chlorine.

@jimbeam-ru1my 5 ай бұрын

@@brandonkick "chlorine targets are going to be around 5 ppm to 7 ppm. " 5 to 7 ppm is a low chlorine range for TFP. If you have 60 ppm CYA then they want you to use 5-9ppm. According to TFP, the CDC is full of shit when they say chlorine levels above 6 ppm are unsafe. But then TFP is a "product awareness" outreach by the chlorine manufacturing industry with the goal of drastically increasing chlorine usage by ignorant homeowners trying to maintain their pools but too lazy to learn how. Like this guys claims about the pucks constantly raising CYA. CYA needs to be constantly replenished because it degrades just like everything else. The pucks don't raise the CYA level, they maintain it. However, since TFP is a con for ignorant homeowners that use trichlor or dichlor to shock their pools, which has cya in it, they convince them that it's the pucks raising the CYA, not using the wrong kind of chlorine. "The only reason you do not want to use the pucks is that they are almost always stablized. " No, that's the reason you do want to use pucks. Maintaining cya is part of their job.

@KipCount 6 ай бұрын

Nice overview. I've also adopted the TFP method after using pucks for years and sort of blindly stumbling my way through with test strips, running into issues and never full understanding why. My first impression of TFP was that it was complicated, but after understanding it better, it quickly becomes obvious that this IS the easy way.

@MikeZimmermanOfficial 6 ай бұрын

It does feel overwhelming at first, but once you get the hang of the water chemistry you learn how your pool reacts to things and can pretty much predict what you need to do.

@FredDurst-z8f 5 ай бұрын

You fell into a money sucking cult and now you’re going to triple your cost to maintain a pool. Of course their method will prevent algae, but so would any method that calls for jacking chlorine to 500% of recommended levels.. This is what happens when people don’t want to learn and just want someone else to think for them

@jacquelineverdile9005 6 ай бұрын

Also can you actually show how you do every test on the 2006c im easily overwhelmed and get really anxious and upset when I don’t understand instructions right away.❤

@jacquelineverdile9005 6 ай бұрын

I learned!! I am now testing every day lol! My results are so different from Leslie I’m nervous… on Reddit they argue that pool store computers are accurate and these test kits could be old, sitting in a hot warehouse etc… I mean I just don’t know!

@MikeZimmermanOfficial 6 ай бұрын

Leslie's wants to sell you things. Trust your home test kit that has nothing to gain from the numbers it tells you.

@jacquelineverdile9005 6 ай бұрын

Omg thanks for showing this- I just got that 2006c test and this powder stuff had me so confused especially the *note- between step one and step 2. I still don’t understand the math. If I use the 10ml mark and add 2 scoops, then add the 0871 and count how many drops, I always divide by 2? Why would anyone use the 25 ml 0.2 ppm equation? What would that math look I need help with TA AND CH-don’t understand the directions

@polsksm1 6 ай бұрын

If you use 10ml sample, use one heaping scoop or two smaller scoops. Swirl to mix. Add drops of 0871 counting and swirling as you go until the water turns clear. Divide number of drops by 2 to get FC. So for example if it takes 10 drops to turn the water clear, your FC is 5ppm. I use 25ml personally because it is more accurate/precise. Probably not necessary and you'll go through more reagent, but I feel more comfortable with the results. In that case, 25ml + 2 scoops of powder. Then 0871 until clear. This time you divide the number of drops by 5. You can do it in your head if you divide by 10 and double it. So for example if it takes 17 drops to turn the water clear, that means you have FC of 3.4ppm (17/10=1.7 ... 1.7*2=3.4). As far as the swirling goes, do yourself a favor and buy the taylor magnetic stirrer. It makes theses tests 1000% easier since it does all the swirling for you (and does a better job of it too). Oh and visit troublefreepool.com! Tons of information and very friendly/knowledgeable people who can help you with any questions you might have.

@MikeZimmermanOfficial 6 ай бұрын

Not sure why anyone would use the 25ml mark, but you're correct. When using the 10mL mark, divide the number of drops you put in to turn from pink to clear, and that's your FC ppm.

@DoctorBlankenstein 6 ай бұрын

Did the repair work? My sensor is reading too high as well, but it is also not turning off when it goes beyond its set temp. Think it's the sensor... ? Or maybe control board?

@MikeZimmermanOfficial 6 ай бұрын

The repair worked for me. Heater kicks on and off based on set temp.

@DoctorBlankenstein 6 ай бұрын

Worked here as well! Video was a big help. 🙏

@MikeZimmermanOfficial 6 ай бұрын

Great to hear. I'm glad it was helpful!

@kenbrown8186 7 ай бұрын

Thanks for taking the time to post this.

@MikeZimmermanOfficial 6 ай бұрын

Glad it was helpful!

@Chummybuckt 7 ай бұрын

Thanks! I just ordered a Taylor k2006 just came across TFP going to give this a shot the pool store has robbed me of over 500 bucks and the pools been open for a week… (central Michigan) still very cloudy blue. I’m frustrated and wanting out of a pool is an understatement, your videos are much appreciated!

@MikeZimmermanOfficial 7 ай бұрын

Stay with it. While you wait for your kit go get a few gallons of liquid chlorine to start clearing up the pool.

@Chummybuckt 7 ай бұрын

Okay kit came in my readings are ph- 7.8 Cya- 40 Fc- 26 pmm Ta- 140 pmm Ca- 250pmm Trying to get familiar with pool math calculator I paid for the sub. Any guidance?

@teresahoss 7 ай бұрын

That’s exactly how to take care of a pool, it’s not hard at all and Trouble Free Pool is where I learned in 2015. Go to pool store only for floats.

@FredDurst-z8f 5 ай бұрын

So where do you get chlorine from?

@BetoisDmentD 7 ай бұрын

This really works too

@MikeZimmermanOfficial 7 ай бұрын

Thanks for watching

@Mowasfla 7 ай бұрын

Youre doing it wrong

@MikeZimmermanOfficial 7 ай бұрын

What's new?

@todda8695 7 ай бұрын

Just ordered my sensor too. Thanks for the video. I know my pool isn’t 104 degrees as it says now . :-)

@MikeZimmermanOfficial 7 ай бұрын

This should fix it... mine was doing the same thing.

@lisakunish936 7 ай бұрын

This is a super video! Thanks so much for putting this together, Mike. I need to do this weekend... Hoping I can find a direct replacement for my thermostat, but if not, it looks like a reasonably priced one could be obtained from Amazon.

@MikeZimmermanOfficial 7 ай бұрын

Good luck!

@detkie 8 ай бұрын

Thank you! I was able to fix my heater by following these steps…this is the best video on this topic for AquaCal heaters.

@MikeZimmermanOfficial 8 ай бұрын

Appreciate you watching, glad it helped! Pretty straight forward and simple for a diy job.

@javtheautoenthusiast6418 8 ай бұрын

I recently decided to take over the maintenance of our pool. We had a pool service for over 3 years but since installing cameras around the house got to see that our pool guy really didn’t do much other than place chlorine tabs in the skimmer which, I learned is also bad in itself. Well…what I discovered after learning to test my water is that our pool was not balanced at all and our CYA was well over 200. I’m in CA so we always have our pool open. I had to completely drain and refill to start from scratch. I came across trouble free pools forum and now my pool chemistry is balanced. Using just liquid chlorine and muriatic acid after the initial refilling of the pool. Like you said, the trouble free pool method is very easy and my pool looks great! Thanks for sharing.

@MikeZimmermanOfficial 8 ай бұрын

Thanks for watching, couldn't agree more!

@jimbeam-ru1my 5 ай бұрын

Fired his pool service and had to completely drain his pool soon after only to refill his pool and use so much chlorine that he could have just left the 200ppm cya water in. Now he's spending more on chlorine than it cost him to pay a pool service, and he has to maintain the pool himself. And the excess chlorine shortens the lifespan of his pool TFP is the product outreach arm of the chlorine manufacturing industry and their whole goal is to shift public perception to drastically raise chlorine consumption. The people that use the TFP method are homeowners that wanted to maintain their own pool but didn't have the time or patience to learn to do it correctly so TFP swooped in and got them to use five times the chorine they should use because no matter how bad you are at maintaining a pool, nothing's growing in a pool with that much chlorine in it, so the homeowners think it's working but don't understand the side effects of too much chlorine.

@javtheautoenthusiast6418 5 ай бұрын

@@jimbeam-ru1my you couldn’t be more wrong. I was paying $150 per month on a pool service. I only spend $35 month on chlorine (1 gallon a week) and maybe $30 every two months on muriatic acid. Plus, with our pool service we started to see algae growth on pool tile and my guess is that of our CYA level and an unbalanced pool. Say what you will but my pool has never looked better. You must be a pool service operator.

@jimbeam-ru1my 5 ай бұрын

@@javtheautoenthusiast6418 1 gallon a week eh? What ppm do you maintain? And what do you spend on cya? What did you spend to drain the pool and replace all the chemicals? How often do you"slam" your pool, and if so how much chlorine do you go through then? How much money do you spend to use the chems in the fas dpd kit rather than test strips and a 5 way? How much did you pay for the fas dpd? "Say what you will but my pool has never looked better." Of course it does. When you have enough chlorine in it to kill an elephant then you don't need to worry about algae.

@javtheautoenthusiast6418 5 ай бұрын

@@jimbeam-ru1my here are my current pool readings CYA: 45 Ph: 7.6 Alkalinity: 80 Maintain chlorine at 6ppm I drained the pool to the floor level myself in April which got me down to a CYA of 50. That should tell you how high the CYA was prior to draining the pool. Got an exemption fee waiver from the city to refill the pool. Only had to buy calcium hardness in addition to the regular maintenance chemicals of chlorine and muriatic acid. So not much spent on reopening. I have not ever had to slam the pool. I purchased a Taylor test kit in April and have enough testing agents to last a year. Testing strips are garbage. Any other questions?

@edikaramuratful 8 ай бұрын

How i hate when they do movies before riding it 😏

@MikeZimmermanOfficial 8 ай бұрын

yes...

@azvidz5711 8 ай бұрын

Hello, I was wondering if you could help me or give me some pointers to try and fix this light issue I have. I got the OmniPL retrofit kit and installed it on my ProLogic panel and everything works great except the lights… when I turn them on they turn on for about 10 seconds then they turn off and stay off. I tried different shows, fixed lights, modes (UCL, CL 4.0 etc) and it does the same thing. What could be causing this? I followed the instructions to a T. Also, when the lights turn on they always turn on to a dark violet/pink color and nothing else, I hit red, blue, green, white and none work… only the violet/pink color. Also, my lights are ColorLogic 4.0. 2 pool lights and 2 spa lights, appear to be all wired to the same relay. Any help/advice is greatly appreciated. Thank you

@MikeZimmermanOfficial 8 ай бұрын

I'm not sure I have the answers for you, but go to troublefreepool.com and ask the folks there, they're great help.

@azvidz5711 8 ай бұрын

@@MikeZimmermanOfficialthank you

@TrueVineSinger 9 ай бұрын

Thank you for sharing this. You gave me the confidence to do it myself and all went well.

@MikeZimmermanOfficial 9 ай бұрын

Easy job for sure.

@keithbriem1147 10 ай бұрын

very nice video Mike! I have the AquaPlus Panel and I had purchased the Wifi Router and Wifi Antenna to get my AquaPlus panel smart. Until I just watched your video, I have recently returned those items on amazon (nearly the same price as the retrofit kit, yikes) and purchased this Retrofit kit and about to tackle this upgrade out in a few days. My only confusion is that I have a Hayward 250 heater currently hooked into my AP panel, I'm assuming it will understand it is there and now manage my heater. Since you don't have a heater, you may not know that answer. I guess I will soon find out. :) thank you again for taking the time to film this, seems easy and well documented.

@MikeZimmermanOfficial 9 ай бұрын

I do have a heater, but it's not controlled through the panel since its not a hayward unit. There were areas where heaters can hook into, and configuration during setup to enable heaters... shouldn't be a problem.

@troycurtis8620 10 ай бұрын

Thanks for the video. I installed one on my 2004 EZGO. It's a nice looking unit and I love having a speedometer on my cart. If the speed is off, you can adjust the default settings to make it more accurate.

@MikeZimmermanOfficial 9 ай бұрын

Good to know! Thanks!

@andrebrooks7040 18 күн бұрын

Is the wire long enough to route?

@199theartist 10 ай бұрын

Is that the only possible sound for a wire finder? :) Why didn't they use crying babies?

@MikeZimmermanOfficial 10 ай бұрын

good question!

@spke532 11 ай бұрын

do you need a new transformer? my current setup works but i need this upgrade. will my current transformer work for me?

@MikeZimmermanOfficial 11 ай бұрын

If you have one, it will probably work. Mine didn't have one which is why I needed to purchase one.

@SmokinLoken 11 ай бұрын

Nice video. Looks like a great speedometer. I like your dash, it looks very clean and well assembled. The only thing I would recommend is to use actual electrical connectors rather than just twisting the wires together with electrical tape and shoving wires in with the spade connectors on your switch panel. Whoever installed the switch panel did a really nice job and it looks professional. I would follow that same level of workmanship to both ensure that wires don't come loose over time and to maintain the quality of work.

@MikeZimmermanOfficial 11 ай бұрын

I did both, I've since cleaned it up but must not have had the parts on hand to do it "right" the first time. Thanks for watching!

@charleschagnon4177 Жыл бұрын

I winterized my 2014 Tige R20 with the same engine as your boat. I did it with the help of your video. I hope everything will be good because it's cold here in Canada Afterward I put prestone through the J pipe and in the cooler of the V Drive. Thanks for your time doing this video.

@MikeZimmermanOfficial 11 ай бұрын

Glad it helped

@ESmith Жыл бұрын

I believe the old board had the transformer integrated into the board and the new one didn’t have one integrated so had to supply it separately

@MikeZimmermanOfficial 9 ай бұрын

I don't know all the specifics, but I think it depends on which version you're retrofitting as to whether it has a transformer or not. The Ecommand did not.

@p33nut Жыл бұрын

I have this. it's difficult to get hang of how to use it properly, it's a skill, bought a IDEAL sure trace for $1200, it's not much better than this, you still need skill to use it, it's almost like an art

@MikeZimmermanOfficial 8 ай бұрын

like any tool, there are different levels. this is lower level. Thanks for watching.

@bradlind7549 Жыл бұрын

Great video and thanks!!!

@MikeZimmermanOfficial 8 ай бұрын

Glad it helped, thanks for watching!

@mbmcmanigal Жыл бұрын

This is a very well put together video with a lot of invaluable information. I really appreciate the time you spent to share this with the world.

@MikeZimmermanOfficial 8 ай бұрын

Glad it helped, thanks for watching!

@drewcoleman7040 Жыл бұрын

Hi so I have an 05 supra you don't need to run antifreeze in that ballast system just un hook everything and your good to go ?

@MikeZimmermanOfficial 8 ай бұрын

Correct... just drain all the water out of the lines.

@ezvue Жыл бұрын

First timer. Thanks for this; alleviated all the uncertainty. Would suggest also doing the following: 1) Remove V-drive water drain plug. A lot of water came out. 2) Disconnect the starboard side v-drive hose, not port side. SBoard side will drain from the impeller. (So you don’t need to struggle with that hard to reach impeller hose). 3) Lastly, run the bilge. 1.5 pails of water were collected. Will reduce chance of mold & mildew.

@ivanyano667 Жыл бұрын

Do you know where the water drain plug for these ZF v drive is? First timer too… I can’t seem to find it, there’s one big plug down there but isn’t that the drain for the trans oil??

@MikeZimmermanOfficial 8 ай бұрын

I dont, sorry.

@NoFlightZone 3 ай бұрын

@@ivanyano667 did you find it? 🤠

@andykolcun8218 Жыл бұрын

You should use waterproof wire nuts!

@MikeZimmermanOfficial 9 ай бұрын

Ope!

@brian5117 Жыл бұрын

Do you have to use the 12v to 5v reducer if you just connect using the USB directly ?

@MikeZimmermanOfficial Жыл бұрын

No, you wouldn't need to if you plug it into a USB port.

Ең жақсы KZbin

Пікірлер