Hey that little fuel filter that hooks up too the bracket at the end of the video does that hookup to anything? Noticed mine is leaking gas from there and not starting
@lucashack53182 күн бұрын
My trailhawk atv won't start 95% of the time. But every once in a while it'll fire right up. Then won't start again for weeks. What could be the reason for that?
@matthewhattia70914 күн бұрын
Ive cleaned my carburetor. When I run the bike, it pops like crazy, literally sounds like fire crackers when I try to accelerate. The revs dip, and then it climbs back and starts popping, repeating this cycle. Should I get a new carb?
@ArcticFrost3 күн бұрын
Have you tried cleaning it out with carb cleaner and compressed air? Also check that the fuel lines are clear and it’s getting good flow. What’s the spark plug color look like?
@dominicsenju8 күн бұрын
I have the same kind but I have problems, it’s like it’s not getting enough power in the wheels,
@ArcticFrost3 күн бұрын
Has it been through water? If the clutch is slipping it’ll feel like there’s no power at the wheels.
@Goodellsam8 күн бұрын
Thank you so much. I thought I would try to find a video showing how to do this on my 2010 550. I didn't think I would find one. What a relief.
@ArcticFrost3 күн бұрын
Glad it helps, hope you can get yours running good!
@mattthon12 күн бұрын
Your knees are close to the bars, frame is small for your size
@shawavsqk12 күн бұрын
I have a 2005 500 arctic cat TRV. I just installed a new carburetor and she starts and idles great. But, after she gets warm she’s missing and back firing and won’t pull herself. Any ideas?
@nicholasellis688913 күн бұрын
Hello! 2008 700 EFI Having an issue with staying running. It will idle fine, as soon as I give it gas it will die. No fault, but checked TPS position and it was on bottom. Adjusted to center. Ran better and stayed running. Next time did the same thing, started as soon as I gave it gas it dies. Checked TPS position again and it was low again. Could that mean bad TPS sensor? Thank you!
@williamzegley227214 күн бұрын
Sweet thanks for the intel. Do you have a video on weak sparking or no spark vr what a good spark should look like, on a 700. God Bless from TN.
@ArcticFrost13 күн бұрын
Sure, you can check the gap on the plug and check the coil wire end and trim it back if the wires are corroded. Normally that will solve spark issues. If you don’t have a spark plug tester you can put it in the boot and hold it to the cylinder head when you crank it you should see if it’s getting good spark. kzbin.info/www/bejne/kJbLon99p96qntUsi=YKBCCcSMDH3qZPxp
@ArcticFrost13 күн бұрын
I trimmed the coil wire and test spark on this ATV kzbin.info/www/bejne/emSWg6Wqe6msmKssi=zBuseAlkjdjenICs
@alexkopytin59514 күн бұрын
Hey man i watched a few of your videos and love them! I do have a question. So i have a 2012 artic cat 700i efi with 500 miles. Itll start and idle fine for about a min, then it dies. I cant get it to idle warm and have to throttle up to keep it running. Fuel is new, i believe i cleaned the injector well. Battery new, tps is centered, atv runs well when riding. Any advice? I searched everywhere and cant get an answer
@alexkopytin59513 күн бұрын
Pleeeeeessssseeee🥺
@ArcticFrost13 күн бұрын
Sounds like the fuel pressure but if it’s riding fine then you may try resyncing the EFI system and checking the throttle cable adjustment. kzbin.info/www/bejne/a57RlGaGdrucnrM
@michaelschecher178315 күн бұрын
How did you access the two screws on the font side of that oil pan? On my 2019 Alterra 700 there is a cross bar on the frame that makes accessing those screws almost impossible. I looks like you lifted the engine up with a floor jack and a 4x4. Did you have to unbolt anything from the machine to make that work? Thanks.
@ArcticFrost15 күн бұрын
It’s kind of a pain to remove. You have to lift the engine up. I remove the front engine mount and the one on the top end, unmount the driveshafts from the output shaft then rotate it up.
@michaelschecher178315 күн бұрын
@@ArcticFrost wow.. that’s a process. Thanks for letting me know. Are they long screws? My thought was drill two holes into that cross bar. Just enough to get the T socket through. Or just let it leak and keep an eye on the levels. Ha. Thanks again.
@michaelschecher178315 күн бұрын
Nvm I saw them in your video. Those screws are too long for my idea to work.
@boondockerstv517915 күн бұрын
Do you have an email for business inquiries?
@ArcticFrost15 күн бұрын
Yep, in my about page.
@jessebaker500715 күн бұрын
So glad I found this channel. My 2017 arctic cat 500 4x4 stalls at idle but runs fine and shows no codes. Will try these tips. Might come back for advice on the belt breaking and the roller weights in the clutch getting destroyed
@ArcticFrost15 күн бұрын
May be your fuel pressure. Hopefully you can get it going again.
@AlexaHome-n3l14 күн бұрын
@@jessebaker5007 Just curious. How many miles do you have on the 2017 Arctic cat?
@AlexaHome-n3l15 күн бұрын
Best channel on KZbin dedicated to the mechanical repair & maintenance of Arctic Cat ATVs. As always another solid video regarding troubleshooting💯
@ArcticFrost15 күн бұрын
Appreciate it! 👍🏼
@troye.130915 күн бұрын
Hello Sir, I have a 2021 Arctic Cat Alterra 700 SE with 198 miles on it. It periodically shows a C1324 code and when this happens my power steering fails to operate. I have to shut the machine off then, turn it back on for it to work. Any help would be greatly appreciated. Thank you.
@ArcticFrost13 күн бұрын
C1324 is the gauge losing connection to the power steering. Could be a loose connector or worn wire causing a short between them. Try replugging the connectors on the EPS and the back of the gauge and make sure they’re fully seated. Hope that gets it working for you.
@FTSsjc16 күн бұрын
I bought one from 2021, still new in store! It comes with Deore 6100 instead, which I prefer over Sram's SX! It's kind of a baby green color though, but because it dates from 2021 I got 30% off. Can't wait for it to come!
@ArcticFrost16 күн бұрын
Sounds like you got a great deal, Enjoy it!
@AlexaHome-n3l20 күн бұрын
If there was an issue regarding fuel pressure, should a 2016 A/C alterra present a code on the diagnostic screen? Want to avoid unnecessary testing.
@ArcticFrost20 күн бұрын
If your fuel pressure was low you’d notice the ATV not starting on the first try, rough idling, dying out/stalling. Sometimes it doesn’t show any codes for low pressure.
@AlexaHome-n3l20 күн бұрын
@ArcticFrost Ok thank you. Is there a diagnostic gadget or tool that I can purchase that I can hook up to my arctic cat atv computer that would show anything or every little thing that may be wrong or going bad on the ATV (e.g. 2016 a/c 500 alterra)?
@WVhillDweller21 күн бұрын
My 2018 alterra vlx artic cat 700 starts up fine and idols fine. As soon as I give it throttle, it starts bogging and won't let me give it gas. If I press too much on the throttle, it shuts off. I checked the air filter, and it's good. I changed the spark plug. It had some black on it, and a tiny bit of looks like oil. Put a new plug-in and still stalling out. What should I check next?
@ArcticFrost20 күн бұрын
Sounds like the fuel pressure. Sometimes they will idle fine but not have enough fuel pressure when you give it throttle. Have you tried resyncing the EFI system? kzbin.info/www/bejne/a57RlGaGdrucnrM
@WVhillDweller20 күн бұрын
@ArcticFrost no, but I will try that. I ordered a new fuel injector. I'm going to put that on once I get it, and I'll let you know if that works. By the way, great videos keep em coming they really help.
@androsborsato21 күн бұрын
Loud valves lol
@rickmoulton633722 күн бұрын
Nice explanation🤓
@ArcticFrost20 күн бұрын
Glad it helps.😎
@esmeraldaestrada6822 күн бұрын
Tengo una 700 4x4 2008 y pero no tiene chispa la bujía
@ArcticFrost20 күн бұрын
Do you have voltage from your coil wire? kzbin.info/www/bejne/aXWZpapuqNt6j9E
@jamesj834823 күн бұрын
Having a similar issue with my 09 700 h1, what did this one end up being? Also the it wont start without jumping the solenoid, even after replacing the solenoid
@ArcticFrost13 күн бұрын
I replaced the fuel pump, injector and solenoid on this one. If the battery is low they will start clicking instead of cranking. Make sure the battery terminals are tight. Does it have good spark and fuel pressure? Any codes?
@troyclench373825 күн бұрын
Have u weighed it ? (Medium)
@GoCards51225 күн бұрын
just ordered one, can't wait
@ArcticFrost25 күн бұрын
Enjoy it!
@GoCards51224 күн бұрын
@@ArcticFrost : )
@robertharrison58526 күн бұрын
no followup video on this?
@paulheiney-y4q26 күн бұрын
THANK YOU, Genius. That saved me a lot of money
@ArcticFrost26 күн бұрын
Glad it helped!
@AlexaHome-n3l28 күн бұрын
Good video. I think the link to purchasing them is outdated but not sure
@AlexaHome-n3l29 күн бұрын
This is very helpful. Especially if you're trying to get an older ATV registered as street legal.👍
@ArcticFrost29 күн бұрын
Thanks. Good to keep your vin written down somewhere when you get an ATV.
@InfamousAMHАй бұрын
Thank you for this video! About to do all 8 boots on my '05 400 4x4. She sat for 18 years outside with only a few hours on the dash and less than 50 miles.
@ArcticFrostАй бұрын
Dry rot can get cv boots. You’re welcome, hope you can get it going again!
@DLuxProdbeatzАй бұрын
i have this code on a 2011 mud pro 1000. when i rev it up, its rev limiting at 3500 and then needle spikes shows this p0500 code. is this a symptom of speed sensor or a different issue? can I jump the port by fuse panel on this bike?
@darrenprocaccini2275Ай бұрын
I have a 2012 Polaris 500 sportsman ho starts up but when I rev it up it Boggs down or dies? Please help!!
@ArcticFrost29 күн бұрын
You can clean your carb with cleaner and compressed air to blow out any particles. Also check your fuel pump is giving the right fuel pressure.
Ай бұрын
tks, very helpfull, JB
@ArcticFrostАй бұрын
Glad it helped. Hope you can get your ATV going.
@NOOB-SUPERCELLАй бұрын
I didnt use my quad for long, then i started her up, running fine, then i accidentally stalled, then she gave the click, i want to replace battery and starter solenoid
@ArcticFrostАй бұрын
What’s your battery voltage? You can get it load tested to see if it still has enough cramping amps.
@xm0rzxАй бұрын
Never get shocked?
@ArcticFrostАй бұрын
I haven’t
@RexHaislip-o1qАй бұрын
Your i5 pro digital camera is very fast frames per second. Excellent buy I hope so. I prefer 85 mph ATV and ride very fast up to the snowing land northward and find goose down sleeping bag. Plus Mod your overstate lighter electric 1200 watts into installation of the greatest ATV deluxe optional factory must install in this convener and entertainment vehicle as like there is recreation ATV for camp out and grill carry up by ATV for hamburger.
@ArcticFrostАй бұрын
Sounds like a great time on the ATV.
@wackiestgravity8857Ай бұрын
Winches. Don’t get buried without one. 🥲
@ArcticFrost29 күн бұрын
We all have that one time without one right? 😂
@alexr6783Ай бұрын
I need help with my atv it’s a 550, battery good, starter solenoid is good. Why is it still clicking?
@ArcticFrostАй бұрын
Does the starter spin? You can apply battery voltage to the positive terminal on the starter briefly and it should turn over.
@wackiestgravity8857Ай бұрын
Are you mostly driving high or low range here? What’s the highest RPMs you can run on your ATV without damaging or causing excessive wear to that engine?
@ArcticFrostАй бұрын
Unless I’m crawling out of somewhere or pulling I mostly run in high. It’s okay to run high RPMs, you just don’t want to hold it at its limit for long time. Running around country roads or getting to trails you can definitely pin it for a bit without any damage.
@wackiestgravity8857Ай бұрын
@@ArcticFrost Thanks! Is 6000-6500 rpm’s too much in high gear range for driving up to 4 or 5 miles without stopping in your opinion?
@ArcticFrostАй бұрын
👍🏼That’s normal on mine
@AlexaHome-n3lАй бұрын
I refer to my atv as "4 wheeler" most of the time. I find having a machete handy is also great for clearing trails.
@ArcticFrostАй бұрын
4 wheeler is what I normally call it too. A machete would be handy, though sometimes the branches are pretty big. But I like not having to carry a whole chainsaw.
@AlexaHome-n3lАй бұрын
@ArcticFrost 🙂👍
@HartRockGarageАй бұрын
Awesome video man
@ArcticFrostАй бұрын
Thanks, hope it helps.
@zita.oraveczneАй бұрын
Hello @arcticfrost! We have an Arctic Cat 700 TRV EFI H1 European quad, registered in Hungary in 2012. My question: Does the ECU need to be calibrated if the injector, MAP sensor and ISC have been removed and then put back in. Problem: Our quad won't start, not getting enough fuel. With a petrol rag placed in a suction hose, yes, until it evaporates. Thank you in advance for your replies.
@ArcticFrostАй бұрын
If you’ve removed any plugs on the throttle body you’ll need to resync the EFI system using this procedure. kzbin.info/www/bejne/a57RlGaGdrucnrM
@zita.oraveczneАй бұрын
@ArcticFrost I did not remove the TPS sensor. In this case, do I still have to do what you show in the video?
@zita.oraveczneАй бұрын
@@ArcticFrostMy atv won't start. I checked the fuel pressure, when I turn the ignition on the pump hums and the pressure is 38 psi and then drops to 35. Is this pressure enough?
@ArcticFrostАй бұрын
You should have constant 43psi fuel pressure. If it drops the regulator or pump is bad.
@kategibson6924Ай бұрын
I sprayed aerostart in and I had my hand on the carb because the choke is broken and it backfired
@ArcticFrostАй бұрын
Did you replace the choke?
@jamesthetannerАй бұрын
I really think Future Motion will have a class action lawsuit for this issue. My front pad in the cold will sometimes not register either side. Sometimes it will at first, but then won't while I'm riding and the board will nosedive. It's become a death trap and I'm unable to trust it. I look forward to seeing Future Motion take a nose dive. They're a pretty negligent company from what I can tell. I question the experience of their engineers.
@ArcticFrostАй бұрын
I switched to the single pad engagement but when it gets cold it’s definitely worse.
@LuisLechuga-vh5btАй бұрын
Do have to calibretation?
@ArcticFrostАй бұрын
@@LuisLechuga-vh5bt on Arctic Cat EFI models you’ll need to sync the EFI system kzbin.info/www/bejne/a57RlGaGdrucnrM
@groupeSaneAutomobileАй бұрын
2,5 L or 3L
@ArcticFrostАй бұрын
2.5L if you’re doing an engine overhaul, 1.9L if you’re just changing oil.
@groupeSaneAutomobileАй бұрын
hello for artic cat 550 how much liter of oil should you put ?
@ArcticFrostАй бұрын
1.9L for an oil change on a 550.
@theprotagonist67992 ай бұрын
If you're 6 ft you definitely got the wrong size frame. The minimum size frame for 6 ft person would have been the large.
@ArcticFrost2 ай бұрын
I had a large first then got the medium. GT’s sizing seems to be bigger than the Nukeproof and Ragley I have that are both size large.
@theprotagonist67992 ай бұрын
@ArcticFrost why return the large how was it too large for a dude 6ft
@lukaszr16002 ай бұрын
Witam moze pomoże koledze z za oceanu z polski. Posiadam Arctic Cat 425 i brak przycisku overdrive jak ściągnąć ta blokade na wstecznym by nie było ograniczenia prędkości.
@keenanhosking6592 ай бұрын
How would you mount a rear winch ?
@ArcticFrost2 ай бұрын
You could either get a hitch mount or have to do a custom made mount to the frame.
@AlexaHome-n3l2 ай бұрын
Will the process you demonstrated for reprogramming the EFI system be the same for a 2016 A/C 500 alterra XL?
@ArcticFrost2 ай бұрын
Yes, the EFI sync is the same for most EFI model Arctic Cats. kzbin.info/www/bejne/a57RlGaGdrucnrM