Everything Engines

Пікірлер

@kg2mb1 5 сағат бұрын

sorry im doing 2 things same time here,important check cam journals inside case and sidecover,back to lunch i go.

@kg2mb1 5 сағат бұрын

one last comment i would replace connecting rod bolts.subscribed hope you figure this out.

@kg2mb1 5 сағат бұрын

Bearing noisy because no oil,apply oil rite after using solvents to clean.

@kg2mb1 5 сағат бұрын

not always the cam why i said to check lash first,now need to figure what happened before dropping a new cam wrecking that one too maby call cam manufacturer welded cam?hmm engine rattling,Noisey?

@EverythingEngines 5 сағат бұрын

@@kg2mb1 I think it was a pushrod issue cause I made my pushrods perfect length with a .060 head gasket on then dropped to a .010 gasket later without thinking about it

@kg2mb1 5 сағат бұрын

ex rocker not lined up.can these rockers be shimmed for better alignment ?

@EverythingEngines 5 сағат бұрын

@@kg2mb1 I’m not sure they didn’t come with shims but I’m gonna take the lash caps off this time around so the tips aren’t as wide

@kg2mb1 5 сағат бұрын

@@EverythingEngines ec rockers?call them first before running without caps..

@kg2mb1 5 сағат бұрын

next time before unbolting head,check lash, make sure valvetrain isnt holding the valves slightly open when Hot because this problem didnt happen for 20mins tells me something hot internally .carb just dosent go out of tune unless fuel obstruction....

@EverythingEngines 5 сағат бұрын

@@kg2mb1 Thanks I didn’t think about that🙏🏼

@CarterCruz-j9r Ай бұрын

Do u need the grinding paste or is liquid fine

@EverythingEngines Ай бұрын

@@CarterCruz-j9r paste is better but liquid should be fine👍🏼

@SpACeCruizeR2o3 2 ай бұрын

What clutch u run homie

@EverythingEngines 2 күн бұрын

Hilliard inferno clutch with black springs

@SpACeCruizeR2o3 Күн бұрын

@EverythingEngines sounds about right good stall

@ogdoubled2837 2 ай бұрын

Clean motor

@privatedata665 3 ай бұрын

I have been a Tech for 42 years . I have some advice . Keep doing what you do . I'm jealous 😃

@robertogonzales-o5r 3 ай бұрын

Awesome video very informative professional To the point . Very bright Young Mechanics

@emmy10110_ 3 ай бұрын

Fire vid

@trymeofficial276 3 ай бұрын

Gaaaas🔥

@jacq-ofalltrades6964 3 ай бұрын

😁

@jvnlyy 3 ай бұрын

Greenstuff is phenomenal!

@trymeofficial276 3 ай бұрын

EBC FTW

@jeffreyodachowski6247 3 ай бұрын

Badass man

@EverythingEngines 3 ай бұрын

@@jeffreyodachowski6247 thanks bro🤝

@jeffreyodachowski6247 3 ай бұрын

Bro your motor still needs a vent its all sealed up put one more vent in the valve cover or just ask some fb predator 212 groups on how to vent the motor you really need a catch can too.

@jayvlog9841 3 ай бұрын

where u buy that adjuster

@camcorderrr 3 ай бұрын

first 🔥

@Goy-wc8od 3 ай бұрын

What's a crankshaft stopper? How do I make it?

@EverythingEngines 3 ай бұрын

@@Goy-wc8od They sell ones on gopowersports Buy one of those that fits a 3/4 shaft and drill a hole that lines up with those holes on the side cover and bolt it together. Use your keyway from your clutch to hold it all together

@waynebatselvlogs1056 3 ай бұрын

yes

@waynebatselvlogs1056 4 ай бұрын

based

@EverythingEngines 4 ай бұрын

@@waynebatselvlogs1056 😂🤝

@emmy10110_ 4 ай бұрын

@trymeofficial276 4 ай бұрын

@emmy10110_ 4 ай бұрын

@Tarzan_Got_U_626 5 ай бұрын

How many cc is that engine? What's your bore size?

@emmy10110_ 5 ай бұрын

Good vid😈

@trymeofficial276 5 ай бұрын

Needs more good dirt😈

@EverythingEngines 5 ай бұрын

@@trymeofficial276 yes it do🔥

@emmy10110_ 5 ай бұрын

Hard asf, good tutorial

@trymeofficial276 5 ай бұрын

Shes running right now👌🏼🔥

@kgol4686 6 ай бұрын

For this kids age he's smart as hell is what meat to say in my last message and a hell of alit better then most of u other wanna be engine builder's keep wrenching brother

@EverythingEngines 6 ай бұрын

Thank you man 🙏🏼🔥

@kgol4686 6 ай бұрын

For this kids engine he's Smart as hell keep wrenching brother you are a lot better then these other wanna be engine builder's on KZbin keep up the good work man

@Jay-fo2so 6 ай бұрын

Good video buddy! New subscriber here.

@EverythingEngines 6 ай бұрын

🙏🏼🔥

@cobster3 6 ай бұрын

Bro can we PLEASE get a 9k rpm revving video

@racingdreamz8021 7 ай бұрын

So what’s considered stage 3?

@EverythingEngines 7 ай бұрын

I’m not sure actually I think just a bigger head like ported and polished head

@Omgvon 7 ай бұрын

w vid buddy

@kyleames3808 7 ай бұрын

Awesome bro!! Keep up the great work 💯🏁🦾🔥

@EverythingEngines 7 ай бұрын

Thank you bro❤️👊🏼

@chuckhuff7123 7 ай бұрын

Good job bud😅😊

@moho2576 8 ай бұрын

U fix the throttle cable or u still steering one handed ?

@EverythingEngines 8 ай бұрын

Wym I haven’t been steering one handed😂

@moho2576 8 ай бұрын

@@EverythingEngines im talking out my ass man, nice video🔥i fw the mini bikes

@EverythingEngines 8 ай бұрын

@@moho2576 appreciate it bro 😎 ❤️

@lamemmb 8 ай бұрын

Do you still have this build?

@EverythingEngines 8 ай бұрын

No I’ve upgraded the head and valve train and pushrods