Is there a way to bypass the reset button to determine if it is actually bad? It feels as if it is a little bit out but it doesn’t go in any further. The quad will not do anything as if the battery is non-existent which I already replaced and I have 12v per meter. Light will come on. I just don’t want to throw parts at it.
@mattlewis73694 күн бұрын
Nice hair
@DMACC365 күн бұрын
Just bought one for my mini bike the other day and it is different from my other engine I was confused on how to start it 😂
@Haloabove18Ай бұрын
I did all this but it keeps slipping
@samuelbrooks8199Ай бұрын
Where did the key go? Do we not use it for this?
@Carlover-qf5vyАй бұрын
My two sprockets don’t align right can someone help please
@michelleminer2190Ай бұрын
Wow! Thanks so much! Does Pepsi work, too?
@TM-xd4vlКүн бұрын
it should. they are very similar
@michelleminer219021 сағат бұрын
@@TM-xd4vl Thanks!
@fangrc3404Ай бұрын
Good vid👍🏼✌🏼
@sysdumb3254Ай бұрын
The belt on mine is too tight I have not been able to get it on
@Eric-fq5wx2 ай бұрын
Did you try a crf70 seat for the rear fender to mount to?
@Chris-ke9ho2 ай бұрын
I've seen a sprocket in the other side of the torque converter plate, anyone know how it's done?
@stephenwalsh81843 ай бұрын
🏍👍👍👍
@Deucealive753 ай бұрын
This is just your idea of "break in" and how you do it. Nothing you showed here is required or needed. $10 a quart oil and an hour of running no load is laughable. If anything, you would want a couple oil changes in the first hour of runtime on these cheap Chinese turds. Unlike other similar small engines, they put a lot of garbage in the oil which is a good reason not to use expensive oil on first run. $4 a quart car oil is all you need.
@bbaaspencer1Ай бұрын
High zinc in the oil on first break in. Ex-racer in the house. 😊
@kurtduff59073 ай бұрын
Why is aligning the keyway important???
@emanuelVargas-yu7rq3 ай бұрын
Hello I ordered a clutch and it didn’t come with that collar or screw to install. Where can I find both?
@gratefulRed693 ай бұрын
Change title to : How to add oil/gas and start a new Predator motor.
@MicahParrish-h3z3 ай бұрын
Pls tell me why i put my clutch on and when i try to go the ckutch just spins and doesnt spin my chain?
@lv.trxpzzz4 ай бұрын
where can i find this clutch or name and collar ?
@ChavaBautista4 ай бұрын
should have power washed it before installing the new plastics
@fangrc34044 ай бұрын
Cool info👍🏼👌🏼
@AbelardoCardenas19724 ай бұрын
Is that a left side for to go for? And a pull start on the right side ? Cuz I'm gonna buy that engine for my minibke just want to make sure first let me know
@seanbrown32514 ай бұрын
What is the thread pitch on the bolt
@Gunther-du4tb4 ай бұрын
What size bolt do I need to use?
@dimasprasetyo31314 ай бұрын
can you tell me about the spesification of the spring on the clucth, how much rpm until the clutch is realesed?
@silasandwesvlogs65954 ай бұрын
Just bought one it’s a 2012 but it sat in a garage in California for all of its life unused so it pretty much brand new and I live in Tennessee so it was a far trip but very worth it
@ToddMeyer-du4wk4 ай бұрын
Wondering if we can chat. I’ve tested everything I can but I can’t even get the starter relay to click Thanks
@lorenzo42p3 ай бұрын
check safety switches, there's usually a few. one on the brake, one in the key, might be another hiding someplace. just follow the wires and continuity test.
@ReikokunaAkuma4 ай бұрын
So you don’t have to tighten the bolt to hard? when I put mine on with a impact wrench it blew off
@markstrad4 ай бұрын
Do you use a steel brush or a brass one? I think that makes a difference with scratching
@cookiesfree64903 ай бұрын
Looks like the brass one I have the same set
@ChristopherAlexisMcGraw5 ай бұрын
Is it normal that my clutch gets red hot and then stops working, I've been told that i should only tight the bolt with my hands but i dont know if its true, I've never tried.
@kaidend.10463 ай бұрын
uhh yea definitely not normal even after riding slow with my clutch not fully engaged and rubbing alot its still cold enough to touch for a few secs without being too uncomfortable
@HoeLeeFuQQ5 ай бұрын
Now how to replace the bearings
@JJ_jake55285 ай бұрын
I didn't get a collar for it
@caseyriojas92734 ай бұрын
I got a clutch specifically the length of my motor shaft and have no issues
@cut.up.parker5 ай бұрын
Is there carbon monoxide and your not supposed to start it up in your garage
@bbaaspencer1Ай бұрын
You’re *
@BennyTheJet87326 ай бұрын
Great video thank you
@gone4none9026 ай бұрын
what clutch is that i'm looking at a go power sports one and i'm trying to figure out what collar to get
@johnsteele80736 ай бұрын
Actually you should be running at about half load to break it in because you need a load on it to seat the rings
@mejustairking81226 ай бұрын
i don’t have the bolt at the end or the spacer
@rogergillette84266 ай бұрын
Is there a way to have the rear shaft extended to right side? I'm looking at converting an E-ton AXL 50cc to a 212, but the chain drive is on the right side of the unit and not the left. My only other option I can see is to replace the entire rear axle with the sprocket on the left.
@robertlewis84646 ай бұрын
Don't use full synthetic oil to break in a motor.
@cameronwilson18155 ай бұрын
Dont use your head too much, you don't have much to use.
@Deucealive753 ай бұрын
That's a myth. No engine oil can stop the rings from seating.
@davidjones20586 ай бұрын
Music to loud
@bbaaspencer1Ай бұрын
Too*
@jamesgilliland22296 ай бұрын
Doing this with cars now
@dylankeepers20646 ай бұрын
You missed any electrical issues mine was the brake switch was bad I just removed it and jumped the wires so no need to set the brake to start
@Dirtthedog6 ай бұрын
Why doesnt my belt align
@heavystarch1007 ай бұрын
Nice video, concise and to the point!!👍🏾
@alekboi40167 ай бұрын
and people ask why I don't drink coke
@robtdougherty7 ай бұрын
@4:37 you are missing the o-ring on the carburetor. Also, you installed the spacer backwards. the o-ring on the spacer should face forward to seal on the intake elbow.
@mexicanbandito7 ай бұрын
Bbbdddrrrrpppppp
@mexicanbandito7 ай бұрын
That petcock is ran off vacuum should be no flow while off
@mexicanbandito7 ай бұрын
There is only on, reserve, and prime
@christophermullikin36887 ай бұрын
Do I need the shim that goes shaft for minibike
@rashaudwalker3527 ай бұрын
That’s funny I have a ds80 Suzuki 😂 that’s why I’m here thanks bro ❤
@perinpowersports96967 ай бұрын
No problem 👍
@carlosesleme7 ай бұрын
thank you Joseph exactly what I was looking for. please keep up with the excellent content. Cheers from Brazil