11 ай бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@tonylamtran 3 күн бұрын
You keep your AP's on a short leash😮
@kugantechfin_wizards Ай бұрын
Can i plug my Aruba Series IAP 325 on this? and how about the configurations ?
@armanshaghi Ай бұрын
Yes you can, but since 1430 is an unmanaged switch you will only have a single VLAN..If you need multiple VLANs have a look @ 1830 series switches instead.
@kugantechfin_wizards Ай бұрын
@@armanshaghi Thank you, I'll look into it. Appreciate the reply.
@HPENetworkingInstantOn Ай бұрын
We always knew the Wi-Fi hunter would be on the case! #HPENetworkingInstantOn
@HPENetworkingInstantOn Ай бұрын
Excellent unboxing! #HPENetworkingInstantOn
@NetworkingDojo_AION Ай бұрын
Thank you!
@TranquiX89 2 ай бұрын
My ssid frequently disconnecting, showing signal 0 speed 0 in console , is it because band interference from neighbor companies?
@danielsan4777 2 ай бұрын
Can you tell me how to physically wire 4 switches for stacking? and which ports do i put on link aggregation?
@stevenschuurman6731 3 ай бұрын
Nice video 🙂 Why do you need to create the Link aggregation uplink on port 24? The stack is already connected with 4 ports and can be seen as 1 switch? Thx Steven
@Joghurt-mit-der-Ecke Ай бұрын
This is no longer about the actual stack. Here, another device is connected to the switch that should be highly available. This can be another switch, for example. However, LACP must also be configured on the other device. If the upper switch fails, the lower switch continues operation without (or perhaps only with a brief) interruption. This is because if you have only connected a device to one of the two switches, it will fail if this switch fails.
@cydia6758 3 ай бұрын
We need a Aruba Instant On Internet Gateway.
@armanshaghi 4 ай бұрын
Boom girl's comedy timing on this one 😂👌
@mattrobinson195 4 ай бұрын
Very cool
@vladasgenys6414 4 ай бұрын
They grow up so fast 😂
@armanshaghi 5 ай бұрын
Epic.
@LiveFree-ij3hn 5 ай бұрын
What if you add a third 1960, do you need to delete the aggregation, rewire then perform link aggregation again? I have the exact same setup. Thanks. Actually using the Aruba Portal since the switch is 1000's of miles away.
@onesmile738 6 ай бұрын
3:42 vlan
@sandeep10k1 6 ай бұрын
Aruba ap 315 green is flashing
@SelvaKumar-yp5ls 7 ай бұрын
How assign ip address each port?
@NetworkingDojo_AION 7 ай бұрын
1830 is a layer 2 switch, it doesn't support routing. You can only assign a single IP address to a management VLAN.
@isuruamalka2258 7 ай бұрын
After the stacking what is use mgt ip.30 or 31.
@NetworkingDojo_AION 7 ай бұрын
In this instance it will be .131. Management address will be the address of the primary stack member after stack has been formed.
@sarahcampbell3570 8 ай бұрын
😂 love this!
@armanshaghi 8 ай бұрын
The joey. Art 🧐👌
@Da_Porkchop_Xpress 8 ай бұрын
HAHAHAHAAHAHAHA! Well done Simpson
@NetworkingDojo_AION 8 ай бұрын
Look out for my new release tonight
@pronettechnologies 8 ай бұрын
Hi Dojo, i have 2 aruba switches 1930, is it necesary to configure trunk port in order to get comunication between the VLANS in the switches?
@NetworkingDojo_AION 7 ай бұрын
yes
@alimackenzie7742 10 ай бұрын
P r o m o S M 😜
@andrearossetti4496 Жыл бұрын
Hi, is it possible to configure a LACP with 2 port of two different switch in stack using the cloud management?
@sutty101 7 ай бұрын
Looking for this answer my-self. Setting up a 3 member stack of 1960's at the moment and I only seem to be able to make a LACP trunk from a single member from the cloud managment. But want it from Conductor and the 3rd member so I can link both to a Firewall LACP trunk for all VLAN's with device reduncancy on the switch side.
@NetworkingDojo_AION 7 ай бұрын
Not at this stage, I believe this feature is being worked on and will be available in 2024.
@timothysnoble Жыл бұрын
What WiFi network scanner are you using in the video?
@NetworkingDojo_AION Жыл бұрын
I've used WinFi (from TethaByte) which is freely available but looks like a recent windows update broke it.
@breakingcustombc2925 Жыл бұрын
I'm assuming you don't have to tag the VLAN's on the stacking ports?
@NetworkingDojo_AION Жыл бұрын
No need to tag/untag VLANs on stacking links when configuring true stacking, all VLANs should be carried by default.
@armanshaghi Жыл бұрын
😂❤
@vladasgenys6414 Жыл бұрын
AP11D is about to mesh:) great job Mark!
@Philmyster Жыл бұрын
haha you're killing me Mark
@ivalleysupport1151 Жыл бұрын
This does not work 100%. There is a bug in the firmware. Stacking works only when using the app, but after switching to local management, it wipes out the stacking configuration. Attempting to reconfigure the stacking as described in this video and after a reboot of the switches, all ports on all switches will start blinking red and never respond. Factory reset is the only way to get the switches back. Perhaps this worked a year ago when this video was released, but at this time, using 1 JL805A (1960 aggregate switch) and 3 JL809A (1960 access switches) connected as shown in the documentation (ring configuration A-B-C-D-A), it does not work without the cloud.😔
@ivalleysupport1151 Жыл бұрын
BTW, this does not mean stacking does not work, it just means you must use the app (cloud configuration) for this to work. Unfortunately, this now creates a possible security hole in the network. Anything accessible in your network from an outside source is a potential security risk. The switches are currently running firmware 2.8.0, which is the latest at this time.
@NetworkingDojo_AION Жыл бұрын
You should only use app (cloud) or local management modes. You are not able to switch between these two without having to go back to factory defaults.
@vladasgenys6414 Жыл бұрын
😂👊
@armanshaghi Жыл бұрын
Wadda rippa! 😂
@tiagoolv5115 Жыл бұрын
do these settings work on the 1830? great video
@NetworkingDojo_AION Жыл бұрын
Hi Tiago, 1830s are not stackable so this config will not apply.
@StephanieHua Жыл бұрын
This switch.... isn't good for enterprise. SNMPv1, Auto-Voice VLAN (Using LLDP), no CLI. amongst other things Might as well buy a Netgear, TP-Link, D-Link.
@NetworkingDojo_AION Жыл бұрын
The Aruba Instant On range is not recommended for Enterprise. It's simple user interface is meant for SMBs or SOHOs.
@JOSERAFAEL403 Жыл бұрын
Can't my vlan to register when i connect the pc. What i doing wrong
@NetworkingDojo_AION Жыл бұрын
Hi Jose, I don't quite understand your setup and your problem. Can you please elaborate.
@tonimardalaba 10 ай бұрын
I have the same issue. I created VLAN 20 and 10 for port 5, but my pc doesn't get the ip from vlan network@@NetworkingDojo_AION
@RavinderKumar-nw5mo Жыл бұрын
How can we configure MAC based authentication for Wireless network in 1930 switch ?
@NetworkingDojo_AION Жыл бұрын
That requires a whole new video
@zorgvxr Жыл бұрын
shesj what power cable if any was in the box ?
@NetworkingDojo_AION Жыл бұрын
It's a country-specific power cord. You can see it at 0:38
@prithwijitde4765 Жыл бұрын
I have deployed mote than 40+ of same,, but none r having 10G SFP one, ur own demo product only shows 1G connectivity
@NetworkingDojo_AION Жыл бұрын
You are correct! Thank you for pointing that out. It is two 1G SFP ports. I've added a correction note and updated the subtitles.
@prithwijitde4765 Жыл бұрын
R u sure SFP ports are 10 G one ?
@NetworkingDojo_AION Жыл бұрын
You are right, these are 1G ports only.
@marlinbriggs985 Жыл бұрын
ᑭᖇOᗰOᔕᗰ
@JasonsLabVideos Жыл бұрын
The Ap25 also uses WAY more power & the RF ouput isn't that high, As soon as you get 10 feet from this ap, the data rate drops by more then half.
@andresinaga9885 Жыл бұрын
So which version of Aruba AP do you recommend for a high-density environment with total clients of 150 - 200?
@milenajanakievska2745 Жыл бұрын
Thanks 😊
@NetworkingDojo_AION Жыл бұрын
Hi Jason, in our testing that was not the case, we were connecting @ the highest data rate at those distances and even further from the AP.
@NetworkingDojo_AION Жыл бұрын
Hi Andre, AP15 and AP25 are for those high density environments, and you may need more than one AP depending what those clients are doing on the network. Wi-Fi works on half duplex principle which means the AP can only serve one client at a time. If the clients are doing something bandwidth intensive like high def streaming the AP will only be able to handle a handful of clients before it runs out of airtime. Having a higher spec AP will help but eventually you need to add more APs (on different channels) to handle the load.
@JasonsLabVideos Жыл бұрын
@@NetworkingDojo_AION Obviously standing beside the Ap25 you will get good speeds, actually mount it and walk away and you'll see its a piece of HOT over priced garbage !
@eprohoda Жыл бұрын
Good day! Yo, that is fantasti c,
@NetworkingDojo_AION Жыл бұрын
Hey, thanks!
@maniraj2678 Жыл бұрын
In our aruba 305 access point connect them limited access only ........how to solve in this problem
@maniraj2678 Жыл бұрын
i tried rebooting and reseting method but in this case not clear
@NetworkingDojo_AION Жыл бұрын
AP-305 is not an Instant ON AP, but and Aruba enterprise model.
@faisalghulam4362 Жыл бұрын
can we manage this switch via CLI.
@NetworkingDojo_AION Жыл бұрын
Aruba Instant ON switches are only manageable via web GUI or Cloud interface. No CLI.
@zoomrsudgrati8176 Жыл бұрын
Can you help me to choose , 10gbase sfp which compatible for aruna 1930?
@NetworkingDojo_AION Жыл бұрын
R9D18A is the SR 10G Transceiver for multimode fibre. J9151E is the LR transceiver for Single mode fibre.
@shmayazuggot8558 Жыл бұрын
So this switch is useless unless one registers online and has an internet connection?
@armanshaghi Жыл бұрын
You can choose to configure the switch locally through the Web GUI (no internet or cloud account required) or through the cloud
@ulunn.k8007 Жыл бұрын
Helo. does aruba type ap 11 support multiple vlan like the one in the video?
@NetworkingDojo_AION Жыл бұрын
It sure does
@eprohoda 2 жыл бұрын
friend.thsi is amazing picture! 🤞
@NetworkingDojo_AION Жыл бұрын
Thanks for visiting
@S30Build 2 жыл бұрын
can i use not aruba ap to this switch
@armanshaghi 2 жыл бұрын
Aruba 1930 Switches support industry standard based PoE+ and other networking protocols. You should be able to power up and set up other APs as long as they are compliant to industry based standards.
@S30Build 2 жыл бұрын
@@armanshaghi thanks, thats what i figured but wanted to check.
@CharlyWu173 2 жыл бұрын
can AP11 be configured without internet connection? does it have local web UI?
@NetworkingDojo_AION 2 жыл бұрын
Unfortunately you cannot. Aruba instant ON Series APs are built to work with AION Cloud to simplify network deployment and management.
@ruslansklimovs9318 2 жыл бұрын
I am trying to build exactly the same LAN where AP11D is connected to ISP directly. But the problem is that my ISP provide me static IP address and thus I never get to the green/amber lights. I can configure it using a DHCP of my current old LAN (ISP- oldLAN - AP11D) but still I cannot find option how to change IP from Automatic to Static - this option in disabled (grayscalled) in WEB menu. Do you know extra options how to connect to advanced options of AP11D?
@NetworkingDojo_AION 2 жыл бұрын
Hi Ruslans, in order to set teh static IP address you need to follow a slightly different procedure. Look at this document: www.arubainstanton.com/techdocs/en/content/get-started/pppoe.htm
@tgottie1 2 жыл бұрын
my aruba 207 has been blinking for 3 days... i would say it is obviously stuck at the blinking green light. i am thinking there is an issue with it syncing its configurations from the cloud. but i am not entirely sure. if someone could please give some insight in this issue that would be amazing! :)
@NetworkingDojo_AION 2 жыл бұрын
Hi there, if the AP keeps blinking green light then it's stuck at booting, you'll need to connect a console cable to the AP to check for boot errors, or try the factory reset procedure. Also check if you have an IAP-207 or AP-207 (controller-based). Btw, it's an Instant AP, not Instant On AP (can get confusing!) :)
@NetworkingDojo_AION 2 жыл бұрын
AP-207 requires a controller to setup and run. IAP-207 will work as a standalone AP, you can configure it locally or through Cloud but you will need a Aruba Central Subscription in order to manage through the cloud. You can refer to our Central videos at kzbin.info on how to setup.
@tgottie1 2 жыл бұрын
@@NetworkingDojo_AION thank you so much for the help! so the problem was that it was either factory reset, or never configured. i was able to connect to it using a default ip and get in through the GUI and get it configured. thanks very much for the help :)