i have a HP DL580 G7 but won't fire up? i have a amber power light and on the little panel there is a red light flashing after i have pressed the power on but no life coming from it whatsoever, could you shed any light on it, i have changed to psu's but still same. there are no other lights showing or flashing i just have amber power light showing and red flashing light thanks
@martinhernes82308 ай бұрын
Hello! Great video(s) this has taken me 1 step closer to my goal. I'm currently working for a company that enables circular IT equipment. We are still building up our knowledge about the devices, and different erasure methods. I've jumped into the rabbithole of Server erasure, and I'm currently stuck at some point. We are running Blancco (erasure software) to erase all our products. I can run this via USB, and it starts up fine. But my issue is that I can't get access to the Blancco Management Console, which is where I get my licenses. Do you have any idea of how I can connect the blades to the network? I tried changing the module from SFP connectors, to Ethernet Passthrough, but then I get an error where the blades are saying they are incompatible. These are PowerEdge M640 Blades btw. I'm just struggling to get the Blade Centre to connect to my network.. Please let me know if you have a good solution for my problem :) Thanks
@Ron-re8hh8 ай бұрын
11 years later... here I am still using PE 2800 server. I'm about to replace the riser card. Do we need to reconfigure the array? I came in to work today to find the server rebooted on its own overnight but it is stuck during POST. Normally I see the following during POST: PowerEdge Expandable RAID Controller... Press <Ctrl><R> to Run Configuration Utility This time, the above message does not show up at all. Server won't boot. I suspect PERC is dead. I'm hoping that I won't have to reconfigure my RAID5 array and reinstall OS after replacing the card. I've never replaced a RAID controller. I hope you or anyone gets this message.
@emmanytube11 ай бұрын
Hi Mate , I have this exact server and was running Truenas , Recently I wanted to upgrade a bit so I added a HBA card , 2x PCIe M.2 SSD and a GTX 1660 super ( for plex transcode ) . Now the server fan is at constant 33 - 50 % and its quite noisy in the house . If I remove the PCIe devies , the fans are back to 13% and very quiet . Is there any way to get the fans go quieter ?. Cheers . Emmany
@StuffJason4374 ай бұрын
Hardware without a HP certified sticker will cause the server fans to increase, as the fan controller onboard doesn't have a fan profile for that hardware configuration and as such you will need to install custom ILO and then manually tune the fans.
@CAXRAMEDIA Жыл бұрын
Useful video. Thanks sir
@nohvoha6058 Жыл бұрын
Thanks for the guide
@jfkd28122 жыл бұрын
Uh, on my T710 the indents are there, but the holes are not threaded when I'm installing the rack ears.
@techwikisl3 жыл бұрын
Great Video
@zachhansen22713 жыл бұрын
wow that computer server is so hot and cool it makes sounds that remind me of my prepubescent anime waifu uwu
@CmmdrKitty3 жыл бұрын
Just got one, Has everything except the drives. Not sure what to use it for
@DEV_Shadow3 жыл бұрын
how is nice to see how you look at some piece of paper and read this server can much more than you have on this piece of paper :)
@piotrlenarczyk58033 жыл бұрын
Thank you for video.
@Eduardosantos-nh2ez3 жыл бұрын
Good evening friend I hope you can help me, I recently acquired this server and is giving the following error (pcie built-in bus error # 00 / dev # 02 / func # 0) can you tell me what it can be? Please!!
@jagdishgaikwad48203 жыл бұрын
Here creat new vd is disabled... Plz guide
@RobertBullock3 жыл бұрын
I'm using a T310 for a home NAS/Docker machine. Is there any point to an iDRAC for me? Still new to the Dell PowerEdge game and it looks like there isn't. My build: kzbin.info/www/bejne/b33bm4euipJgn6s I have 7 drive bays now. :)
@davkas193 жыл бұрын
iDrac express will allow you to remotely power down (Full shutdown) and power on your server if you had to for some reason (Think hung server where you need to hard reboot). You can also use it to virtually connect to the server (Think RDP) to the server and enter the bios, raid, or integrated services and makes changes. It allows you to remotely manage the server as if you were standing in front of it as well as a host of other features. iDrac express allows you to remotely manage the server up until an OS has load and is at the login screen. iDrac enterprise would allow you to actually login to the OS and do everything as if you were standing in front of it. So if RDP stopped working on a server or you screwed up the NIC settings and couldn't connect to it via RDP, you could still connect to it via idrac and login and fix whatever you broke, as idrac uses it own IP separate from the main nic.
@fulgore19303 жыл бұрын
hello im miguel i have a dell 2950 whit error /e1000 E1228 0.9v PwrGd you know solve it?
@douglasblatt16423 жыл бұрын
Is it possible to replace the motherboard with a completely different one with newer components and card slots? Would any ATX motherboard work in this case? I like the case, but want to upgrade to something that allows for new video connections (or a video card).
@douglasg14b3 жыл бұрын
Note that these run on 110v just fine
@doomgod3144 жыл бұрын
I’m trying to find out what Version of PCI slot this thing has. The support.hpe site isn’t clear if they come with the pci x 64bit or not. Just trying to connect the best possible gpu I can. Thanks for explaining man. Great video.
@mrwild84 жыл бұрын
6 1/2 years later - still useful! I have one of these as my Home server now and it suffered a Lightning hit in my house. Lost Mobo and PERC controller card. Got another off eBay for $150 shipped and was able to swap from the eBay damaged case, YAY!!!! And Yes, it did take just a little bit longer - I was so surprised it was THAT easy!
@darioushnassiri11974 жыл бұрын
The server has 3 usb input, can u explain how can l connect the 4th usb device, thank you?
@conraadvandenberg4 жыл бұрын
It has an internal USB port as well.
@bijukcy4 жыл бұрын
Thank you so much for creating this video!
@honestreview90194 жыл бұрын
hi i need ur help. i have connected a usb keyboard, mouse and vga monitor to the front panel of the m1000e chasis. when ipress print screen nothing happens i dont get this window to go through the blades and select. Tried on back panel too on ikvm switch but same issue.
@velocitytechsolution4 жыл бұрын
So the first thing I would do is look at the rear of the chassis and look at the iKVM. Is the top led green? Aso, look to see if the amber warning led is lit up. Try reseating the iKVM module and see if that helps. If still nothing comes up I would expect the iKVM module on the rear of the chassis is dead. Simply replace the iKVM module and it should start working again.
@honestreview90194 жыл бұрын
How to reset the ikvm just pull module out and out in?
@GaryVerderamo4 жыл бұрын
I could be wrong, but that didn't seem like an ESD safe surface. I distinctly noticed the absence of an ESD wrist strap. Yeah. I know. People just touch the case. However, with something as expensive and mission critical as a server, why risk it?
@Animalwon4 жыл бұрын
I have the Power Edge SC1420 and you have the 1430. You didn't mention the socket used for your CPU'S, What are they? Are your cpu sockets the same as the Cpu sockets on mine?
@Animalwon4 жыл бұрын
When you replaced the CPU Heatsinks, I noticed you didn't apply any thermal compound. Did the heatsinks already have heatsink pads pre-installed? Or was this "heatsink install without thermal paste" done by mistake?
@intel386DX4 жыл бұрын
How to do the opposite use redundund power supply to a standard motherboard
@PatrickChapmanuk4 жыл бұрын
I know this is an old video.. But I'm seeing these systems go for a song lately. If you have the time, what's your opinion on their use for today?
@generalsifr29952 жыл бұрын
you can still use them for labs. I just got one and it was just pulled out. I actually got two of them one gen 9 ml 350 and 350p. Strange this is that the gen 8 got more memories and two cpu and gen 9 got only one cpu. Gen 9 was DDR4 and I want to use it for virtualization so I ordered rams on ebay. I will make a video shortly.
@TheBlueScreenYT14 күн бұрын
I’m getting one tomorrow for free, I can let you know what I find out
@gabirican48134 жыл бұрын
Awesome, very helpful. Thank you.
@aksharjamgaonkar16774 жыл бұрын
Hi, can you please also create a vidoe for installing a NVMe M.2 SSD?
@MrPacman644 жыл бұрын
i mean its pretty much plug and play. there are also a billion videos already on it
@louisp524 жыл бұрын
I dont expect this to get answered, but do you have to buy the backplane cables, or are they preinstalled
@TheDogcatchersito3 жыл бұрын
You will have to buy them
@dudley2374 жыл бұрын
how do you replace the failed battery in the Dell PowerEdge M1000e Chassis Management Controller? It is running on the Passive/Secondary but the active went out.
@drothers9994 жыл бұрын
Can the Dell PowerEdge 2950 function without the RAID card?
@velocitytechsolution4 жыл бұрын
Yes, if you don't set up RAID.
@cwetdog4 жыл бұрын
I have the server thinking about tricking it out wonder what it would look like with liquid cooling
@poulette29374 жыл бұрын
why does it have 18 ram slots then ? I want to buy one of those but did he make a mistake when he said you cant use all 18 slots with R dims or are 6 of them actually useless
@Hotboll14 жыл бұрын
cuz 2 cpu's. u can use all 18 slots
@saadatsaeidi63545 жыл бұрын
can I ask , if you have the pin out (Pin diagram )of the PSU ?, I need to change the configuration to start the power supply(.Dell PowerEdge M1000E 2360W Power Supply 0C8763 C8763)
@yulmerced44345 жыл бұрын
how can i get the 1333 speeds? tried a few different rams and i can still only get 800
@prisondude5 жыл бұрын
Want those shoes
@MATB00KER5 жыл бұрын
Power still connected and no static protection 🤦♂️
@petersonmlp5 жыл бұрын
Thank you Mike. My name is Mike. My employee is Mike and he battled this system for an hour. It all came down to the BLUE BUTTON!
@dineshkr995 жыл бұрын
I need to access it from data center ...not from remote how can i do it
@mety93255 жыл бұрын
the server does have a 75w external power supply for GPUs...
@Mike_Jones2815 жыл бұрын
Wait! Only x8 and x4 PCIe slots? Nah.
@dirk6005 жыл бұрын
Hey man! i want to convert my dell T610 from a rack mount into a Tower, would you sell me the fancy plastic bits! Seriously!
@jcc1894 жыл бұрын
dirk600 are you still looking to do this? I want to convert my tower T610 to a rack and need the side mounts and rails
Hey guys, I'm trying to install a GTX 1080 Ti in this same server but it doesn't work. I replaced the power supplies for 1200 Watts and the card lights up but after a few minutes it says "Please power Down and Connect the PCIe power's cables for this graphic cards". I tried everything but it always come with the same result. Thank you !!
@velocitytechsolution5 жыл бұрын
Hi Alex, Thank you for watching our video and reaching out to us. Given the error is referencing the power cables do you have the additional video card power cables that would come from the motherboard and plug into the card? Unfortunately they aren't standard on the system so you would have to buy a kit which now appears to be fairly rare. The kit part number is 660582-B21. Let us know if we can help with any other questions. Thanks again Velocity Tech Solutions
@the_sneakers_patron35615 жыл бұрын
Yeah i contacted HP about that Kit, it is very hard to find, hopefully a kit for the 9 gen can work on this!!! Thank you for replying :D
@HotNoob5 жыл бұрын
@@the_sneakers_patron3561 you can modify a modular cable to work. two of the pins are different. you can either rewire, or just cut those two wires and it should work. best to rewire.
@joshuamongardini56044 жыл бұрын
@@HotNoob What are the two wires you refer to cutting? I assume in terms of the 8-pin connector cable between the GPU and the motherboard. Thank you in advance, much appreciated.
@HotNoob4 жыл бұрын
@@joshuamongardini5604 should be pin 4 and 8. or just pin 4. dont remember 100% off the top of my head. if you grab a volt meter you can just test each pin individually. your aiming for 12v on one side and ground on the otherside.
@shahzadhaider91955 жыл бұрын
I have the same server, very good option, but too noisy.
@dinamarcalibre37965 жыл бұрын
and the ram?
@stevearkwright3 жыл бұрын
2 x Banks of 8 slots - max.128GB - PC2-5300P (Parity)
@Slipdrive5 жыл бұрын
Can you PLEASE make one of these full breakdowns for an R530 and possibly a 2950 ??? I've been looking for this exact type of video for the R530 my company bought from you guys a couple weeks back. BTW - to anyone from a SMB that see this... These people are FANTASTIC. Quality materials; superb service.
@Maisonier5 жыл бұрын
I don't want just to replace, that is very easy ... we need to know how to repair the System Board, is a really expensive part.