My honda accord power steering bottle is always full of grease i check not bubles , feel like is coming from bottle cap . Please answer

One of the best videos I've ever seen. Thank you

Hello, went through the carb, great video thank you. Put back together and it started right up. Sputters when I get on it at about 30mph. Long story short pulled petcock and the screen filter was rotten and broke off into the tank. So been "rinsing" the tank with fuel and filter screens. Lots of debris. Rinsed with about 12 gallons of gas and still debris comes out. Is there a faster way? This will take forever. Thank you. 2005 Honda VTX 1300.

Outstanding video! This exactly what happen to my daughter's car and I thought for sure I would have to replace the entire cable. Thanks for the helpful info!

If you stills replying I have one question. Do you have to burp it with the tank off?

This has been the best video so far for helping a noob. Thank you so much for that. Question. 2005 Honda VTX 1300 R; The carb adjustment was almost 2 turns from closed. Technically about 1.85 turns. It is super cold when first started. Takes 10 minutes of not so smooth idling to warm up. Should I set it at 1 1/4 to 1 1/2 turns from closed? Also I saw the part about the stronger spring on the choke. Could that be some of the problem? Thank you.

Good video. But can you include in the title the year model and the engine size ? Thanks

Is this the same part for a 2013 cx5?

This is all wrong!!! Dont follow this terrible video

Thanks bro.... It was very helpful

What an amazing job done brother. Thank you 🙏 for sharing. God bless You and your family!

Thank you for your video it was very well done.

Thank you very much for being so detailed on the steps to take to replace the parking switch. I had to replace the switch on my mazda 6 and this video was a huge help.

Is the mode actuator different from 4 and 6 cyl? Thank you

Thanks, same procedures in CX5 2.0 L model?

Sir i have leaking oil from bigger pipe at juction of power steering reservoir junction(same leakage location as your car shows in video) , company tells its hydraulic system problem leakage is it possible that i change pipe and reservoir and prevent power steering fluid leakage?

Question, im thinking on going darkside on my 03 vtx1300s and is your tire the bigest size you can fit 205-70-15 is what i believe you have? if so do you notice a difference on cornering ?and do you like the michelin? thank you!

Thanks for your help

Thanx was able to replace mine only took a few min hardest part is to line the bulb up and put it back in

Thanks for the video. Replaced my tensioner at 100k. Couple of tips from my experience. A simple plastic grocery bag twisted to make a rope, works great to pull off water pump belt. The new tensioner takes a lot more force to compress than 100k mile tensioner. Thus you need to use the two wrench method extra leverage to get the new tensioner to get it to move, as shown in video.

Valuable Video!

Anyone that has used the heat shrink tubing is it still holding and or how long did it hold for?

Great video , thank you.

Very helpful. Thanks!

In normal state should shake or not .??

I went to your video for a refresher too. I’m a 64 yr old female and changed it the first time maybe 14 yrs ago? My husband is handy but I like to do some things myself. I still had the second bulb in the blister pack. The hardest part for me was getting the bulb socket back in. I only lifted the gear plate just enough to get my fingers in there. I have a 2004 Honda accord lx, 338K and still runs great! Original engine and transmission.

Great tutorial! Good job with the clear video and steps!

Thanks a million. Worked for me. You are kind to share 🙏

What if I'm needing to replace the lower control arms? Where do I place the jack stand?

My radiator fluid is leaking from underneath the bike at the Overflow do you know what that is doing or why it's doing that

I struggled with the water pump belt for about 3 hours as I could not get it around the the smaller diameter water pump pulley cover sufficiently to feed it onto the pulley. Finally set it on the water pump pulley and set the belt on the crank pulley and zip tied it in place and cranked it on slowly directly into position. The belt came out of position on the water pump pulley but tight onto the front cover. From there I twisted and pushed the belt while cranking very slowly until the belt caught the lip, then slowly walked it over twisting and pushing with a 1.0" wide stick and voila, done in 40 minutes.

Should change those rubber gaskets too after 10,000 miles while the tires off ,think theres two of them one on the cupler and one on the rim .

all videos seem too prefer pro jet kit other kit makers seem too give people problems if anyone is interested thanks for in depth video

best video ive seen

Love these vids. But really the pass side is impossible right? I did the drivers but am balking on the pass side.

Hey bro so I’m having something similar to this with my vtx1300 2003 I just got a brand new battery and it has been doing good these past 2 days till I was trying to go to the store and it wasn’t turning over just clicking and made it seem the battery was dead so then I waited a little and after that I tried once again and it turned on like nothing?? What could my issue be??

Are the tanks interchangeable between the 1300r and 1300c?

Mine moves as far as it can go, when my compressor kicks on. And it really robs power from the motor.

What size socket you need to turn the crank pulley? I dont have a complete kit so I need that one socket. Thanks

Excellent Will be doing soon as I believe the tensioner is causing my alternator to not fully charge my battery

When you were draining the radiator from that valve did you get all of the coolant from the system or only a portion and if only a portion, how much of the overall radiator capacity did you drain out?

thank u for this

You can’t get Honda 60 moly paste anymore. The equivalent (actually better than Honda 60 Moly) is Loctite LB 8012.

Hey man thanks for the video I always love your content very concise well-spoken has always helped me with my beloved Astro

Well done👍

Great vid; thanks

Why can't we use the jack stand in the same spot we used the jack floor to lift the car?

Good job!

You're an a****** yeah that's what it's doing Now how do you fix it a******

Is it OK to use DOT 3 brake fluid from an auto store or should I buy it from Mazda?