6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
Пікірлер
@tarritaylor1444 12 күн бұрын
Hey
@chrisdavis9556 12 күн бұрын
@@tarritaylor1444 yes
@yasoutherncousin 15 күн бұрын
Does the harmonic balancer signal plate has to go back on in the same spot?
@chrisdavis9556 14 күн бұрын
@@yasoutherncousin yes
@MrDeticus 2 ай бұрын
Will you come to my house in Virginia? I have been fighting this today and it has made me furious.
@chrisdavis9556 2 ай бұрын
@MrDeticus lol that's over 2000 miles away .
@garzacano 5 ай бұрын
2022 ford ranger 2.3 do you have a part number for the timing tool kit?
@Joepellegrino-dv4mh 6 ай бұрын
I have a 2010 fusion. Isn’t there a special diamond washer behind the harmonic balancer that needs to be replaced? And should the bolt also be replaced?
@chrisdavis9556 6 ай бұрын
yes the bolt comes with the washer
@TimothyWhitt 7 ай бұрын
I have a 2015 Ford focus and I think I might of messed up changing the harmonic balancer pulley without special tools any help or advice
@chrisdavis9556 7 ай бұрын
get the tools and pray you didn't bend the valves
@anthonyfrank5430 7 ай бұрын
I was quoted 1300 to replace two lower ball joints on my 14' 2500. It's a ripoff huh
@chrisdavis9556 7 ай бұрын
about 3 to 400 dallors to mich
@chrisdavis9556 7 ай бұрын
to much lol
@elijahsandlin9461 8 ай бұрын
The balancer does not control mechanical timing if you tighten it down without lining it up correctly it will only effect ignition timing.
@chrisdavis9556 8 ай бұрын
there is no line up pin . the motor will spin and yes mechanical timing will be off.
@briankennedy3523 10 ай бұрын
Mine is basically welded in ,not coming out😂
@chrisdavis9556 10 ай бұрын
heat it up with a plumber torch
@biffjunior8995 10 ай бұрын
Hey, i am pretty mechanically inclined but I've never messed with timing in anyway. I have a 2.0 duratec focus and im pretty sure i have a bad harmonic balancer. Its kinda wobbly, and im getting an engine "whine". Anyways, i cant find any videos on my specific model to replace just the crank pulley. But, i have found a bunch on changing the timing chain. Do you think i could use those videos on timing chains as kind of a guide to change the crank pulley without messing up timing? Thank you.
@ljaymaster Жыл бұрын
What does just replacing balancer normal cost to have done?
@chrisdavis9556 Жыл бұрын
350. depending labor cost
@ljaymaster Жыл бұрын
I have questions
@chrisdavis9556 Жыл бұрын
what's up
@ljaymaster Жыл бұрын
@@chrisdavis9556 I'm driving at the moment but will explain the situation this evening
@mighandball13 Жыл бұрын
Tdc number 1 align balancer to the hole thats it
@chrisdavis9556 Жыл бұрын
call me 817-449-3332
@HeatherPennington-xc3dj Жыл бұрын
Can this method be used for 2018 dodge 2500
@chrisdavis9556 Жыл бұрын
for the most part it should
@Mega7492 Жыл бұрын
Why would you not shine up and lube those holes with antiseeze ?
@Bayzhit510 Жыл бұрын
Quick question i replaced the timing cover gasket on a 2016 ford transit connect xl with the 2.5, but i didn't touch the timing at all i didn't even put it on tdc, but when i removed the harmonic balancer i market it with a market and put it back i haven't started it but what do u think ? Im a mechanic i just haven't worked on any of these engines b4
@chrisdavis9556 Жыл бұрын
bad move still maybe out of time
@jamesworsham2312 Жыл бұрын
What does stupidest shit I ever seen yay Ford you screw us again I suggest that they recall all these motors and at least put a dowel pin or keyway in the crank and then put a notch in harmonic balancer every damn car ever built harmonic balancer and or crank keyway only one way installation but no Ford had to screw us again I got me a brand new 20 lb sledge hammer take a ride to see Ford engineers and give them a love tap or as we call it whack fuck
@brianangelhoyos8428 Жыл бұрын
What's the name of the press kit or #
@guille20089 Жыл бұрын
Hello what’s advise Can you give me if i pull out the harmonic balancer with out locking it put the new one and start the car and car won’t turn on now?
@chrisdavis9556 Жыл бұрын
Yeah you have to have the tools to time it or no start . If you need to talk through it I'll send my number.
@guille20089 Жыл бұрын
@@chrisdavis9556 thank you very much Chris I would appreciate that I got the tools now I just didn’t had them before. One more question can I reuse the bolt?
@chrisdavis9556 Жыл бұрын
@@guille20089 yes
@chrisdavis9556 Жыл бұрын
817-449-3332
@guille20089 Жыл бұрын
@@chrisdavis9556 when is the best time to call you?
@KNCRKNCR-if9uf Жыл бұрын
So I have to buy specialty tool to tighten the crank bolt and harmonic balancer
@KNCRKNCR-if9uf Жыл бұрын
?
@chrisdavis9556 Жыл бұрын
I used a chain wrench to hold the crank pulley.
@MarySiebert-fk5ot Жыл бұрын
I did everything I was supposed lined up using the pin turned the crank til it stopped took valve cover off put cam alignment tool everything was perfectly lined up put back together lined up wouldn't start turned over fine so I took back apart and lined up everything perfectly again pulled off harmonic only difference I see is the newer harmonic balancer ring has more teeth and smaller than the original could that be the cause?
@chrisdavis9556 Жыл бұрын
Yes . It must be the same one . If not it won't start.
@MarySiebert-fk5ot Жыл бұрын
@@chrisdavis9556 the harmonic balancer look identical except for ring in the back the original had 35 teeth the one I have has over 40 still trying to figure out what the ring does I think it gives a signal to the crankshaft position sensor?
@MarySiebert-fk5ot Жыл бұрын
So the more teeth would give a wrong signal ?
@chrisdavis9556 Жыл бұрын
Correct.
@MarySiebert-fk5ot Жыл бұрын
@@chrisdavis9556 thank you because it definitely sounded like it wasn't firing
@MarySiebert-fk5ot Жыл бұрын
I see that crank pulley broke the one on mine is making a loud rattle noise at idle goes away at acceleration so even if I'm just changing the crank pulley and not doing a timing job I still need this tool?
@chrisdavis9556 Жыл бұрын
Yes
@highlive2166 Жыл бұрын
THANK YOU!!!
@JamesTener Жыл бұрын
I removed harmonic balancer without marking its' position. I took the cover off and resealed it. How do I determine the position of the pulley when I put it back on? I don't know the engine cylinder position.
@DM-lf8bn Жыл бұрын
Wow! Thanks for this. You make it way simpler than others.
@sorryimajerk735 2 жыл бұрын
MAN THAT WAS A ROUGH SHOW TO SEE YOU USE THAT BJ PRESS MAN HOLY FUCK ID ERASE THAT SHIT
@victorvargas1062 2 жыл бұрын
What if you get out without knowing you need special tools
@mikelarry8409 2 жыл бұрын
What the name the tool I need to hold the crank in place do it come with the bolt to hold the crank in place
@chrisdavis9556 2 жыл бұрын
Go to Amazon and look up ford 2.5 timing tool kit. I tried to clip a pic to show you.
@chrisdavis9556 2 жыл бұрын
It's a 3 piece. And at the bottom they have bought together as well about $100.00
@fj5gtx770 2 жыл бұрын
I used the small piece that you used for the top joint, got fused to the ball joint - having a really hard time getting that piece off the joint ! Thinking use the large one first, get the joint moving - then move to using that small piece to finish it off.
@brendaleetv 2 жыл бұрын
Wow! I just broke 2 ball joint presses! Trying to take off the driver's bottom ball joint. On a 2006 Ram 2500 4x4, I just bought a Makita corldless 1,200 lbs of unbolting power and it didnt even move, so now I think I broke the impact, but its new so its still under warranty.
@tobysirus4996 2 жыл бұрын
You really have to ensure the cams are in the correct location .Use cam alignment bar it will only fit one way.That bolt will slide threw the damper and screw into the block with the cams in the wrong location . Tightening that damper bolt 30 lbs,75lbs then an additional 90 degrees showed me how old I really am. That a real ball buster !
@rmarty9907 2 жыл бұрын
What was your tool make and model number?
@chrisdavis9556 2 жыл бұрын
It was the one you get at O'Reilly
@RichardRLeal 2 жыл бұрын
Don't EVER use a pair of pliers to turn the crackshaft! That's cutting it up.
@chrisdavis9556 2 жыл бұрын
Only if you use heavy force.
@kalebdarius3921 2 ай бұрын
Not that serious. Done it many times. It’s not a sealing surface so no worries
@nonsequitur807 2 жыл бұрын
It would make better sense to show the set up than the frigging impact tighting...
@luiscordero2505 2 жыл бұрын
No
@markdavila5297 2 жыл бұрын
What happens if you take off the pulley wrong without putting the special tool in the back and you already cranked it
@chrisdavis9556 2 жыл бұрын
Won't start
@markdavila5297 2 жыл бұрын
@@chrisdavis9556 I have to put the harmonic balancer in rite timing with the tool ?
@chrisdavis9556 2 жыл бұрын
Yes
@markdavila5297 2 жыл бұрын
@@chrisdavis9556 thanx
@H3LLMAU5 2 жыл бұрын
Today I removed the crank pulley without installing the service bolt or locking the cams in place, since then I haven’t touch the engine, you think I might have damaged the engine?
@chrisdavis9556 2 жыл бұрын
As long as you haven't started it you can still set ti timing
@H3LLMAU5 2 жыл бұрын
@@chrisdavis9556 no I haven’t done anything other than just removing the harmonic balancer
@chrisdavis9556 2 жыл бұрын
If you haven't gotten the timing kit Amazon has it cheaper.
@chrisdavis9556 2 жыл бұрын
$14.00
@arturomagana7587 2 жыл бұрын
The pulley was removed without putting the bolt to CK your timing would that be an issue
@chrisdavis9556 2 жыл бұрын
No as long as you set the timing bolt in the side of the block you are ok
@kccarl2582 3 жыл бұрын
great video!!! thanks for posting. using video on install now. lol put a bungy strap on that brake caliper!!!
@chrisdavis9556 3 жыл бұрын
Lol I replaced them
@maestromania3391 3 жыл бұрын
Thank you for posting this video. Saved me lots of time & money!
@chrisdavis9556 3 жыл бұрын
You are very welcome
@terrellscaife2411 3 жыл бұрын
Awesome shit
@styleauto1025 3 жыл бұрын
Great vidéo help alot
@thomassmith2739 3 жыл бұрын
I have a 2011 ford fusion and my car cranks up but wont start i just recently changed the harmonic balencer what could it be
@chrisdavis9556 3 жыл бұрын
Sounds like it's not in time
@musclepharm867 3 жыл бұрын
Where did you get the ball joint press is there a certain kind to get? Would the harbor freight 4wd press kit work on these dodge 2500 diesel trucks?
@selimyenahc3184 Жыл бұрын
Did it work? About to pull the trigger as well.
@aaronstivers7708 3 жыл бұрын
Do I need to remove the valve cover and use the cam locking tool or just the bolt. Only replacing Harmonic balancer
@chrisdavis9556 3 жыл бұрын
Yes you have to . Plus the crank locking bolt you must do the hole thing no choice
@SamSung-tv8jr 3 жыл бұрын
I have my tdc pin in and my cam plate in now I need to kno what tooth from the tdc hole or were I need to put the crank sensor
@SamSung-tv8jr 3 жыл бұрын
I'm replacing head on 2014 ford focus se 2.0 trying to get my harmonic balancer and crank sensor align
@chrisdavis9556 3 жыл бұрын
Sorry I haven't responded. If you haven't finished there is a small bolt hole on the balancer that bolts to the oil pan. That's your line up.
@robertleavell712 4 жыл бұрын
Can the. Harmonic balancer effect shifting in a transmission
@chrisdavis9556 4 жыл бұрын
If its off timing it can
@robertleavell712 4 жыл бұрын
There's whining when I start it up can't figure out if it's alternator ,a pulley or balancer any suggestion ,or tips. 2014 ford escape
@chrisdavis9556 4 жыл бұрын
Take the belt off start it see if it goes away. If it does . Spin all the pulleys see if any are rough. And check belt for cracks or oil soak.
@jesserivera1383 4 жыл бұрын
96 f350 dually harmonic pulse plate spin. Can't seem to find them. Need help.
@chrisdavis9556 4 жыл бұрын
What motor do you have?
@jesserivera1383 4 жыл бұрын
@@chrisdavis9556 hi Chris, it's a 7.5 liter xlt
@chrisdavis9556 4 жыл бұрын
I looked at engine diagrams and didn't see that part you have a picture of it?
@scottcraig1047 4 жыл бұрын
I wouldn't use channel locks on the crank snout.