Ford 2.5 harmonic balancer pt2.

[@scottcraig1047]

I wouldn't use channel locks on the crank snout.

[@tobysirus4996]

You really have to ensure the cams are in the correct location .Use cam alignment bar it will only fit one way.That bolt will slide threw the damper and screw into the block with the cams in the wrong location . Tightening that damper bolt 30 lbs,75lbs then an additional 90 degrees showed me how old I really am. That a real ball buster !

[@biffjunior8995]

Hey, i am pretty mechanically inclined but I've never messed with timing in anyway. I have a 2.0 duratec focus and im pretty sure i have a bad harmonic balancer. Its kinda wobbly, and im getting an engine "whine". Anyways, i cant find any videos on my specific model to replace just the crank pulley. But, i have found a bunch on changing the timing chain. Do you think i could use those videos on timing chains as kind of a guide to change the crank pulley without messing up timing? Thank you.

[@J1TORCIK]

Good video, removing the crank pulley question. What are you using to hold the crank in fixed position while removing the pulley? Are you just relying on the cam positioning bar? And or the small bolt in the bottom of the crank pulley? Thx

[@chrisdavis9556]

I was using a chain wrench

[@J1TORCIK]

@@chrisdavis9556 I think I will try that before trying the bump start method. Do you use an impact with the chain wrench?

[@chrisdavis9556]

Put the small bolt in the pulley. Put the chain wrench on and i used a breaker bar to tighten down no impact.

[@J1TORCIK]

@@chrisdavis9556 Thanks a bunch. Sorry for the seemingly dumb questions. My dad was a tech, gives me the can do confidence but a retirement from financial services leaves me lacking much tech knowledge. Many kiddos for answering, so many other youtube stars aren't as attentive. Be well and thanks again!

[@JamesTener]

I removed harmonic balancer without marking its' position. I took the cover off and resealed it. How do I determine the position of the pulley when I put it back on? I don't know the engine cylinder position.

[@yasoutherncousin]

Does the harmonic balancer signal plate has to go back on in the same spot?

[@chrisdavis9556]

@@yasoutherncousin yes

[@garzacano]

2022 ford ranger 2.3 do you have a part number for the timing tool kit?

[@Joepellegrino-dv4mh]

I have a 2010 fusion. Isn’t there a special diamond washer behind the harmonic balancer that needs to be replaced? And should the bolt also be replaced?

[@chrisdavis9556]

yes the bolt comes with the washer

[@Bayzhit510]

Quick question i replaced the timing cover gasket on a 2016 ford transit connect xl with the 2.5, but i didn't touch the timing at all i didn't even put it on tdc, but when i removed the harmonic balancer i market it with a market and put it back i haven't started it but what do u think ? Im a mechanic i just haven't worked on any of these engines b4

[@chrisdavis9556]

bad move still maybe out of time

[@edgargarcia8627]

Very good information thank you so much

[@mikelarry8409]

What the name the tool I need to hold the crank in place do it come with the bolt to hold the crank in place

[@chrisdavis9556]

Go to Amazon and look up ford 2.5 timing tool kit. I tried to clip a pic to show you.

[@chrisdavis9556]

It's a 3 piece. And at the bottom they have bought together as well about $100.00

[@Camaull]

would a bad crank pully make a 2012 ford explorer start a few seconds sluggish when using the turn key one flick start

[@chrisdavis9556]

Sounds like electrical issue . Is there a check engine light on ?

[@Camaull]

@@chrisdavis9556 no the car run fine but its the one click start is one of the issues

[@Camaull]

I have other issuse that will be sorted out 1 bad coil packs 2 a faulty throttle body 3 a faulty evap solenoid 4 faulty crank shafts pully all parts have been ordered

[@H3LLMAU5]

Today I removed the crank pulley without installing the service bolt or locking the cams in place, since then I haven’t touch the engine, you think I might have damaged the engine?

[@chrisdavis9556]

As long as you haven't started it you can still set ti timing

[@H3LLMAU5]

@@chrisdavis9556 no I haven’t done anything other than just removing the harmonic balancer

[@chrisdavis9556]

If you haven't gotten the timing kit Amazon has it cheaper.

[@chrisdavis9556]

$14.00

[@guille20089]

Hello what’s advise Can you give me if i pull out the harmonic balancer with out locking it put the new one and start the car and car won’t turn on now?

[@chrisdavis9556]

Yeah you have to have the tools to time it or no start . If you need to talk through it I'll send my number.

[@guille20089]

@@chrisdavis9556 thank you very much Chris I would appreciate that I got the tools now I just didn’t had them before. One more question can I reuse the bolt?

[@chrisdavis9556]

@@guille20089 yes

[@chrisdavis9556]

817-449-3332

[@guille20089]

@@chrisdavis9556 when is the best time to call you?

[@kirsten123ful]

Do you have to lock cams in place , or put number 1 cyl to tdc or is it just that crank tool only needed ?

[@chrisdavis9556]

Yes you must lock the cams on the back side.

[@arturomagana7587]

The pulley was removed without putting the bolt to CK your timing would that be an issue

[@chrisdavis9556]

No as long as you set the timing bolt in the side of the block you are ok

[@elijahsandlin9461]

The balancer does not control mechanical timing if you tighten it down without lining it up correctly it will only effect ignition timing.

[@chrisdavis9556]

there is no line up pin . the motor will spin and yes mechanical timing will be off.

[@markdavila5297]

What happens if you take off the pulley wrong without putting the special tool in the back and you already cranked it

[@chrisdavis9556]

Won't start

[@markdavila5297]

@@chrisdavis9556 I have to put the harmonic balancer in rite timing with the tool ?

[@chrisdavis9556]

Yes

[@markdavila5297]

@@chrisdavis9556 thanx

[@robertleavell712]

Can the. Harmonic balancer effect shifting in a transmission

[@chrisdavis9556]

If its off timing it can

[@robertleavell712]

There's whining when I start it up can't figure out if it's alternator ,a pulley or balancer any suggestion ,or tips. 2014 ford escape

[@chrisdavis9556]

Take the belt off start it see if it goes away. If it does . Spin all the pulleys see if any are rough. And check belt for cracks or oil soak.

[@thomassmith2739]

I have a 2011 ford fusion and my car cranks up but wont start i just recently changed the harmonic balencer what could it be

[@chrisdavis9556]

Sounds like it's not in time

[@MarySiebert-fk5ot]

I see that crank pulley broke the one on mine is making a loud rattle noise at idle goes away at acceleration so even if I'm just changing the crank pulley and not doing a timing job I still need this tool?

[@chrisdavis9556]

Yes

[@ljaymaster]

I have questions

[@chrisdavis9556]

what's up

[@ljaymaster]

@@chrisdavis9556 I'm driving at the moment but will explain the situation this evening

[@victorvargas1062]

What if you get out without knowing you need special tools

[@RichardRLeal]

Don't EVER use a pair of pliers to turn the crackshaft! That's cutting it up.

[@chrisdavis9556]

Only if you use heavy force.

[@kalebdarius3921]

Not that serious. Done it many times. It’s not a sealing surface so no worries

[@highlive2166]

THANK YOU!!!

[@tarritaylor1444]

Hey

[@chrisdavis9556]

@@tarritaylor1444 yes

[@mighandball13]

Tdc number 1 align balancer to the hole thats it

[@chrisdavis9556]

call me 817-449-3332