share your email, i send gerber and other details , you order it to your local pcb manufacturer

@@URJAautomation-tl2he send your email id

when left button press power bell rings, right switch press battery bell rings

@@zwtsch if you know and understand, you proceed with your own design, no problem

@@vmcdiytech3681 thank you, sir.

@@ChipLinck its just a 15cm length approximately, so no problem, with this i won't confirm that the filament is 100% dry, but you can reduce moisture and filament brakes while printing and inline filament dryer saves drying time

please share images to my email [email protected], i confirm you after...

its in starting of video it self

yes, some model of hdd is not supporting with usb, but works with direct desktop, you need to check with different converters to get a right thing or use external hard drive to usb box so you can use it as portable harddrive

@@vmcdiytech3681 turns out that my hub doesn't work at all it can't read data not in 2.5 and not in 3.5inch I want to fix it but I don't know how to connect the wires directly to the adapter jack

@@Rabah_issaad share images to my email and update me... [email protected] ,if i know i help you

@@vmcdiytech3681 thank you so much brother I will contact, I appreciate it 🙏 😊

share images of your devices to my email [email protected] and notify after you done ,i try my best to help you out

[email protected] mail me will check

ok ,i try my best

you can't add or remove ringtones from this type of calling bells because its a single time program chip and you can't program it by your own , if you required custom ringtone you need to use audio record ic and connect that to your receiver, you need to search how to connect before you start making

Happy to help

post me images, or link of Google drive, i can help you after seeing images, sorry for late response, i am in hospital 🏥

not understand, explain it clearly

Welcome 👍

the wiring diagram is not similar in all cables according to chip present in connector the wiring diagram will change

just add a spiral wire to anteena, of both receiver and transmitter

use an arduino and bell 🔔 ,program it as you required and you will get your required bell

because that pcb is very delicate and pcb traces are very thin ,if anything goes wrong the traces will cut out from pcb with wire foldings ,so i unsoldered all and re soldered same again and added 12v external power source

@@vmcdiytech3681 I think this step is unnecessary, and you can solder 12Vdc directly without de-solder anything.

@@Kuchuflaz yes , no problem,if you can...you can add 12v directly, without removing any thing, for video i need to show clear and clean so i did, all people are not expert's to understand at first time , some people are beginners , they don't understand if i go in express mode , so need to show full process 🙂😁, thanks for supporting me 👍🙌

you can't do it by diy, because you need that ic/processor present on converter to convert and read data from sata to usb and for that you need some software's tooo to read data from HDD and communicate with your PC , you can't find it in open source, so don't try to do that

@@vmcdiytech3681 so you cant take a port from a laptop and make it into a usb one

yes , some sata to usb has two usb-A male pins , that is because one is for transferring data and other is for power source, inside both are connected with each other

yes ,you can use it

YES , you can, but you need to contact tata service center and car decors to fix it perfectly NOTE :- THIS SENSORS WILL WORK perfectly when the speed is less than 15km otherwise it will confuse your driving while it auto trigger in some unwanted suitations

hello rizvan rizzy , we can't convert sata pin to usb , we can replace usb male pin with usb female port , we required that converted board (pcb ) to transfer data from usb to sata , so its not possible to change sata pin with usb port, if you required any more help contact in mail and share details like images and videos, but you need do at your own risk , we are not responsible for any damage, if need help contact to this mail [email protected] , have good day