Excellent Video. I can now go ahead and vacuum the pool.
@Lava_monk2 күн бұрын
Can you use the hose and a wet vac at the skimmer at same time?
@HallmarkPoolSupplies2 күн бұрын
@@Lava_monk Yes, good luck. Thanks for watching.
@PCDoctorUSA2 күн бұрын
One of my skimmers has 2 inlets, and it's my understanding that the inlet furthest from the pool is for vacuuming. How do I use a backplate in this situation? Do I have to plug the other inlet first?
@HallmarkPoolSupplies2 күн бұрын
@@PCDoctorUSA When vacuuming, if your skimmer has two inlets then you can plug. Most skimmers with two inlets will usually have a throttle plate on one of the inlets. Thanks for watching.
@Star-f2w2 күн бұрын
Can I leave my sand filter out for the winter and my pool pump with it, as it is very hard for me to put it all away for winter and do I cover it all up, what do I do and how. I have an above ground pool 15by30
@HallmarkPoolSupplies2 күн бұрын
@@Star-f2w Yes, as long as everything is drained and winterized properly. I have a video on how to winterize your above ground pool, hopefully this will help. Here is the link to this video. Thanks for watching. kzbin.info/www/bejne/kKu6epmOoKaUlcksi=jnGE8EvJsm0uendc
@TheRmilliard3 күн бұрын
Great looking pool/water and good tips. To be picky on step 3 i like to feed hose through skimmer opening not out up over the edge of pool as it diminishes the hose prime.
@HallmarkPoolSupplies3 күн бұрын
@@TheRmilliard You can do it either way, however, if you have a vacuum plate that has a straight hook up, then going over the top is easier and you won’t lose prime. If you have a vacuum plate with a 90 degree hook up then going through the skimmer would be easier. Most importantly, you don’t want to kink the vacuum hose. Thanks for watching.
@araceli89333 күн бұрын
Mark! Thank you very much for your channel! It's very helpful, I have a question my skimmer has two holes, I need to close one?
@HallmarkPoolSupplies3 күн бұрын
@@araceli8933 Skimmers have two openings, one is 1 1/2” and the other is 2”. 1 1/2” is standard on most skimmers and the 2” opening is usually plugged. If your skimmer has two holes that are both open then you have a skimmer that is tied in with the drain line or a vacuum line and it has a throttle plate. If so, you will close one when you vacuum the pool. If you are repairing a skimmer like this do not seal either opening. Thanks for watching.
@Mikero783 күн бұрын
I have a skimmer pipe and a vacuum pipe. Is this normal? I only have 2 pipes going in to the pump.
@HallmarkPoolSupplies3 күн бұрын
@@Mikero78 This is not normal but possible, do you have a drain in your pool?
@Mikero783 күн бұрын
@@HallmarkPoolSupplies Yes I do. 1 drain in the middle. Old pool, probably built in late 90s. I only have 3 positions on my Jandy valve. 1 opens the skimmer. 1 opens the vacuum and 1 closes water to the pump. Is it possible that the vacuum and drain are both on the same pipe?
@HallmarkPoolSupplies3 күн бұрын
@@Mikero78 Anything is possible, however, most skimmers, drain and vacuum lines are run separately. If your drain and vacuum are tied together then you can plug the vacuum line and check the drain, then you will know.
@Mikero783 күн бұрын
@@HallmarkPoolSupplies I don't believe they are. I only used the vacuum and I'm getting air in the pump, but if I remove the hose and leave the port open, the air bubbles go away. My vacuum hose is not punctured. Maybe the drain is with the skimmer?
@csaiz-y6v3 күн бұрын
Thanks for your prompt reply We'll just ordered a new seal plate
@HallmarkPoolSupplies3 күн бұрын
@@csaiz-y6v I have all the parts for this pump linked in the description of this video. If you have a super pump, here is the link to the seal plate. This plate will work for any super pump up to 1 1/2 horse power. Thanks for watching. www.hallmarkpoolsupplies.com/search.aspx?searchterm=Spx2600e
@jddeefo10224 күн бұрын
When I remove the 6 screws on my top piece and lift up, my diverter valve comes out still attached to the top piece. It seems that the top piece and the diverter valve are one piece, is this possible? At the end of the season my pool water was not staying clear and I suspected the sand and or the valve. I am now thinking the diverter valve is seized onto the top piece. Have you ever seen this?
@HallmarkPoolSupplies4 күн бұрын
@@jddeefo1022 If you have the same valve that is in the video and you remove the key assembly it is all one piece, from the handle to the diverter. The key assembly can be taken apart. If you need any parts, l have all the parts to include the key assembly or the whole valve linked in the description of this video. Thanks for watching.
@ulysseswarnero4 күн бұрын
thank this man a million! great video
@csaiz-y6v4 күн бұрын
Great tutorial, replaced my seals in 20 - 30 minutes. seems to still be leaking. rough Further inspection I noticed where the white seal is inserted was a bit rough where the seal sits. would this area cause to leak as well!!!
@HallmarkPoolSupplies4 күн бұрын
@@csaiz-y6v Yes, this is possible. Make sure that the seal is setting all the way down and that the surface is clean and smooth. If the seal plate is damaged you may have to replace. Thanks for watching.
@noahchingaipe5 күн бұрын
Thanks for helping sir!
@PeggyHorner-y9p5 күн бұрын
Great video
@audnbob15 күн бұрын
As first time pool owners, hubby and I love this video! He addressed every detail we’ll need to know! We’re both sitting here exclaiming, ‘oh cool, that’s easy enough!’ We’re both handy and he’s a mechanic by trade so yippee!!!! Thank you, and we have Hayward at that👍
@harleyinred5 күн бұрын
my new cartridge filter came with a broken gauge, can i still start up my pool, new gauge be here tomorrow
@HallmarkPoolSupplies5 күн бұрын
@@harleyinred Yes, thanks for watching.
@jaygossage23806 күн бұрын
I have a 1000 gallon pond with a water fall and a filter. The filter has some kind of pellets in the bottom and some spongy looking stuff on top. I back flush the filter straight to the lawn once a day for about a minute and the water is clear. But the pond has green moss/algae that grows in it. The water really looks bad. I use no chemicals. Don't have fish or plants yet. I was thinking about getting a DE Filter. What do you think?
@HallmarkPoolSupplies5 күн бұрын
@@jaygossage2380 The filter you have should be fine, as long as it is size properly with the pond. A pond will get algae regardless of filter you have. If you end up with plants and fish, having algae is normal. You can use pond dyes to help keep the algae under control, there are also certain fish that can help as well. Thanks for watching.
@Jordonarkyn6 күн бұрын
I’ve done all this. Still get no suction
@davidortega13246 күн бұрын
i like how you explain thank you
@TheWildbillfromnyc6 күн бұрын
But isn't the purpose of changing the gaskets to prevent leaks causing damage to the motor
@HallmarkPoolSupplies6 күн бұрын
@@TheWildbillfromnyc Yes, if needed. Thanks for watching.
@frederickeng55308 күн бұрын
Great useful video! Vinyl liner material should be available in repair kits.
@landofsaguaros83309 күн бұрын
That's bs. All that's going to do is make your drains suck in more water, then when the sock filter is clogged you get no skimming at all
@katrinweise85959 күн бұрын
Hi, thanks so much. Watching your video is so very helpful. One question... vacuum cleaning in the filter position would mean to shut down the floor drainage in order to have stronger suction, right? But what about the jets. They are on in filter mode and whirl up the clouds I actually want to vacuum. Would it be an idea to 1/2 close the wall valve, or even 3/4?
@HallmarkPoolSupplies8 күн бұрын
@@katrinweise8595 Yes, when vacuuming close the drain down for more suction but leave your return jets open. Do not close down the jets, however you can redirect them when vacuuming. Thanks for watching.
@seansalehi54819 күн бұрын
Thanks!
@HallmarkPoolSupplies9 күн бұрын
@@seansalehi5481 Thank you very much and thanks for watching.
@richardcassa10 күн бұрын
Great content, as always! Just a quick off-topic question: I have a SafePal wallet with USDT, and I have the seed phrase. (air carpet target dish off jeans toilet sweet piano spoil fruit essay). How can I transfer them to Binance?
@JJ-fg4wp10 күн бұрын
do you recommend adding chemicals a day prior to shutting the filter off and closing it for the winter? some articles say follow the kit instructions and others say shut off filter then add all closing chemicals and your done. Do I want the chemicals going into the sand filter since I will be emptying the filter? I am not using a kit and will buy individual bottles. Chemicals to close are 4 gallons of liquid shock, 32 oz of winter algaecide, and a bottle of pool magic, 2 gallons of antifreeze all for 29,000 - 32,000 gallons. Anything else like metal remover? powder shock? Any helpful advice? Thanks
@HallmarkPoolSupplies10 күн бұрын
@@JJ-fg4wp The proper way to close down the pool is make sure that the pool is clean and the water in the pool is balanced. Then with the filter system running you can add a winter kit or chemicals needed to winterize the pool. After adding the chemicals run the filter for at least 12 to 24 hours, this will be enough time to distribute the chemicals through out the pool. Thanks for watching.
@cantweallgetalong10 күн бұрын
What do you mean by sand in the pool? I have a 1989 that uses diatomacious earth in the filter and I just noticed it has showed up in small amounts in my jacuzzi and pool too. Is that indicating a problem occurring?
@HallmarkPoolSupplies10 күн бұрын
@@cantweallgetalong Sand in the pool is referring to someone who has a sand filter. If you have a DE filter and you are seeing DE in the pool then you may have too much DE in the filter or you may have a damaged grid inside the tank (a rip or tear). You also want to make sure that the manifold that holds the grids in place is not damaged and is secure and in place. Thanks for watching.
@cantweallgetalong10 күн бұрын
@@HallmarkPoolSupplies Thanks, I think my new pool guy messed up the filter manifold or grids,
@cantweallgetalong10 күн бұрын
I got an old Pentair 120v that got wet and rusted the contact parts for the bulb. I wonder what is the best way to clean up the minor rust, instead of buying a $400 replacement housing?
@HallmarkPoolSupplies10 күн бұрын
@@cantweallgetalong Try using white vinegar or baking soda, using either or both will clean rust off of stainless steel. Thanks for watching.
@cantweallgetalong10 күн бұрын
@@HallmarkPoolSupplies I forgot to mention that I'm reading a short with no bulb when checking the other end of the lamp cord at the junction box. This is what I gather is tripping my GFCI?. is that possiiby behind the accessible areas of the socket? So, if the contacts in the socket clean up, I should be able to read no short on the socket, or is likely still corroded and shorted inside the socket, but not accessible?
@HallmarkPoolSupplies9 күн бұрын
@@cantweallgetalong Give it a try, anything is possible.
@cantweallgetalong9 күн бұрын
@@HallmarkPoolSupplies Will do, but if it still reads a short, have you ever heard of a cheaper fix or replacement?
@HallmarkPoolSupplies9 күн бұрын
@@cantweallgetalong No, if it does not work then you will have to replace. Good luck.
@stanleyonyia180310 күн бұрын
I am not clear on the vacuum you just explained. My pool has a hose to hook up the hose, and the vacuum is the one that rolls (Hayward) pool cleaners. Then we have the skimmer with flat open face that water flows through the basket from the pool side. Often times, the Hayward pool cleaner will move for awhile and stopped and this leaves my pool full of dirty. Not much debris gets to the skimmer. How do I vacuum the pool in this arrangement? Thanks
@HallmarkPoolSupplies10 күн бұрын
@@stanleyonyia1803 Vacuuming a pool with a suction cleaner does not allow the skimmer to skim the pool at the same time the cleaner is working. If you use a robotic cleaner then you have use of the skimmer while the cleaner is working. If you manually vacuum a pool then you will vacuum from the skimmer or a vacuum line. I have a video that goes into more detail on how to vacuum a pool manually that should help. Here is the link to this video, thanks for watching. kzbin.info/www/bejne/rYbSnH-faLCEb7csi=PCg8COczpQry9L1I
@stanleyonyia180310 күн бұрын
@@HallmarkPoolSupplies Thanks a lot. I will try it and let you know the outcome.
@Entertainmentchann11 күн бұрын
Thank you for the simple and understanding explanation!!
@destindeplorable12 күн бұрын
My multiport didn’t lift when I unscrewed it & it feels stuck. Any suggestions?
@HallmarkPoolSupplies12 күн бұрын
@@destindeplorable If you have the valve in the video and you unscrew the screws on the key assembly the key assembly with handle will come off. If you are referring to the whole valve itself and you are trying to remove from the filter, sometimes the multiport gets stuck on the lateral assembly stand pipe which makes it hard to get off. Try turning and wiggling the valve, sometimes the lateral assembly will lift up when removing. If this happens you will have to remove the sand in the filter once you get it off. Lightly sand and lube the end of the assembly before you put it back together, this will make it easier to get off next time you remove. Thanks for watching.
@destindeplorable11 күн бұрын
@@HallmarkPoolSupplies thank you for the excellent information!!! I’m trying to get into the multivalve to see if the spring, gaskets etc are good. I removed the pin, handle and screws but the spring didn’t separate. It seems stuck. The whole port may need to be replaced I’m not sure. Didn’t know if I might be able to use channel locks or something to pry it apart or if that may cause damage. I’ve removed everything from the top to get it to separate on its own and it didn’t. I’m sure I’m losing water in the backwash & that’s what prompted me to take the port apart. On a side note- my hands felt like I put them in fiberglass afterwards. Maybe it’s the deterioration of the plastic on the multiport or not related- very odd.
@HallmarkPoolSupplies11 күн бұрын
@@destindeplorable It sounds like you may be better off replacing the key assembly. I have all the parts to include the whole valve linked in the description of this video. If you need anything email your contact info and l will be glad to help, my email is on my KZbin channel.
@harleyinred12 күн бұрын
How do i keep water from coming out with skimmer open?
@HallmarkPoolSupplies12 күн бұрын
@@harleyinred If you have a valve you can close the skimmer or you can plug the skimmer with a 1 1/2” threaded plug. If you are trying to repair the skimmer then you can lower the water level below the skimmer. Thanks for watching.
@harleyinred12 күн бұрын
@@HallmarkPoolSupplies i thought i had a clog, but my skimmer has a crack at the bottom 2inch outside, tomorrow may try to temp repair but think new skimmer right?
@harleyinred12 күн бұрын
@@HallmarkPoolSupplies filter building up pressure and water does come up good when turn it off
@HallmarkPoolSupplies12 күн бұрын
@@harleyinred Do you have an above ground pool or in ground?
@harleyinred12 күн бұрын
@@HallmarkPoolSupplies above 15' x 30' oval
@bobbyhunt300913 күн бұрын
Absolute Must See Video if you have a pool or are getting one. Homerun!!!!!!!
@quikcolin13 күн бұрын
Worked like a charm! Thanks!
@kaci778913 күн бұрын
I need to I know why debris, like dirt or algae from the bottom of the pool are returning to my pool as I'm skimming my pool?
@HallmarkPoolSupplies13 күн бұрын
@@kaci7789 For normal vacuuming and cleaning you want to be in the filter position. If a pool is extremely dirty or algae infested you want to vacuum in the waste position. When vacuuming in waste you are bypassing the filter so you will have to add water to the pool. If you vacuum this fine sediment (dead algae) in the filter position it will go through the filter back into the pool. Thanks for watching.
@kaci778913 күн бұрын
@@HallmarkPoolSupplies thank you. I actually have a push pull type not the multiport. Suggestions? I appreciate your help.
@HallmarkPoolSupplies13 күн бұрын
@@kaci7789 Backwash thoroughly and make sure your filter is clean and then you can add a little DE (1 to 2 cups) to the filter through your skimmer. This will help trap some of this fine sediment, when you are done vacuuming then you can backwash. You can also use filter savers, they go over your skimmer basket and also filter out fine sediment and debris.
@RaduBogdan2k15 күн бұрын
Any idea why most other youtubers recommend alcalinity first and ph second?
@HallmarkPoolSupplies14 күн бұрын
@@RaduBogdan2k Per manufacturer’s guidelines that is the recommended order, however, alkalinity is often added first if the pH and alkalinity are low. If this is the case, you would raise your alkalinity wait until the pH and the alkalinity stabilizes and tweak pH if needed. If the alkalinity is good and the pH is low, then of course you would raise the pH only using a soda ash. Thanks for watching.
@RaduBogdan2k14 күн бұрын
@@HallmarkPoolSupplies thanks, much appreciated!
@tdhoeffel15 күн бұрын
Awesome video. Is the 272526 the same as the 262506
@HallmarkPoolSupplies14 күн бұрын
@@tdhoeffel These two valves are the same. Thanks for watching.
@TheWildbillfromnyc15 күн бұрын
How often do u need to change
@HallmarkPoolSupplies15 күн бұрын
@@TheWildbillfromnyc You only need to change the seals when they fail and you have a leak. Thanks for watching.
@JoanMontes-r2b15 күн бұрын
Lee Donna Lopez Christopher Anderson John
@connieharder58215 күн бұрын
I found your videos helpful and I've only done a bucket test with no significant water loss so will look into the other ideas you presented. It sounds like it might be some sort of a pressure leak but I am wondering if you have ever heard of the problem I'm having. We have had our pool for 29 years (older than that but that's when we moved in) and have never had a leak issue until 3 years ago. The first year we experienced leaking, we did an underwater closing and that spring the pool was down around 2 feet upon opening in the spring. The next year we also did an underwater closing and the pool was down 4-5 feet with the entire shallow end and a foot or more down on the slope to the deep end was completely dry without water. Last year we did a regular closing where we lowered the water below the skimmers and it was also down but we had such a warm winter I was able to add water so not sure how much it would have leaked. This only happens in the winter when the pump is off and the pool is closed for the season and we hardly ever have to add water during the May - September swimming season. I've talked to several pool people and they have never heard of such a thing where it only happens in the winter. Any thoughts on what the issue could possibly be? Thanks! Connie
@HallmarkPoolSupplies15 күн бұрын
@@connieharder582 There are several things that it could be, however l need more information in order to help. If you would like to check out my Patreon page l will be glad to help. l can then work with you one on one and go into more detail about this issue. Thanks for watching.
@KevinLand-b7c15 күн бұрын
Hi Mark, great video. I simply want to replace my broken handle for my hayward multiflow valve (spx0715rx50) for a DE filter. I noticed in your process, when you removed the screws from the top of the key cover it appeared there were no nuts. I have nuts holding down the key cover, and it doesn't look like the bolts are long enough to remove them and try to install with the nuts when the spring is decompressed. Does this mean i can't change just the handle or could I get longer bolts to temporarily compress the cover? Open to suggestions. Also, I noticed that there are multiple handles for the valves. My has two arms, while the one you used is a single arm . Are these interchangeable?
@HallmarkPoolSupplies15 күн бұрын
@@KevinLand-b7c The multiport that you have is different than the one in the video. Your valve has bolts with nuts and the one in the video does not. However, the handle for your valve is discontinued but you can use the handle in the video. Hayward now has one handle that fits all their valves. The handle that you need is model SPX0710F, there is a link for this part in the description of this video. Thanks for watching.
@JG-re9it16 күн бұрын
I have a question about the shaft spacer and O rings #11. When I click on that item it only shows 1 o-ring. Does it come with 2 o-rings and 1 shaft spacer or only 1 o-ring? Need to know before I order. Thank you, Jasmine
@HallmarkPoolSupplies15 күн бұрын
@@JG-re9it The kit today comes with 2 o-rings and a shaft spacer. Thanks for watching.
@hw257716 күн бұрын
I've been maintaining my parents' pool for over 20 years, and this is the best explanation for how a pool system works. For me, this was also a good refresher; I learned/relearned some essentials, such as why the weir flaps and how setting up circulation in a circular pattern are important. I highly recommend your videos to other pool owners. It'll save owners a lot of hassle in maintaining their pools by just understanding these basics.
@Tonykayemusic16 күн бұрын
Can a 2 inch crack at the bottom of the skimmer cause a big loss (approx 1 inch) of water over 24hours in a 90,000 liter pool?
@HallmarkPoolSupplies16 күн бұрын
@@Tonykayemusic Yes, if your skimmer is cracked then you will have a leak but you can repair it. I have the schmear linked in the description of this video. Thanks for watching.
@Tonykayemusic16 күн бұрын
@@HallmarkPoolSupplies ill def get this product and hopfully that will put an end to the water loss. I plugged the skimmer and turned its valve off as well to test for leak on that line. I suspect that thst crack is the main problem. Thanks for your reply and for making great comprehensive videos about pools.
@mazcrafters17 күн бұрын
Do you have a replacement motor for the MaxFlo VS Variable Speed Pump, Model SP2303VSP? I couldn't find it on your spreadsheet.
@HallmarkPoolSupplies17 күн бұрын
@@mazcrafters That pump is obsolete and is no longer made. If you would like to email your contact info l can help. My email is on my KZbin channel. Thanks for watching.
@shannonfritsch664717 күн бұрын
Great video!! Thank you very much!!
@kennyg57218 күн бұрын
WOOOOW REALLY NICE EXPLANATION
@-redacted_by_youtube18 күн бұрын
I very rarely spend hours finding a leak. Can usually do it in about 15 minutes. Where the water stops is a pretty good indicator of where the leak is.
@shariqkhan541118 күн бұрын
Which sand i will use in 525 dia filter silica sand or sand media
@HallmarkPoolSupplies18 күн бұрын
@@shariqkhan5411 Use #20 silica filter sand. Thanks for watching.
@chucklakes234518 күн бұрын
What about a sump pump? I have a tube that goes down to the sump pump…6 inches wide with a cover on it on my pool deck. Should I pour antifreeze in it? Thank you!
@HallmarkPoolSupplies18 күн бұрын
@@chucklakes2345 If you are referring to a well point, you can leave the sump pump in the well. It just depends on where you live, what your water table is and what kind of winters you have. Do you have a high water table? Is this a vinyl liner pool? Where do you live?
@chucklakes234518 күн бұрын
@@HallmarkPoolSuppliesI live in Cincinnati. Not worried about a high water table. I’m just wondering if I need to be concerned about water getting in there and it freezes. Thank you by the way! I enjoy all your videos.