The casting for the lathe feet is in two parts? Thank
@mateuszturek5760Ай бұрын
the feet are whole
@yury740Ай бұрын
Hello, how long did it take to make the gate?
@mateuszturek5760Ай бұрын
hello, I built it in the afternoon after work, and I don't remember exactly, but maybe about 2 weeks
@yury740Ай бұрын
Hello, what is the power of the electric motor?
@mateuszturek5760Ай бұрын
Hi, watch the first part of the gate construction, it shows the engine with the nameplate :)
@yury740Ай бұрын
спасибо
@alfonzo102Ай бұрын
Dobra robota
@DenilsonFreitas-k5i2 ай бұрын
Muito bom, valeu pela dica
@thijs56662 ай бұрын
I fear the state of your skin after welding without gloves for a few years. Let alone the risk of loosing some fingers grinding without hood. Then again: i worship your skill.
@jayeshpanchal76332 ай бұрын
Good. Excellent work , accurate
@devilvortex12 ай бұрын
18 mm trapezoidal size?
@mateuszturek57602 ай бұрын
20mm
@sushiljalan2 ай бұрын
You are a Genius. 👌👍
@Harry_saimbhi2 ай бұрын
what is the ratio of this gearbox?
@mateuszturek57602 ай бұрын
I don't remember, I'll check and let you know, but around 1:30
@Frank-bh3cm3 ай бұрын
Please tell me you plan to render the walls and paint em? 😁
@mateuszturek57603 ай бұрын
Of course :)
@Frank-bh3cm3 ай бұрын
Talented beyond believe. If you really want to grow this channel, tell us what you're doing and why (in english = biggest audience).
@renildolima75253 ай бұрын
A continuação? Ela já está funcionando?
@mateuszturek57603 ай бұрын
Haverá uma sequência, tenho algum material para um filme, mas não tenho tempo de montá-lo nem de terminar a máquina totalmente. Mas a máquina funciona e já dobrou um pouco
@marutiagriculturemachine42103 ай бұрын
Can you share All Parts Details Drawing
@mateuszturek57603 ай бұрын
Unfortunately, I don't have them, the project was carried out "from my head"
@Mig-wg8iv4 ай бұрын
Jakie województwo?
@mateuszturek57603 ай бұрын
Śląskie 😉
@mahmudsaidych57314 ай бұрын
А почему нет испытаний аппарата? Почему не покрашен? Сколько всего у него рабочих функций? Ролик не доведëн до конца.
@mateuszturek57603 ай бұрын
Просто нет времени
@天蝎座-e5n4 ай бұрын
Какой ралмер рельсов на станке? 25 или 30?
@mateuszturek57603 ай бұрын
менее 20
@csabadoth48384 ай бұрын
Hey bud ... i love your home made boring bar ! Cheers mate !
@mateuszturek57603 ай бұрын
Thank you! Best regards!
@MaricelBarrun-lc2eh4 ай бұрын
K9j
@mrkrause35 ай бұрын
So nice!
@mrkrause35 ай бұрын
Awesome!
@_5_5555 ай бұрын
Слишком много заморочек, проще секционные поставить. Где защита от обрыва стропы?
@mateuszturek57605 ай бұрын
This has already been discussed, both belts will withstand 15,000 kg before breaking, and the gate weighs just over 300 kg. Moreover, it can work on one lane
@Alexey-qv2ie5 ай бұрын
Какой швеллер вы использовали для направляющих роликов? Какой их размер и толщина? Как поживают сами ролики выдерживают нагрузку?
@mateuszturek57605 ай бұрын
I made the bearing linings, i.e. the rollers, from polyamide, but their walls turned out to be too thin and over time they stretched, increased in diameter and fell off. so I made them again from steel and pressed them onto the bearings. I suggest making them from polyamide using a smaller bearing so that the roller walls are at least 8 mm thick.
@ugickwhellder55595 ай бұрын
👍
@loft3065 ай бұрын
There are very few Fab videos that I watch all the way through while this does not exactly apply to me. Thanks for the ideas. And yes I watched part 1.
@calf63496 ай бұрын
I am just a country boy from the plains of Colorado. Watching this video is like watching Vincent van Gogh paint "The Starry Night". His workmanship exceeds craftsmanship and tops at as an artisan ! The tools he used were quality. None of them were extravagant, just good ole every day workin' tools. Wow!
@mateuszturek57606 ай бұрын
I'm very pleased, Thank you!
@loft3065 ай бұрын
Yes!
@ll62616 ай бұрын
Bez Miękich szczęk nigdy Nie będzie dokładnie.
@name-p8u6 ай бұрын
лучше для такого метода использовать капролон например или фторопласт, они сжимается под нагрузкой сжатия и если кулачки не идеальные по геометрии и размеру в местах сжатия , то это скомпенсируется мягкостью этих материалах и при этом кулачки заблокируются всё равно , ибо если кулачки не идеальные по геометрии и размеру в местах сжатия , то вылет блока гарантирован и плюс будет перекос кулачков если они слабые в посадочных местах , тоесть этот метод это для новых идеальных патронов, с советским кривыми такой метод очень опасен как минимум
@ll62616 ай бұрын
Na starej tokarce nigdy Nie będzie top maszyna. Tylko dla domowego hobby
@DeonisDan6 ай бұрын
Отличная работа! 👏
@tomaszkluska64196 ай бұрын
Czy ty masz kopalnię diamentów za domem? :) To są kosmiczne nakłady. Zazdroszczę jak każdy tutaj :) Pozdrawiam!
@mateuszturek57606 ай бұрын
Cześć 🙂 cieszę się że Ci się podoba, owszem tanie nic nie jest, i trzeba było najpierw odłożyć trochę pieniążków, ale się udalo🙂 no i na szczęście nie było to aż tak kosmicznie drogie robiąc samemu 😉 Pozdrawiam serdecznie!👋
@tomaszkluska64196 ай бұрын
@@mateuszturek5760 Podoba się :) Pozdrawiam!
@CristianVillalonga-fw6ue6 ай бұрын
Hola como estas. Haber si te lo puedo resumir y que se entienda y que por sobre todo quede claro. "Un GENIO ", ( CREATIVIDAD, DEDICACIÓN, muy DETALLISTA). También observó que contas con una buena LOGÍSTICA 🤷. Excelente Trabajo 👏👏👏👌👍🫵, a pesar de no contar con los recursos necesarios me siento muy a gusto con lo que haces e "Identificado". Saludos cordiales desde mi País 🇦🇷 Argentina, 🫂🫵👌👍🙋♂️.
@dannybridges73787 ай бұрын
Make a foil ball dip in water and rub. It will take rust of your chrome
@muhammadharoon2367 ай бұрын
Good very good
@DrewRallye7 ай бұрын
Hi, this looks really good! What size tube did you use for the 3 main axle housings? It’s a really good design. Cheers.
@DrewRallye7 ай бұрын
Or were they machined from a billet? What’s the OD? Cheers!
@mateuszturek57607 ай бұрын
Hi, I don't remember exactly but around 90-100 mm wall at least 10mm
@lesnic_mgn7 ай бұрын
I hope that you blew the system before the first use. Because in the video, sand from the drilled block got into the pipe. And the job is great. The compressor always makes it very difficult to work with its noise.
@mateuszturek57607 ай бұрын
of course, I blew out the pipes before screwing the connectors into the connections in the workshop :)
@MiloBeni51697 ай бұрын
Excelente video!!!
@MiloBeni51697 ай бұрын
Excelente video!!
@user-197 ай бұрын
Golden hands
@kudubudu55517 ай бұрын
Jakie profile?
@mateuszturek57607 ай бұрын
Już nie pamiętam ale chyba 20
@irsevirando7 ай бұрын
💯!!!!!✅!
@yasamogu7 ай бұрын
Молодцы, но не понятно. Зачем эти затянутые переходы? Фиг разберешь. Словно накопил кучу видосиков и решил всё в кучу показать. Там что то пилит тут что то варит
@itzsamdiy7 ай бұрын
Grt work
@Manuel_Z_Kayaks8 ай бұрын
HE NEVER FINISHED IT!
@Manuel_Z_Kayaks8 ай бұрын
HE NEVER FINISHED THIS!... AFTER 2 PARTS All I need is a $10k metal lathe a $2k drill press, $10k band saw, $20k CNC, $2k+ of bits and dies about another $1k in hand tools, $£3500 Welder, $100 of scrap metal and I can build a $300 pipe bender. Honey.... I need the credit card!
@mateuszturek57608 ай бұрын
Money is not the reason for the still unfinished project, the most valuable thing is time, which is simply lacking, I run the channel not out of compulsion but for pleasure, and there is not always time for it... Nevertheless, I will finish it soon ;)
@KUATo3658 ай бұрын
С подтяжкой ворот тоже бьюсь давно!но делал на вело-цепях или тросах.но у меня отдельный эл.мотор дотягивает
@jan-magnenyborg8 ай бұрын
Amazing work
@paxmelkomi8 ай бұрын
А чего не показал как работает? Одна какая то показуха инструмента
@mateuszturek57608 ай бұрын
он еще не готов, о нем будет еще один фильм, который покажет, как это работает