Where can one buy these adapters?

How did you run the auxiliary tank

That space between the prop and the adapter needs to have washers to fill the gap, as weeds will fill the gap and hamper the water from the start of the prop

What Size is that trim bolt?

What length bolt and size did you have?

why not just get a long tail or a surface drive? This Twister tail hybrid seems like a marketing gimmick....

Fantastic video! Thank you.

Can u give me a link get an adapter

I have a question that I just can’t find an answer to. I taped my prop and ran it without a cavitation plate. I didn’t gain any speed instead I lost speed. I have an xl and I have a 6 1/2in prop on. I have a short transom and no jack plate. I’m assuming it’s the angle I have it on. So the question here is. It only moves my boat when prop fully submerged, so what am I doing wrong? At full throttle it picks up but as soon as it hit 5mph I feel the boat speed bog down and the prop does not ride the surface of the water. It doesn’t pull either way either. I’m ready to give up. On this twister. Also it’s a 420cc.

Where do i get this adapter?

What is the prop shaft diameter

I messaged you yesterday about problems with mine

I Hope this gets to you ive got a twister tail and can't get it right it either bogge down or doesn't go

Why not just go by "Feel"

Hi, for 212cc try to search at grab cad a propeller 199x199mm cleaver style. And for 420cc some people use 9inch prop and reaches 23 mph.

Where can I buy an adapter kit ? Please TIA

I have a amazon mud motor and I put a mud skipper prop on it but it must be submerged or it just cavitates, how do you do a surface drive like that? I am at a loss

Whats the length of the trim bolt you used to eplace the stock one with ?

We’re do I get the adapter at for this I need one bad I still have the 3 blade and it sucks

Does the mechanical pulse pump run straight to the carb or do you need a fuel pump and filter

For this video, did you remove/bypass the govenor ? And were you using the stock fly wheel or did you upgrade to a billet flywheel ?

Ate the twister tails pretty strong? Im looking at getting one with a 22hp motor but im worried about it holding up well?

Where did you get the muffler? I like how it goes to the rear and not the side like many others I’ve seen.

Hello, search in grabcad propeller 152x293mm, print try to improve more speed. Thanks to share the results.

What prop did you order? Like do you have the link to it? I order me the high speed 8.5x8” and the blade is too wide much longer than my shaft bolt so it wont even thread on. Should I get the 8x5?

Is that the dude from hot tub time machine?!

Amigo qual é melhor para o barco andar mais rápido,a rabeta reta ou essa curvada aí?

Have a twister xl on a 459 stage 1. Its running pretty good but it seems to need an excess of weight in the back to prevent the front from plowing. Running prop about half in water while on plane. Any ideas?

I see you are running a jack plate. What do you find to be an ideal transom height on the 5-7 hp twister kit?

Holding the prop in one hand and drilling with the other, watching the bit slide made me cringe. Get a vice

Nice❤

Hi

May I know how it is connected to the shaft type engine?

Great work! Thanks for sharing this video with us Rookies. I am in the process of going from a Johnson 15 hp to a Mudd Motor setup. Not sure what I NEED. My use will be just putting along fishing, fish line setting and getting to those honey holes off the creek and rivers. I am using to for myself and small grandkids once in awhile. Don't really need high speeds, just reliability. Your info was great and presented OUTSTANDING. You should consider writing a manuel or book on this topic! Appreciate Your contribution to this arena. Semper Fi

So the prop is right hand threads and the piece behind it is left hand?

Where can I buy the JACKPLATE on your j9n boat?

awesome video. exactly wat i needed.. iM GONNA MAKE A VIDEO OFTHE STOCK 3X BLAD VS 2 BLADE, AND SIZE COMPARSION ON ROCKY RIVERS SOON... ANYONE WITH A TWISTER (TWISTER CLONE) W/ 3BLADE STOCK PROP, READ THIS.. got a twister today first run, ALL STOCK, (ITS A TWISTER W/ GX200 CLONE OFF AMAZON) but its literally the exact smae as my buddys mud-skipper tiwster. only difference IS THE HANDLE DESIGN I COULD SEE.., an i got a g200 clone motor for free lol for the $$. i guesss we'll see how the clone twister lasts.. vs, mudskipper twister... ANYWAY, I PUT IT ON MY 30" WIDE 11FT Flat bottom on a fast moving river, And its a awesome setup. BUT i think the 3x blade OE prop is garbage for a twister. It either wont grab any or enuff water when set up near surface, and wont hardly push boat.. If i trim it down a bit below, it pushes like crazy, lots of thrust, but it does not have the speed. (still goes about 8 ish?mph) But i was a lill dissapointed. the 3x blade acts more like a blender, just chopping water.. hadta keep messing with trim.. (next mod is some sort of easy adjust trim) after i do 2blade prop... and lots of cavitation, vibrtation.. Also, i dont get any more speed bewtween 2/3 throttle or full throttle. I imagine this is why the 2blade props work best. its hard too dial in the 3 blade prop.. Its either, just mashin and splashing at surface, then just lower it and it grabs like a mofo.. But above 30-50% throttle, it doesnt seem too move much faster.. if down deep, like 4inch below the wake, it has lots of vibrations ,cavitations.. an feels like it slips (hitting different curents of water etc) -like a tire hitting ice spots on a roads. Especially in rivers.. I did get a 7" 2blae prop, Im goin too tap it, and install, I really hope, that it brings up the performance and smooths out everything.. I bet it will after watching so many videos of these longtails/twisters.. But yes the 3blade prop will get you moving on the water, and it would prob work great for a giant pontton boat, and in deeper water, with large heavy boats in ruff water, and since you only need about half the power, at 30% throttle, it stays steady and pushes hard.. Be great for puttin along.. savin fuel..or if you just wanta cruize and troll' fish.. But for speed, and smoothness, i can see a 2x blade swap is gotta be it.. The 3 blade mite work ok on a true LONG-long tail, were its far away from wake, of boat Tail, but its not great on a twister and small boat.

Great video. I really like the beginning where you show how the trim should be for optimal performance. I’ve been referencing your videos to try and dial mine in and it seems the prop has to be fully submerged atleast 3-4 inches to actually hook up and move the boat reasonably. Only seeing 13 mph max on a twister xl kit with an 8’ prop. Predator 420cc motor and 14’ v hull boat. Any suggestions?

Can you easily secure it with prop out of water say to float down stream?

Have you found that not having a grease zerk on the lower end does any damage?

Great Video! Do you happen to know the thread size/pitch for the twister to fit onto the adapter? I want to make sure mine fits.

What’s the advantage to having the twister set up vs a surface drive or long tail or even an outboard?

How long you been running one of these twister. Is it worth the money or is it junk.

What a nice truck you build,did you fix the truckbed yourself....looks good like a stepside chevy ;)

What size prop

What an awsome and informative video. Thanks

Can you explain how you put your motor when your’re pulling it behind your truck. Any tips? Because I recently got mine and I’m trying to find the best way to secure it during travel

You run 20 to 23 with set up

How much more speed did you gain with the Thai prop took mine out today and only got 7 mph with the stand prop idk if getting the different props is even worth it

That looks like Alaska to me. You still up here?