With that esr tool can you measure electrolit capacitor on board?

You use ready-made character generators. The smart way is to generate them in real time using one of the installed fonts on your computer! This way you will have more flexibility and a choice of different font designs.

Do you think this could be used in reverse? For example, the sensor monitors a water tank level, and when water drops below a predetermined level, the unit will turn off the pump.

can it be used for esp32 with hub12 Sir ? And then what about pin ?

can this also test voltage regulators?

Hi। Goidd tutorial followed all the steps, and connected the 1602 lcd display to Arduino nano, however to change the day date time etc whenever I uncomment those three lines and set the time , but compilation error occurs, RTC is not commented in the scope , if I comment them and upload the code it's all ok, but display shows oly 1 row if some rectangles that's it। Opened the serial monitor it prints time and the current date ।। Remedy ppls

Thank you so much bro. It was a very useful video . Please continue making such videos ❤

recently purchased to inline water flow sensors, both to ensure the pump doesn't keep running if there is no water. one is the liquid coming from my solar water - sometimes, even with 100% glycol it is frozen and cannot pump water through, the other is a water line that runs through the woodstove and heats the floor - again, in case of leak, or airlock so water is not moving would like to shut off pump. no information within sensor package to indicate how it is even used! very novice at arduino but i do have and have experimented a little.

Flight mode error kaise dur kare plz solution ❤

How to learn coding sir

Nice tutorial video. Thanks! 👍🏻

I likeedd a lottt ❤

Svp je voudrais le code , le lien que vous avez laissé en description n’ouvre pas

great video, how come my letters are black and all the rest is colored? its the negative from your example. tnx..

My drone was working earlier when I used to arm it. Now, it is showing error while arming that "Pitch RC2 is not neutral". In Mission planner setup, the default value right now is 1495, In full parameter list RC2_DZ is 20, RC2_MAX is 2006, RC2_MIN is 982 and RC2_TRIM is 1495. Also, I have recalibrated the RC and in Setup. What could be the reason behind the error?

hi sir this is a great video. im hoping if you could help me with my school project? i want to demonstarte how to pump water out from a car wash drainage. i will use the water to treat it and recycle for other use. thank you

i have an arduino uno,how do i connect the a9g board to the arduino ide through the arduino uno..thank you

I have the same issue but for both rc1 and rc2 and when I followed solutions there is no deviation in the trim value and the stick value !!

Can i use 1 watts speaker?? please reply😢

Sir,while am working on p10 board where connections and code are correct but p10 board is showing a straight line can you find a solution for this..?

Download Code is not working

how to change brightness?

useful knowledge.thanks

I did all the steps and then pressed AT, it shows the magic character, what's the error?

Can we use peizo sensors instead of digital motion sensor

How can I make digital clock with scrolling message using P10 with Arduino uno

Nice tutorial. Can you make a call from this device using the microphone that is attached in the board? Is it possible to attach a head phone to listen the person from other side? Thanks

Pls kindly help with schematic and code for petrol price display board using P10

Hello everyone, for anyone reading, I want to ask, I have a problem when installing cayene on raspbery pi it always loads in the software component section on the cayenne website. Is there any solution for my problem?

Good job, Please, there is any solution to connect dmd p10 and mini sd card module to arduino nano ? Because they use somme same pins, thanks

Hello, I wanted to ask you if you can make an access counter with the internal memory of the rfid card. Let's say I use two readers. With a reader you can record the number of accesses on the card and with the other reader authorize the access and gradually discount the number of accesses from the card. It would be two Arduinos with two different readers. Is it possible to do that?

jazakALLAH azhar bhai...!

Do we need smart bulbs for this ? Pr normal bulbs and device is fine...

Problem statement:- when an object enters into the geo fence, the buzzer and led will turn ON until object is in geo fence. Please can u help with this Code and hardware idea

Does https runs for~ 7 minutes and stops working in code?

the nodemcu is not connecting to the ssid provided in the code after dumping the code please help.

Nice video. Please make video on running boarder around scrolling text using P10 dmd board and arduino. Thanks in advance

Sir please send me the code.

Please give ckt diagram

The video cuts out at about 11:40. Helpful video though, so thanks!

this video was great and really helpful but it would be more helpful if you can share block diagram also

Is it okay if i Use arduino uno only?

Can I use RFID sensor without Arduino

After install Ds3231 library it is not done. various error message has been coming. set dow in rtc. rtc begin me error message ati hai. Sir please answer me.

Sir when try to compile the sketch this faulty message is showing. "No matching function for call DS3231::DS3231(contunit8_t8, const unit8_t8". What can be done? Sir please answer me. I can't done that. Please help me in this regard.

Howmany panels can we cascade.. without affecting brightness for static display

how to make it using esp32

hello can I connect it to 230V

hi Azhar, which cmd can i use for auto answer ?

This module only support 2G and 2G mobile networks are no more now. It is now kind a useless. So you will not be able to use this module post a location to a internet. SMS and GPS will still work where there is coverage.