Just had both struts on my 2019 pilot EXL replaced. Now the upper strut mounts are making a rattling noise and a loud thud/Boink on the passenger side when turning left at slow speeds. What would cause this on new struts/strut mounts?
@kitlacaden3 күн бұрын
Did you check the mount? Possible mounting is damage also.
@dannynguyen6555Ай бұрын
Hi, Thank you for your video. Sorry to bother you, I need your advice. I got a Honda CRV 2021 , my car get the warning light "Auto Engine Idle Stop System Problem" I changed a new battery sensor but it didn't fix the problem. I scanned the car and it showed the code "P16E3 PGM-FI Battery Sensor LIN communication Error". Some mechanics told me its POWER SUPPLY STABILIZER CONTROL MODULE need to be changed and some mechanics told me my car need to "update the gauge controls module's software". Please advise me what should I do to to eliminate the warning light "Auto Engine Idle Stop System Problem" and Code P163E3 I can pay for time to advise me to fix this problem. Very appreciated for your help. Thanks again!
@jontai57292 ай бұрын
Good video, can you make more for the Honda Odyssey RC1 please? Thanks
@kitlacaden2 ай бұрын
Im not working in honda anymore sir.. im currently working in different brand. ;)
@jontai57292 ай бұрын
@@kitlacaden Not a problem. Your videos are so helpful. Good luck and all the best mate!
@gnoyl2 ай бұрын
LOL he removed the steering pump XD might as well take out the whole engine next time wtf :DDD
@sinofpride85162 ай бұрын
Lowkey this video is pointless. All your showing is screwing in the oil pan no steps on how to get to it or what you need to remove to get to it
@CarlosGarcia-fc2ux3 ай бұрын
Elque Sabe sedivierte dijo tilin
@crstlxlxdn3 ай бұрын
Fightingggg !!! ♥️
@erynemken53174 ай бұрын
He forgot to put the Spring back on….OPPs
@blakefl86234 ай бұрын
Would this be the same procedure for a 2019 Odyssey? Seems like it would be almost exact.
@kitlacaden3 ай бұрын
Yes but different style..
@blakefl86234 ай бұрын
Did you replace the Mount Base and Bearing?
@kitlacaden4 ай бұрын
Only the mount base.. you can re use the bearing if parts is not available
@blakefl86234 ай бұрын
@@kitlacaden Great, I purchased the base as well. My struts only lasted 55k miles and Im not even in a rust area.
@danno58054 ай бұрын
Thats the pump and not the filter... right? 🤔 🤷🏿♂️
@kitlacaden4 ай бұрын
Filter and pump..
@kitlacaden4 ай бұрын
That assy contain pump, sending unit, and filter..
@danno58054 ай бұрын
@@kitlacaden ok, I thought the filter was on the firewall under the brake buster.
@kitlacaden4 ай бұрын
@@danno5805 the black one, thats a evap canister..
@kolemarieee17144 ай бұрын
Is it the same process for all 4 windows?
@kitlacaden4 ай бұрын
Yes ;)
@yUNGFRo234 ай бұрын
Part number for the spark plug O rings ?
@FranciscoPerez-il3rv5 ай бұрын
Awesome job, thanks for sharing
@jimmymasagca84605 ай бұрын
Ano po ang torque specs ng bolt sa vtec solenoid at rocker arm holder?
@Lone-Wolf875 ай бұрын
How much $$$ does it cost to replace all of that?
@charlieyoung47605 ай бұрын
Is it accord?..
@kitlacaden5 ай бұрын
Nope.. odyssey j. But same engine with accord 2015.
@JP-ku3he5 ай бұрын
Great video love that he just got straight to the point and showed the entire process
@hondaguylee88376 ай бұрын
You can tell they don’t work on rusty cars. And who the heck wears white as a mechanic?
@kitlacaden6 ай бұрын
That's the standard from japan, ;) try to search honda mechanic in japan..
@kitlacaden6 ай бұрын
Also soichiro honda wears white, the one who established "honda". ;)
@hondaguylee88376 ай бұрын
@@kitlacaden Must only work on new cars Here state side, cars get way more dirty. No way you can wear white and be a mechanic
@kitlacaden6 ай бұрын
Im working in honda in middle east for 10 years and my uniform are all white. Even honda Philippines dealers wearing same uniform.. we can do anything, because that's the standard..
@hondaguylee88376 ай бұрын
@@kitlacaden Been a Honda tech for 20 yrs. No way white will work here.
@DOS_SERVICE6 ай бұрын
Is adaptation necessary after replacing the BCM?
@kitlacaden6 ай бұрын
No sir.. its a mandatory in certain vin..
@I_eat-water.9006 ай бұрын
Great job
@PurpHaze8306 ай бұрын
You don’t have to remove power steering pump, you only have to remove blower hoses, the bracket bolts for those said hoses, and the bracket bolt for the power steering high pressure line, you flip the bracket upwards after removing the bolt and push it out of the way. I did it last night and it took me 1 and a half hours maybe just a little more, removing the pump adds on and extra 30 minutes because then you gotta replace the seals for the pump beings you removed the pressure off of the old seal and now that seal probably won’t seal the same again.
@saraaru51377 ай бұрын
Great job. Thanks for sharing.
@mdaaravakram84697 ай бұрын
Where r u now???
@kitlacaden7 ай бұрын
Im here in Australia right now.. ;)
@mdaaravakram84697 ай бұрын
@@kitlacaden plz give me advise how to I go ..
@mdaaravakram84697 ай бұрын
Abdullah mahfooz 😂😂😂😂
@mdaaravakram84697 ай бұрын
Right now I'm working that lift abdullah hashim only two Philippines left jamie n rey
@Blaxicanking097 ай бұрын
Great video🎉
@louiehora46087 ай бұрын
hello, i have the same model year honda. thank you for showing us this helps us alot. Im just wondering what kind problems did this is showing. Is vibrations and shuddering a common thing on struts because im getting a lot of vibration and shuddering on my pilot specially in the front driver side. Thank you so much.
@SUPERCHARGE77 ай бұрын
Why are you updating the software ? I have same model car 2018 odyssey
@jeanniebright99387 ай бұрын
Great video, This is the way I did it. Much easier than removing the seats, plastic flooring and pulling the carpet back to get access to the pump. I had my fuel tank down in 30 minutes and pump off.
@vendrabagus30747 ай бұрын
how to remove on rb1
@bcw6867 ай бұрын
Where was the a/c compressor?
@kitlacaden7 ай бұрын
I just leave inside the car.. to avoid discharging the refrigerant
@hugolrivera26748 ай бұрын
El mejor video creo que yo puedo gracias brother
@vioreza32338 ай бұрын
Niceee.. own a j series and very good enginee.. subs+1 for your channel!
@mightyducks58678 ай бұрын
Could you help? When reinstalling the strut, i noticed an arrow on the top bearing. If you didnt mark when you rook it off, which way?
@kitlacaden8 ай бұрын
That mounting is only fitted in their own location.. and the arrow will point to engine bay or at the back if im not mistaken..
@mightyducks58678 ай бұрын
@kitlacaden so, the mounting plate can only be installed one way, the bolts will go through the bottom only one way?
@kitlacaden8 ай бұрын
Yes..
@warbird878 ай бұрын
Great video my friend. You can tell that you have great pride in your work. I will be doing this job on my moms 2019 pilot this weekend, and definitely using your video for reference.
@mightyducks58678 ай бұрын
Make sure you.mark the top mounting plate for reinstall. When I did mine w a s a big headache .
@prestonmiller65289 ай бұрын
Why did you remove the full rocker assembly to replace the rocker control valve? Do what the technical bulletin says from Honda and save significant time.
@prestonmiller65289 ай бұрын
Poor quality work. Do not remove the engine and transaxle assembly from the top. Lower from the bottom.
@AbeMurillo7777 ай бұрын
Poor quality??? This man did great ! Maybe you should put your own video together instead of being negative.
@nevessl9989 ай бұрын
And.. how much was it?
@Nicedesk9 ай бұрын
This is some major preventative maintenance! All seals replaced!
@Nicedesk9 ай бұрын
Now I see how you keep your clothes white haha!
@bigpapi889 ай бұрын
labor hours?
@kitlacaden9 ай бұрын
6-8 hours
@daveclark83375 ай бұрын
At around 100Kish miles on a J35, most all of that stuff is going to start leaking or need to be serviced. So if you're going pay a shop anyway, it makes sense to pull the engine and do it all once on the stand, versus fighting in a cramped engine bay for hours: Water pump, timing belt, valve cover gaskets, valve adjustment, rear main seal, solenoid gaskets, maybe even motor mounts too.
@granddelimasentulofficial69589 ай бұрын
hey dude..what kind of silencer that you use?
@kitlacaden9 ай бұрын
Stock krytac kriss vector silencer..
@kitlacaden9 ай бұрын
I just modified the mid part and wrapping with a cloth tape
@brandonhaney70029 ай бұрын
Hands-down, the most annoying background music I’ve heard on any video all year. The content of the video is good, but I’m not sure it’s enough to offset it…Freaking annoying. At least loop the shit, right
@WiliamRamirez-v7u9 ай бұрын
Mi hermano usted es un gran mecánico
@abel374510 ай бұрын
HOLA , LE HICE EL CAMBIO DE LA JUNTA AL MOTOR Y CUANDO PRENDO EL CARRO SIENTO UN SONIDO DENTRO DEL MOTOR , COMO ALGO ROSANDO, QUE PODRA SER POR FAVOR, A LA HORA DE QUITAR O COLOCAR LA TAPA SE PUDO HABER MOVIDO ALGO ??
@SUPERCHARGE710 ай бұрын
Why you replaced the L/R D shaft seals ? If they are not leaking ?
@kitlacaden10 ай бұрын
As per warranty instructions.. ;)
@shouryapendyala342310 ай бұрын
the lift point for the engine on the front right, am I seeing this right? hang it off the throttle body?
@DilipBalsaraf10 ай бұрын
Wow! Lots of hard work man! Tremendous knowledge you have!
@SteveLong-l4f10 ай бұрын
Got anything on replacing eco switch on 2016 Pilot. Mainly access to it.