Mi fuente ATX entrega 12v y 24 ampers lo dice en la etiqueta
@peterk883228 күн бұрын
Yeah glue the potentiometer screws and sockets and fuses because screws just mysteriously wind themselves. You didn't glue the case screws, it will fall to bits, in fact just dip the whole box into glue just to be sure.
@jimmatrix724428 күн бұрын
Led light glare is visible, Overall excellent DIY.
@ChamindaRajapaksha-nh6jtАй бұрын
පැහැදිලි නෑ....
@neo37682 ай бұрын
You should sell this. It looks more affordable than a market micro scope,of the same quality
@keith_ferdinanduz2 ай бұрын
I have the same boost converter. I boosted 12V to 30V, I only could get 3A max and the input current was above 10A. I tried 3.5A but input current raised upto 15A, there's a 15A fuse at the input side. In this video he boosted 12V upto 54.5V. I'm pretty sure maximum you can get is around half an amp at 54.5V.
@imtan2x2 ай бұрын
That image quality. 💯👍👍👍
@TaruTruna2 ай бұрын
Well done!
@zajkor4 ай бұрын
I would be interested in 3D printing the casing but could you please export your Solidworks files in .step format so everyone can use them. Solidworks files are not compatible with any other software.
@MKTECHCASIO4 ай бұрын
Hi
@yaminis55374 ай бұрын
The code you have given is wrong..i tried doing this experiment and nothing is showing in the lcd display..why can't you give correct details of the code?
@xJackHunter4 ай бұрын
great video please just dont use such bad music
@jamesrodemeyer75445 ай бұрын
Also include automatic led, zener tester.
@jamesrodemeyer75445 ай бұрын
Use loctite for nuts.
@jamesrodemeyer75445 ай бұрын
Remove covers from power supply for better cooling, also remove excess wires from power supply board directly. Very nice job, the case looks good.
@walterwhite19695 ай бұрын
How can you make this miracle happens? Using a 225W power source and a boost converter (91% to 96% efficiency) you'll get up to 250W output? 216W at its best. Do the math.
@Mr_Negative4205 ай бұрын
wth was crawling on the pcb xD
@m4rt1005 ай бұрын
how many lens that you use. thank you
@m.j.srinath86534 ай бұрын
Just one
@Klasykarozgrywek5 ай бұрын
Why you used 100 Ohm resistor on pin V0, thank you for respond ?
@fmphotooffice55136 ай бұрын
Bravo! Well done!
@user-gw1pj7fh7q6 ай бұрын
To correctly measure the battery capacity, you need the discharge current to be stable, and as the battery discharges, the current starts to drop, you need to create a current stabilization program in the sketch and control it using a PWM transistor to discharge through a resistor
@narindersingh24746 ай бұрын
Es splay se 12v 100 amh ki batery charj krskte h
@q12x6 ай бұрын
excelent !
@user-eb4cb6ot1j6 ай бұрын
ese es un tutorial de calidad
@samudracell.6 ай бұрын
👌👌👌👌👌
@o0onho0o123457 ай бұрын
Thank you so much !
@umarismail51787 ай бұрын
keren om
@rayespinosa50157 ай бұрын
Can you give the size of lens sir?
@Josueee77 ай бұрын
En el codigo falta agregar digitalWrite(pinMosfet, LOW); por que si no sigue descargando la bateria y eso es muy peligroso
@makaderjibon76518 ай бұрын
Super
@minravex99198 ай бұрын
this is exactly what I need for school project....please I can buy you a coffee....I want to request a comprehensive lesson video pls
@minravex99198 ай бұрын
this is exactly what I need for school project....please I can buy you a coffee....I want to request a comprehensive lesson video pls....I don't have arduino experience...but I'm a fast learner
@DumitruDanila-uw4xz8 ай бұрын
❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
@The-KP8 ай бұрын
Those are solder mites.. responsible for producing the 'tin whiskers' you see protruding from that IC's right side
@Guishan_Lingyou8 ай бұрын
good job.
@AL-kn4yx8 ай бұрын
What is the amp rating for the fuses?
@JesTheii9 ай бұрын
so any future plan on autofocus?
@tranang37889 ай бұрын
I am new to circuit making, can you explain to me the operating principle of the mosfet in the circuit?
@kadalkadalan361810 ай бұрын
Finaly,15-20cm distance is good..appreciate your hard work,thnks.
@hi-techsoundsolutionsahmed286810 ай бұрын
Good
@JoeyMoreland10 ай бұрын
Well done.
@fellpower10 ай бұрын
Next time try 50V and 5A - and u will see, after a short time, it will blow up ^^
@rondo12336 ай бұрын
Elaborate
@keith_ferdinanduz2 ай бұрын
@@rondo1233actually it won't blow up because ATX PSU has protection circuit built in, if the load is too high the PSU will shut down. But he used only one 12V wire, that single wire isn't capable of delivering 12A. This ATX PSU rated it's +12V @ 12A, that's 144W. The boost converter always consume more power than it's output power. He boosted 12V upto 54.5V. He claims this PSU delivers 5A @ 50V that's 250W. You see it's not possible to get 250W out of 144W, right?... And the boost converter has a 15A fuse at it's input, boosting voltage upto 54.5V from 12V will consume more than 15A of current when a load is connected. I'm pretty sure you can only get few m.amps of current at 50V.
@mihainicolae76410 ай бұрын
HELLO YOU CAN MODIFY FOR TWO 3.7V CELLS IN SERIES THANK YOU
@ugurylmaz766610 ай бұрын
👏👏👏
@mermitkadi879511 ай бұрын
سلام فكرة رائعة جدا واصل
@adnabandasha320111 ай бұрын
Good job
@hendrih270711 ай бұрын
Nice Project, what software name that use for connecting camera and PC?
@alexjav111 ай бұрын
lol... any soft
@user-qb7mc5do6d Жыл бұрын
File is not open
@user-ef4zi9mb9k Жыл бұрын
А зачем было бустер ставить отдельный? Wz разве не sepic преобразовптель?
@GCAGATGAGTTAGCAAGAАй бұрын
WZ5005 только понижающий, можно было установить другой преобразователь: WZ3605 он понижающе-повышающий - вроде так.