Does this work on the 2007 ?

you deadass didnt tell us no specs or tools omfg

What if the bottom bolt gets stripped and you've tried everything to get it off?

Hey bro I know its late, but this is a super dragger 1 right not a super drager 2? I'm asking because I found a super dragger (1) for a good price but i dont know if its for a supra or is300 i'm a little confused

i got 5 codes on my 04 is300 po441 po442 po446 po441 po446 i replaced evap canister check engine light just came back up what should i do

Where did you get all the leds

I’m gonna try 👩🏽‍🔧 Thanks Vincent.

Does the dimmer works with LEDs?

You forgot to mention about 2 other screws. 1 under the reflector and 1 at the bottom under a pop out cover. If you don't remove them you can crack the wood like plastic trim.

You need to remove bottom 2 more screws,one at the red right when you open it you can see it and the other one is at the round shaped rubber just open it you can see the screws.Thanks for the video👍

Tools needed???

This was very helpful and all my questions were answered.

You missed two (2) fasteners the one behind the marker reflector and the bottom one with the pop cover. Nice try thoug hope your viewers didn’t destroy there own panel…rob442

I have this car I need answers

I have new one in box from 6 years,how can i know working fine or not before installing? Thx

Just finished a 2002 GS300 rear brake job. The car came in with the shims incorrectly installed. When I installed the new ones, something didn't feel right because there was no downward tension on the brake pads. Some of the other videos also show them incorrectly installed! After you pointed it out, I had the correct installation. Thanks!

❤❤❤❤

I was able to replace one of the hoses in the rear without raising the charcoal cannister. Are there two hoses (that has vinyl covers) near the cannister? If so, they are the same part number in your video? And the aisin vsv, is that located driver or passenger side of the cannister. In the video, the part pops up randomly. Not sure where it is. Can it be swapped out without removing the cannister? I noticed there is a screw that holds it down. Thanks brother. Youve been extremely helpful.

Can you clarify what I am supposed to look at in the one screenshot? Air filter box vacuum switch hose? #17342D and #1700H. Are those part numbers? For what?

Did the transmission start to slip after the fluid change? And do you change the filter as well?

This thing gets stuck all the time and I have to put it back in place so it doesn’t keep running water

vincent, thank you for the great video!

Awesome.

Best head light video on KZbin👻

they followed proper repair procedures. That’s not a plug, that’s a solid rubber stem filler and they more than likely layed a patch on the inside with a repair sealer. This is the standard set out by all the tire manufacturers. I see nothing wrong

Do i need a gasket or high heat sealant😮

Thank You So MUCH, Mr Vinsanity Motors, simple video but Very Details information with Pictures of the parts and Parts number. I am now your subscriber.

so basically change the entire EVAP system ? lol

Do you still have this faucet?

One of the worst quality levels in a video I’ve seen in my fucking life

Thanks 😊

What kinda foam gun is that

Salamat for the video. 👍🙏

how many km can you drive after the oil change?

Any idea on how to set the height where your hands are when it turns the water on?

easy steps my bro! thank you!!!

Awesome, thanks

great video! short sweet and to the point. exactly what i needed

I have a bad voltage regulator in my alternator that when I accelerate hard, it sends 15v or more to my battery which boils the acid in the battery....can I run this voltage regulator BEFORE THE BATTERY WITH THE POSITIVE CABLE FROM THE BATTERY, then run a positive cable to the battery from the D1 spec voltage controller to make sure the battery doesn't go passed the 14.6 volts max limit???

the end made me smile:)

Is the gasket better than the RTV that was on there before? How is holding up?

Thank you my friend your video saved me $283. They were asking $300 for the replacement. I bought the mirror for $17 of Amazon and watched ur video how to replace it. Appreciated.

What size are the first two nuts? That would be helpful in future videos, like a tool list.

didn't show how to replace lower 6 spark plugs

Gy

Finally# 3rd video is the charm. All the other vids do not show how to remove the metal key from the plastic encapsulation. Your video is the most complete demonstration for this job.

How can you check the actual pressure inside the cluster or screen of atlas?

Ur boy is cute! And ur Prius looks nice!! I hate to say but ur not lifting car properly. U must lift the center up front & center in the back. THEN jack stands go at the pinch welds u DID use. Where u lift is not thick & may cave or bend. Also I keep 38 lbs in back/40 lbs in front. U can keep40 lbs all around. As long as u stay at least 5 lbs UNDER max labeled on ur sidewall of ur tires, it's safe. I get better mpg's & more even tire wear. May ride a little rougher but my alignment guy recommends & my 97 camry wore long/evenly.😉 U got a 👍 & I sub'd. Hope to see more prius videos. I have a 2019 Prius Limited.😁

Weredo the terminal ring at.

About to do the valve cover and gasket, oil pan gasket spark plugs and cv axles on my moms 08 Sentra this coming weekend, just waiting on all the parts to arrive. Figured I’d see how easy it was to do this and the injectors also; guess I need to grab a new gasket throttle body cleaner and add this to the list this weekend. Great video and nice beats to it!