I think I just did mine

stumbled upon the legend himself.

great vid!! i like long vids

The aluminum parts are Dorman 926-111 Door Latch Cable Repair Kit sold at Auto Zone. $13.99. Comes with four in a bag but one is specially built for a certain spot on the latch. You will see it looks squarish verse round. Make sure when taking apart you see which one it replaces on the latch. I do like the tie wire idea but if the plastic ends are they need replaced.

Amazin'

Is there a designated subwoofer or tweeter in this truck?

Awesome video. To the point. Thanks!

Do you have a link for those speaker adapters. I need to do the same to my 99 f150. Thanks for the video!

Thanks for the video bill. It's unfortunate how the tools on newer bikes are inadequate now. My Z400 didn't have the 24mm in the toolkit and when I watched a video of the ZX-4RR's toolkit it was *literally just a single Allen Wrench and a Philips Screw Driver*. It's just so sad

Good to hear i got a 98 wv 5.4 doing the exact same thing lol so time for a vaccum tune up as well

Спасибо😁🤝

I can't locate the first two videos to the 2000 f150 idle

My concerns with my first oil change were on how to level the bike properly while checking the level and that my bike seemed to take more significantly more oil than in the manual(about the same yours did). Another concern was the lowering link the previous owner installed but it seems you have one too. From one airforce to another, thank you Bill.

That's not a sheet metal screw. That's the correct screw. The 4.6's with the aluminum intake plenum uses actual bolts that thread into the aluminum. The OEM ford intakes have brass inserts that are pressed into the intake manifold with actual bolts just like the 4.6's. That is an aftermarket intake on your truck Edit: I know this is an old video

Just replace it with a new barrel. Problem solved..

great video thank you. will be attempting this on my 650

Won't idle dies every time u let up on gas

1994 f150 idle prodlems

You're living the life man!

Just did the back one's found out passenger side was out now it's time to do thank you so much for doing this one of the best showing it

Good shit, homie. Did it in 30 mins and saved $200 from lowest labor I found and $40 from mark up part prices.

Where did you buy all the vaccuum lines from?

What is that rattling I have the same thing

I have straight bars I want bars like yours what is name and size

Remove the sight by drifting out the 2 wedges at the base and install a peep site. Problem solved. That gap will disappear and there is still more than enough material holding it together. Don’t install the type of scope mount that applies pressure the same way as the sight.

I would not do anything with it because I’m 12 and my grandma and grandpa just got me one from Baker air guns and they will also fix air rifles and do a real good job

DON'T HEAT IT UP! To fix that requires a total disassembly, or you will ruin the seals inside the gun. I'd leave it as-is and mount a scope to the receiver/breach part of the gun. But either way definitely remove the ear sight! I'd go with a peep if I were you!

Go PACKERS!

Thank you it's people like you they want to help other people who keeps my stuff going

Super helpful, thank you!

This was an amazing video

I start my truck turns over then stall in park and drive can any body help thanks 🙏

I see a blue and a brown wire. Which one is what? My led flasher relay has a red for IN and a black for OUT

I have a '99 and had to do both back doors. Yes, it's a pain. No, it's not really easy ( not hard, just a aggravation). Yes, if I did it you can too. Saving near $400.00 by doing it myself... now that's real good.( and worth every minute it took! )

Amazing Bill. I'm going adjust the chain myself from now. It costs me $30 each time tighten :( I don't have the keys/tools inside, same problem with others (Ninja 300)

5 and 6 are easy but, 7 and 8 are tough! Unless you take crap apart…lol

My front blinkers stay on and dont flash and rear dont turn on

Just add rotating the tire as you do so, to see if sproket mount bushings worn, if rotating tire while measuring out of range then tight while roting fully ....🏁🍾🔧🏍️...😎

where did you get the headlight at? need one for my bobber s40

Mine randomly started idling too high. Used to idle at 6k, now she idles at 9-9.5k RPM. Any ideas?

Thanks mate. You are teaching me a lot as you go, I appreciate it. Thank you

Damn I can’t do this man I’m too dumb de this lol

Did you make the risers or where did you get them ??

With thesee Ford's you have to replace most sensors on the intake throtlebody, including the egr valve, personally ive replaced all sensors,fuel injectors, fuel pressure regulator and maf sensor along with all vacuum lines, problem solved.

You should of done it from over the chain. Not from underneath the chain 😆. Good video. Now I know Wihch way up up. Thanx.

I have the 4.6, the issue I have is a very low idle once the engine is warm. Feels like it is about to stall, but then revs up again. Already replaced IAC, and TPS sensor. Also cleaned out the throttle body. Any ideas?

Thank you, amazing explanation

thank you very much for the helpful advice.. you are the man. very grateful for your video. thanks for taking time and posting it.

Had both doors fixed within 30 minutes. Thanks for the video, it helped so much

I used plastic zip ties. But mine is a 97 and a bit different. I didnt have to mess with the bottom cable.