Does the motor you used make you feel realistic ? Because I will make one soon
@zudumalliКүн бұрын
Yes
@adityaplayz032 күн бұрын
can u add some buttons to steering wheel for horns,camera, etc
@adityaplayz033 күн бұрын
Hi bro, can u give me a perfect dimension of gear box top part and everything because I didn't get the pdf one
@adityaplayz033 күн бұрын
CAN WE INSTALL REVERSE GEAR ON LETF TOP SIDE?
@zudumalli3 күн бұрын
yes
@DilumNadiranga4 күн бұрын
ub lankaweda bn
@zudumalli4 күн бұрын
Ow
@adityaplayz035 күн бұрын
If every wires are connected to game pad then which wires we have to connect at 2 way screw board
@adityaplayz035 күн бұрын
If i connected wires from circuit pad to 2 way screw barriet than what i should cinnect to potentiometer and microswitch
@adityaplayz035 күн бұрын
Hi i want the proper connection part
@zudumalli3 күн бұрын
You can use RJ45 connect or DB connector. I have recently applied RJ45 Connectors. You can watch it in this video. - kzbin.info/www/bejne/f5qqf4CsZtiroJosi=x-RYq6qIm5ceT41K
@vinijoga1056 күн бұрын
Tem o firmware do wheel config? ✌️😊
@kulithasasen61557 күн бұрын
මම හිතුවෙ වෙන රටක කියලා 😂 සුපිරි ❤🎉
@zudumalli6 күн бұрын
❤️😁
@adityaplayz037 күн бұрын
@zudumalli I want manual gear box with hamdbrake and should we put the potentiometer in handbrake or only microswitch is good
@zudumalli6 күн бұрын
If you use the manual gear, you must use a clutch pedal. so put a micro switch on the handbrake. I have explained this in the description check it out.
@shreck22098 күн бұрын
bro, its look the deadzone really high. Can you fix it?
@zudumalli6 күн бұрын
no bro
@adityaplayz038 күн бұрын
I want to know about the potentiometer and microswitch and which one to install potentiometer or microswitch for handbrake? Or both we should install
@zudumalli6 күн бұрын
you can install both You have two options for how you play 1. (automatic gear or peddle shift + Analog Handbrake) 2. (Manual gear + Clutch + (Micro switch) Handbrake Or without a handbrake)
@adityaplayz036 күн бұрын
@zudumalli how to use it with micro switch and is it okay that we can use without putting potentiometer
@adityaplayz036 күн бұрын
@@zudumalli how will I know what switch I'm using
@adityaplayz036 күн бұрын
@@zudumalli I want the 2nd option and for the 2nd option what we have to do
@zudumalli3 күн бұрын
Brother, one of these two is used at a time. 1. (automatic gear or peddle shift + Analog Handbrake) At this time, the clutch paddle should be disconnected. Then the potentiometer should be connected to the handbrake. 2. (Manual gear + Clutch + (Micro switch) Handbrake Or without a handbrake) At this time, disconnect the potentiometer related to the handbrake and connect the micro switch related to the handbrake. Then the potentiometer of the clutch pedal should be reconnected. Then the handbrake and clutch paddle (key mapping) from the in game settings. Install both the potentiometer and the micro switch to the handbrake. 2-way screw terminals were used to make it easy to connect and disconnect these. check this out - drive.google.com/file/d/1RfccXfPocEKmYYBNjIDjAs3hHHrT5gRn/view?usp=sharing
hello there are multiple versions of the dc motor that you showed, so i wanted to know how many newtonmeters of torque you reccomended, is 1 enough or do i need more?
@zudumalli6 күн бұрын
One motor is enough for me. It depends on the size of the pulley and steering wheel you are using. But I also install another motor in the future.
@vale-mr3vf9 күн бұрын
I have an old racing wheel but the potentiometer i didn't know with what i should connect the third terminal in it to fix my racing wheel i connect with lx ? And to know in my circuit there is now ly
@zudumalli3 күн бұрын
connect to the Lx
@vale-mr3vf9 күн бұрын
Best explain stay doing this
@zudumalli3 күн бұрын
Thanks❤️
@DarkRange-vw2pn9 күн бұрын
Wich pulley and Belt would you recommend for my1016 motor?
@zudumalli6 күн бұрын
Better if you can use chain
@DarkRange-vw2pn6 күн бұрын
@@zudumalli yeah i used chain jts working good one issue im ghavin is when i apply Force either the steering Wheel gets Loose or the sprocket on the steering shaft gets Loose did you use anything Special to fix özür Steerung Wheel on the shaft?
@noseqponerpue11 күн бұрын
Hello Friend, I did the same procedure with the servomotors and it looked good with the tachometer, but in my case I added a speedometer, the speedometer with respect to 0 km and 200 km (maximum that I have in my cluster), is well calibrated but calibration must be done of each km and the truth is I don't know how to do it, the tachometer runs without problems, but an example is that in a game the car goes at 120 km and the servomotor is at 160 km or from 0 to 100, the game goes at 30 km and the cluster is at 110 km, it is out of calibration and I really don't know how to calibrate it, could you help me calibrate the speedometer or make a video on how to do it? I would greatly appreciate it😄
@zudumalli6 күн бұрын
If you have to untick something there, untick it and try. I haven't connected a speedometer to this yet.
@BrenoBP11 күн бұрын
Thats a lot of work. Congrats
@zudumalli11 күн бұрын
❤✌
@zehanplayz112 күн бұрын
awesome project bro
@zudumalli11 күн бұрын
Thanks 😊
@zudumalli12 күн бұрын
*TIP YOU NEED TO KNOW!* if you making DIY Gaming Steering Wheel (Important). Be sure to watch. kzbin.info/www/bejne/bXa8YnqmdqyDmc0si=PEOsDiciiBHmt72X
@zudumalli12 күн бұрын
*TIP YOU NEED TO KNOW!* if you making DIY Gaming Steering Wheel (Important). Be sure to watch. kzbin.info/www/bejne/bXa8YnqmdqyDmc0si=PEOsDiciiBHmt72X
@amacszoyuncu335512 күн бұрын
türkiyeden merhaba severek izliyorum encoder kullanmayı planlıyorum 900 dereceye nasıl sınırlandıra bilirim fiziksel ve anladığıma göre dişli kutusu kullanmaya gerek yok deyilmi?😊
@zudumalli12 күн бұрын
Thank you and welcome! The maximum rotation of the potentiometer is only 300 degrees. So, use the gear ratio of a fan gearbox and get 900 degrees from the potentiometer.
@amacszoyuncu335512 күн бұрын
@@zudumalli tekrardan merhaba ama potansiyometre derecesi 270 derece deyilmi? bide ben rotary encoder kullanmak istiyorum ona dişli sistemine gerek varmı yok mu?
@DarkRange-vw2pn9 күн бұрын
@@zudumallino he wants to use a Encoder but limit the Rotation to 900 degrees physically without motor and ffb if i understood it right
@DarkRange-vw2pn9 күн бұрын
@@amacszoyuncu3355sadece direksiyonun 900 derecede mi sınırlamak istiyorsunuz? Motorsuzmu yani Force feedbacksiz mi?
@amacszoyuncu33559 күн бұрын
@@DarkRange-vw2pn evet
@adityaplayz0312 күн бұрын
How did u connect the fan gearbox to thread bar and where to put 10k poteriinmeters
@zudumalli12 күн бұрын
Using glue gun
@adityaplayz0311 күн бұрын
@@zudumalli where did u connect the 10k potentiometer in the steering wheel and where the wires are connect in wheel
@FahimRaiyan2112 күн бұрын
What is the overall cost of making this?
@zudumalli12 күн бұрын
price cannot be said because I bought all the products locally. I only ordered the encoder.
@vitalii728212 күн бұрын
Hi, Have a problem) With this program in port 10 is always served 5v and motor always work in max, what could be, won't you tell me? Thank you in advance)
@zudumalli12 күн бұрын
in the wheel config software have you not selected the command mode as PWM +/- ?
@vitalii728211 күн бұрын
@@zudumalli no, selected PWM+Dir
@OkithaFernando-er3wt13 күн бұрын
Can we use any joystick
@zudumalli13 күн бұрын
Yes
@OkithaFernando-er3wt13 күн бұрын
OK. Thank you
@facunieto917013 күн бұрын
Thank you, nice video, like and suscribe you!
@zudumalli13 күн бұрын
❤✌
@adityaplayz0314 күн бұрын
What is the approximately price of this setup and I didn't understand about automatic with handbrake and clutch with no handbrake please reply
@zudumalli12 күн бұрын
check that video description I have mentioned about clutch and handbrake. price cannot be said because I bought all the products locally. I only ordered the encoder.
@adityaplayz0310 күн бұрын
@zudumalli hi bro but I want manual with clutch and handbrake too😢
@makhilpranav694914 күн бұрын
how much torque does your ffb wheel produce (using one dc motor )?
@zudumalli14 күн бұрын
4.9 N
@user-vn1ce3fq4z14 күн бұрын
Hello! I can't solve the problem. When connecting the power supply, the motor makes it a little difficult to move the steering wheel, although the spring and damper are at zero. I have a gearbox in my steering wheel, which also makes it difficult to rotate the steering wheel. Is it possible to make it so that the motor, on the contrary, helps to turn the steering wheel a little, but at the same time the recoil also works?
@zudumalli14 күн бұрын
Does it rotate freely without power? If so then it is a software issue. So reset the software settings and check again.
@user-vn1ce3fq4z13 күн бұрын
@@zudumalli Yes, without power it spins almost freely. I'll try to reinstall the firmware. Thank you!
@adityaplayz0314 күн бұрын
Hi bro how to handbrake and h shifter
@zudumalli14 күн бұрын
what do you mean how to connect or how to made?
@Deadloop_FF14 күн бұрын
I finally completed everything ❤❤😁 Thank you @zudu malli
@zudumalli14 күн бұрын
appreciate
@FahimRaiyan2114 күн бұрын
0:47 does the fan gear box needs to be new and working??
@zudumalli14 күн бұрын
This only requires gear ratio. You can use anything
@FahimRaiyan2113 күн бұрын
@@zudumalli thanks man ❤️ Love your work 🫶 outstanding 💯💯
@SubversionSecrets14 күн бұрын
Can i use this as sequential shifter? What all changes should i do
@zudumalli14 күн бұрын
It's hard, you have to change the mechanism too. it's possible with H-shifter
@SubversionSecrets14 күн бұрын
@zudumalli can u make a video how to make a sequential shifter from gamepad
@SubversionSecrets14 күн бұрын
Can i use b 500k potentiometer
@zudumalli14 күн бұрын
its too much but working
@SubversionSecrets14 күн бұрын
Potentiometer ohm?
@zudumalli14 күн бұрын
10k
@chaitanyapawar69315 күн бұрын
Bro all buttons are working but not only speedometer what should I do
@zudumalli14 күн бұрын
restart software
@jooniversalstudio575715 күн бұрын
Wait, I came here from the handbrake video tutorial to search the answer of how connect the handbrake to the computer. How to connect it?
@zudumalli14 күн бұрын
It is actually connected to the clutch potentiometer. Sorry, I couldn't mention ''clutch or handbrake'' in this video. check this diagram - drive.google.com/file/d/1RfccXfPocEKmYYBNjIDjAs3hHHrT5gRn/view?usp=sharing
@dimitrovoficial15 күн бұрын
So how do i remove IT for ets2?
@zudumalli14 күн бұрын
cannot
@levinhquang228516 күн бұрын
Third❤
@megustapescar116 күн бұрын
Maestro
@user-ry5qu6lh4w16 күн бұрын
Good luck my son
@zudumalli16 күн бұрын
Thank you 😊 💓
@juanbautistakala517118 күн бұрын
Hi! Could you tell me how I can adapt this diagram to an Epson L Series Printer encoder? Thank you!
@zudumalli18 күн бұрын
find the VCC(+) and GND(-) lines then other two connect to the Arduino 0 and 1 pins.