Let's Fixe All Issues In RFR Wheel Configuration (0.21) | DIY Gaming Steering Wheel

[@Motivatedclock]

Hi, im having a really weird issue the program only understands two position on the encoder, like i rotate the encoder all the way to the middle and the positions just changes from fully to the left to fully to the right.

[@MstrangerGaming]

Hello, I am facing every odd problem in this wheel configuration software, when I click on center wheel, the triangle goes either side over 450 degree, this problem also messing up the ffb because the center is somewhere else. Please help in this problem, if you ever faced it, if not then find for new comers

[@anaysunil]

Yes..Mee too..the centre wheel always gets changes during the gameplay..it's very hard to find the centre of the wheel

[@indianarts6369]

I'm getting wheel error 😢 give the solution for this

[@Manoj51XR]

Can i use STM32F411CEU6 instead of Arduino ?

[@vinijoga105]

Tem o firmware do wheel config? ✌️😊

[@JoeSmith-zv4ic]

Thanks for this video, I've got my encoder working but no force feedback (bts) using the + - I get nothing.. If i use the DIr I get motion only one way.. the BTS works both ways when I send 3v to each direction pin. Any ideas??

[@tgshreyas8702]

Brooo samaee errror occuringgg

[@vansanglam5230]

Sir, if I raise the steering wheel to 15%, I'll lose the steering wheel force feedback, how can it be misaligned?

[@zudumalli]

try at 100%

[@tgshreyas8702]

Brooo please helppp

[@tgshreyas8702]

Brooo iam facing annnn confused error please help mee... When ii usee ffb of wheel the motor only works with right sidee nott att leffftt when i movee... Power supplyy making noiseee and motor also not turning both sidesss please helppp

[@zudumalli]

same happened to me. It happened that on the Arduino board, one of the pins 10 and 11 was not connected. so check your these two wires.

[@tgshreyas8702]

@@zudumalli ok brother thank youu😊.. Whatt can i doo if same problem occurs

[@Harmansnation]

My wheel starts spinning continuously like crazy when I move it fully to the right side 900 degrees but if I do it on the left side there is no feedback to stop me. Please help me

[@zudumalli]

watch this video to fix continuously running - kzbin.info/www/bejne/emmqipaIj7Whlbcsi=NXdmFAJ8IYrjH9Sk If ffb doesn't work in one direction, it could be because one of the Arduino's pins 10 and 11 isn't connected correctly. Check it out.

[@Harmansnation]

@@zudumalli no the wheel isn’t spinning like this. It’s only when I move it to right side more than 450 degrees that it starts spinning like crazy. I have already fixed these settings

[@АндреевИван-щ7м]

Hello! I can't solve the problem. When connecting the power supply, the motor makes it a little difficult to move the steering wheel, although the spring and damper are at zero. I have a gearbox in my steering wheel, which also makes it difficult to rotate the steering wheel. Is it possible to make it so that the motor, on the contrary, helps to turn the steering wheel a little, but at the same time the recoil also works?

[@zudumalli]

Does it rotate freely without power? If so then it is a software issue. So reset the software settings and check again.

[@АндреевИван-щ7м]

@@zudumalli Yes, without power it spins almost freely. I'll try to reinstall the firmware. Thank you!

[@ESLAM-ALUMITAL]

Terima kasih, saya menemukan solusi yang tepat untuk masalah pedal secara khusus

[@AnimePhilippines]

How do i fix mine when i rotate my encoder its move slightly then go back to its original state its not rotating its just keep coming back to the center

[@bossoy0769]

Wire it up correctly dont have any free wire around that comed in contact with other wire solder it and use Heat shrink or a breadboard

[@AnimePhilippines]

@@bossoy0769 i already wired it correctly and i use breadboard to connect it

[@bossoy0769]

@@AnimePhilippines Thats weird it should work if u use a breadboard it was the issue on mine too it was shorted but if its still not working then i dont know

[@AnimePhilippines]

@@bossoy0769 ok thanks for your time

[@shyrose2790]

Can i use this app on other steering wheels like pxn v10? Please feedback.

[@zudumalli]

no

[@tgshreyas8702]

Ffb is only working in one direction not att other power supply starts beeping when i rotate

[@Randy_Mahendra]

I got the same issue and still looking for solution. And it’s still happening even though I’ve changed to a new arduino

[@jsmith0330]

Hi, is the wheel plug and play after configuring it? Like, will it work on other desktops without configuring it again? and regarding the dc motor, I would like to add another dc motor and wiring it in parallel with the other motor, is it safet to do? or should I add another bts7960 driver and add that to it?

[@zudumalli]

1. Yes, it is possible, but sometimes FFB does not work, so you have to reset the settings and do the configuration. (And before unplugging the wheel, the z toggle switch must be turned off.) 2. Other computers must have the necessary software before connecting. 3. Yes, you can connect in parallel. But this increases the temperature of the motor module slightly. And a little more power has to be provided. 4. Yes, the power delivery is improved by using two BTS7960 drivers. Just use two if you want it's not a problem.

[@ffdf-f3u]

bro for me the triangle and buttons are not showing ? i did all stepds still not working

[@zudumalli]

Is your arduino device shown below? This happens when your Arduino is not connected

[@Jackson_labely]

too much error

[@zudumalli]

what happened

[@jzayden]

May I know can add more button can make ya? It seems like in the wiring only 9 buttons in total allowed.

[@zudumalli]

Yes you can use Arduino Analog pins as buttons

[@jzayden]

@@zudumalli Thank you! May I know is it need to do additional coding? I see some tutorial using resistor with different value.

[@CPT_xjeet]

Bro can you make arduino nano steering wheel plss i have arduino nano pls make a video for me pls 😢 i dont get any videos of how to make arduino nano steering wheel i know you can make for me 😢 plsss Plssss 😢 😞

[@zudumalli]

no, it can't bro the firmware does not support other Arduino versions. That's why there are no videos about it.

[@CPT_xjeet]

Ok bro 😞

[@israeljmtd1667]

thank you for the info, i'm trying to build one my self and am in a delema to use between EMC light or this software, what do u suggest ?

[@zudumalli]

I have not tried EMC. I don't know if it supports any game.

[@kudasai_artem]

can i use potentiometer like encoder? how much ppr i need to enter?

[@zudumalli]

watch this - kzbin.info/www/bejne/bXa8YnqmdqyDmc0si=tFdSUhTofVFg5QgF

[@SujalChoudhary-s2h]

Bro you didn’t play ets 2 with this steering wheel

[@zudumalli]

soon as possible

[@nthchannel4924]

i have like the pedal calibrate and the wheel spin like when touch the wheel when calibrate pedal and i can't fix it :(((

[@zudumalli]

Disconnect the encoder from wheel configure and calibrate again.

[@nthchannel4924]

thank bro@@zudumalli

[@SATHEESHBALA-q7b]

it has been a long time POST VIDEO

[@zudumalli]

A bit busy this month. I will try

[@Naejtruck]

hi, Do I need the 1k resistors to run the encoder?

[@zudumalli]

A printer encoder is not necessary. Other encoders require

[@SATHEESHBALA-q7b]

bro is this support for all games in pc??????

[@zudumalli]

Yes, only some games have to be played through other software like (Forza, NFS heat). However, everything works through this software.

[@yagamingx2002]

Thanks bro❤

[@SATHEESHBALA-q7b]

bro can we use any arduino board for this ??

[@zudumalli]

no bro, firmware only supports to Leonardo board.

[@hum.ortales1753]

Bro my steering wheel is moving right and left very quickly even I move it slowly I used a potentiometer directly to the steering wheel without using any board's why

[@zudumalli]

Did you do the calibration with the ''windows game controllers'' and it like this happened? kzbin.info/www/bejne/fGnbmKaYisp4ZsU&si=oAfELxML-vcqeE2q

[@hum.ortales1753]

I don't have Arduino bord how much does it cost if we can use Arduino board then that is the use of using Joistick board

[@hum.ortales1753]

Can I can do without that

[@hum.ortales1753]

@@zudumalli no

[@hum.ortales1753]

Can we use mouse for steering wheel

[@RealRenko]

bro you sri lankan?

[@zudumalli]

Yes

[@priyangaediriweera5807]

❤❤❤❤

[@sarigamasongbox584]

Thank you❤

[@zudumalli]

You're welcome 😊

[@SATHEESHBALA-q7b]

is dc motor is definitely needed for this ?? 🥲🥲

[@zudumalli]

no, you can use it without motor but no force feedback.

[@SATHEESHBALA-q7b]

Ok bro