TanFK

Пікірлер

@ramonmelofpv 19 күн бұрын

Well done!

@jandomingo9806 24 күн бұрын

This flies great with 2004 2400kv 6s motors. With supafly preset without the filter.

@droney_baloney Ай бұрын

bluetak will pull anything and everything out of your motors and bells.. no brushing... no shower... easy peasy

@duncanpope2899 Ай бұрын

Have you tried it on 6s with bi blades and 6 inch props on the bottom? Curious for compacts heavy lifting drone

@luisbarron3956 Ай бұрын

I had a GepRC naked GoPro 11 that would power on just fine, but one day randomly refused to start recording no matter what I tried. I was unable to reinstall gopro labs firmware because it was stuck in a reboot loop. Finally I installed the original gopro firmware manually and it worked, but then I landed where you were with official firmware. This tutorial is exactly what I needed, and worked perfectly. Cheers!

@Xcx284 Ай бұрын

Ur running 6s on a 2000kv. That’s a super trust

@TanFK Ай бұрын

The weight of this thing carrying the geprc naked gopro is quite heavy, so it needs the power. When stator size and drone category and prop is smaller youll need higher KVs, I.e 2.5 inch cinewhoops go with 1404 3800kv (4s) Vs 5 inch freestyle 2207 2400kv (4s)

@Xcx284 Ай бұрын

@@TanFK what do u think abt 5inch using 2207, 1900kv 6s? (Dji03)

@TanFK Ай бұрын

Sounds ok, Im running one quad with that parts, Just gotta have 50+amp esc to accomodate voltage spikes and crashes. It was too fast for me so i ran a throttle limit about 85% get it to feel like 1750kv

@Xcx284 Ай бұрын

@@TanFK I see. Well I was also looking at a 50A speedy F7 V3 stack. But the 60A f405 V4 seems tempting also. So that’s why I’m kinda stuck within these choices. Which stack and motors to use. The 1700kv motors is also in option.

@TanFK Ай бұрын

The speedybee v3 50amp should be enough bro. Id rather buy two speedybee v3s so i can swap them when one breaks. Cuz voltage spike when crashing would even kill a 60a esc if the crash is hard enough 🤣

@CJINPARADISE Ай бұрын

can i install gopro labs to my an external battery work with out the go pro battery in the battery slot? Without taking it all apart???

@iamagob Ай бұрын

love sound test. unfortunately, i want to see compare sound test between pico and pavo20 pro.

@OSAMALENS9 Ай бұрын

Thanks a lot man

@Fpvjoe Ай бұрын

Hey man, thanks for your video, I’ve got a GoPro 12 I’ve converted to naked. When I try install the GoPro labs it keep rebooting and flashing screen. Doesn’t ever show installing. I’ve tried working a 6s battery plugged in through the balance cable and also through plugging the old GoPro battery in

@TanFK Ай бұрын

Maybe try reinstalling the official one via SD Card and try again? gopro.com/en/us/support/hero12-black-product-update/windows

@normellow Ай бұрын

Change your bearings.

@nugrostv4600 Ай бұрын

This issue hapen with me now ...

@TanFK Ай бұрын

Does it happen even if inav or betaflight ah bro?

@nugrostv4600 Ай бұрын

@@TanFK my issue is cable lossed from board .... i fix it already by re soldering

@TanFK Ай бұрын

@@nugrostv4600 good to hear you manage to solve it. The gps wires that come with the packet is sometimes low quality. So problems can come from them

@DH-bc6im 2 ай бұрын

Detailed step by step vid! Thx a million. 😊

@throyest4832 2 ай бұрын

Can the dji fpv controller 2 be used with this?

@TanFK Ай бұрын

I found this video. Hope it helps your scenario kzbin.info/www/bejne/eXSZhJp7rd-Kac0si=68xExrfZuYiq_kKZ

@captmohmadabdullah2577 2 ай бұрын

Thanks Sifu, really helpful. Remind me my quad fell into the sawah padi totally covered in mud. I did unplug the lipo underwater; washed sprayed contact cleaner; dissembled and dried everything. All work and fly fine except VTX intermittent interruption .

@TanFK 2 ай бұрын

Damn bro better replace new vtx. I also had the same scenario and totalled the drone because of vtx failure.. you flying analog ker?

@captmohmadabdullah2577 2 ай бұрын

Both Analog and digital. Yg jatuh tu analog, ; agreed need to change vtx, may be later swap with vista. I saw you footage at Pandamaran sport area, I previously stayed at Port Garden (Kg Raja Uda) just opposite sport centre. but after PKP returned to my hometown in Penang

@TanFK Ай бұрын

@@captmohmadabdullah2577 ya bro i totalled a drone cuz i fly vtx after water damage and it just died after arming 🙂‍↕️ Yeah pandamaran sport area best for flying cuz alot space. Hope penang u found some nice spot for fly bro

@rifaldychannel8668 2 ай бұрын

Mantap bro salam kenal salam satu pilot 👍✌️

@TanFK 2 ай бұрын

Thanks bro. Apa khabar, nk main fpv pun ker? 😎

@KainniaK 2 ай бұрын

fun fact it's actually impossible to bring any battery down to zero volts as volts is just the difference in potential, and the chemicals will always have some potential between them.

@TanFK 2 ай бұрын

thats true, i always see one or two cells that stay at 1.xx volts. While the others might be low but not zero

@DigitalCruzer 2 ай бұрын

Great video! Something else to be aware of, the contaminants left from water can cause corrosion to start but not cause issues right away and can kill a component randomly several months later even though it was working fine after the plung and drying, this is actually why you want to use the IPA to actually clean the electronics, removing camera housing and all that, don't just thoroughly dry everything, hope fir the best, then try flying it... It might seem fine, but could suddenly drop out of the sky 6 months later on someone hurting them... I had one that spent months in a tree before a storm finally knocked it out, everything worked fine for months, then it finally died mid flight, upon inspection corrosion slowly built up under the components, just took time for a problem to develop, washing down with IPA seems to help that, i also use vip camp dry occasionally on my electronics, the silicone coating helps replel any rain drops i might fly though and its easy to just give everything a spritz occasionally the night before flying

@TanFK 2 ай бұрын

thanks for sharing. I've experienced similarly with some electronics being fine momentarily. I'm curious to know more about cip camp dry, whats you're experience been like? like does the solution harden and have to be cleaned occasionally and all that?

@neuromancer692 2 ай бұрын

There is no point in destroying the battery if it wasn't overly discharged while underwater. They are a sealed which makes them pretty much waterproof.

@KainniaK 2 ай бұрын

the tabs can corrode super fast in salt water. Just 5 minutes in salt water is enought to ruin any battery.

@Rob1656 2 ай бұрын

Great information

@hjlkqepq1203 2 ай бұрын

very helpful. Just here to point out that in 5:04 it’s the small resistor to measure current.

@TanFK 2 ай бұрын

Thanks for the correction!

@MrKaleidoscope 2 ай бұрын

fuck yeah dude

@TanFK 2 ай бұрын

✌️

@yurasmile7943 2 ай бұрын

Have the same issue with go pro 6. Have installed 1.6 firmware but still face this issue. And as I can see there is not GoPro labs for hero 6. Don't know how to fix it...

@TanFK 2 ай бұрын

hey man, I just checked. On the gopro website the latest update is 2.1. Give that a shot, hope you manage to fix it. gopro.com/en/us/update/hero6

@weslisahum 2 ай бұрын

Just build the GoPro 11 in the geprc case. Now nothing related to gyro seems to work :(. can't use hyper smooth. But also cannot get motion data for use in Gyroflow or real steady. Did you happen encounter this before?

@TanFK 2 ай бұрын

if i were you. Id try maybe using another SD card, i use a sandisk extreme (red and gold) if your running higher write speed sd cards then good. If that still doesnt work, maybe try factory resetting the naked gopro in gopro labs ( !freset) then reupdate and install gopro labs again. Thats all i can think you can try atm

@weslisahum 2 ай бұрын

@@TanFK⁠thanks for your reply. Tried all of these. Maybe its hardware. The imu. Another thing could be that its stuck in tripod mode. But in labs cant find an option to make sure its off

@TanFK 2 ай бұрын

Yeah as much as i wanted say its a faulty gyro, i think its better to try all you can. Naked gopros are not warranty claimable 🥲

@weslisahum 2 ай бұрын

@@TanFK yeah agree, i keep trying to

@cutfpv 2 ай бұрын

Nice video mate. I’ve also been struggling with all the jitters from my cinelog25 whenever I add my naked gopro on it. I think that I am not being able to get my gravity center correctly, as battery can’t be pushed back to balance with the gopro. And I believe it affects my pid looping forcing my fc to be always making lil adjustments while Im flying. Causing then these micro bumps that I don’t have on other quads. But I can’t tell for sure 😢

@TanFK 2 ай бұрын

It could be overtuning. Maybe dial down your PI balance and I term little by little during a pack and see if it helps

@cutfpv 2 ай бұрын

@@TanFKcheers. Will give it a try

@weslisahum 2 ай бұрын

you are such a life saver!!!!! thank you!

@TanFK 2 ай бұрын

Happy to help

@weslisahum 2 ай бұрын

@@TanFK unfortunately i am now running into a much worse issue. Both gyro and hypersmooth seem to be shut off. When I enable hypersmooth nothing happens in camera. Everything still shaky. And when I shut off hypersmooth (and lens wide) gyroflow does not see any gyro data being recorded. Also in realsteady it complains there is no motion data. I am totally clueless after two days troubleshooting. Do perhaps seen this before?

@TanFK 2 ай бұрын

@@weslisahum if i were you. Id try maybe using another SD card, i use a sandisk extreme (red and gold) if your running higher write speed sd cards then good. If that still doesnt work, maybe try factory resetting the naked gopro in gopro labs ( !freset) then reupdate and install gopro labs again. Thats all i can think you can try atm

@bangarangJones 3 ай бұрын

That pliers bending method, genius. Tape to remove metal shavings from magnets, genius! New motors are nice, but if i had to buy a new motor every time i flew into some concrete I'd go bankrupt.

@glennlapuz5168 3 ай бұрын

Can I copy your PID Tune?😢

@michaelj4420 3 ай бұрын

Well presented. Thanks for sharing

@EricD7 3 ай бұрын

nice video i like the format

@fklotaloi 3 ай бұрын

Wow I think I have learnt something from this video. Thanks.

@nugrostv4600 4 ай бұрын

Great sharing bro ...

@mouahrewam 4 ай бұрын

Yep usefull :) thanks

@NathanKimble 4 ай бұрын

Not advice that I care to follow, based on the fact that he fan dried his electronics, right after giving his drone an old fashioned shower in his bathtub! Can anyone say "rust",??

@DanielBarrios83 4 ай бұрын

Good video dude

@magiliangaming 4 ай бұрын

DO NOT brush motor coils with a metal brush! the wire has a layer of silicon(e) to prevent the wire from shorting out on itself!!

@lionelttl 5 ай бұрын

Ah another Klang boy. Which high school you went to?

@TanFK 5 ай бұрын

Hey bro. Am from ACS. How bout ya?

@TamVO-ez9zc 6 ай бұрын

Hi bro, my one is the first gen Tx16s. So i have to buy the ELRS module to bind with the pavo pico, right? do you have any recom for module? pls. is it should be fine BetaFPV ELRS Micro TX or (V2) Module 2.4GHz

@TanFK 6 ай бұрын

Hey bro. I’m using the Radiomaster ranger micro. I bought it with the bundle with three receiver. Good value. Been working good for me Your mention of the betafpv elrs micro tx: it will also work. The term ‘micro’ is the correct size of module for the tx16s. I personally never tried but should be ok.

@ToniHecht 6 ай бұрын

thank you, very good explanation. is the o3 air unit compatible with the dji googles integra?

@TanFK 6 ай бұрын

yes. on link below for the integra, o3 air unit is listed under supported products: www.dji.com/global/goggles-integra/faq

@Twangaming 6 ай бұрын

Great video! Should have 10x the views

@thetechnovator6768 7 ай бұрын

So … I messed up. Exactly what you were worried about… I stripped my screw and now I am clueless as to how to open the bell as there is a piece of junk inside ta motor which I need to remove. Pls help

@TanFK 7 ай бұрын

Try searching stripped screw guides. Ive seen The rubber method alot but it didnt Work for me. I normally Cut The screw with a mini hacksaw And use a - screw Driver to get it out

@tasty-lab 7 ай бұрын

do you need separate screws for the motors to sit comfortably on its thick frame? im thinking of getting xilo stealth 2207 motors and i dont know if their screws are long enough. thanks

@zafhastrans2000 8 ай бұрын

Is it possible to using speedybee f405 v4? Because in their description it's support 8 motor

@eddie_Za 8 ай бұрын

Link on that cool plier..

@lovemonkey9982 8 ай бұрын

Like your presentation, btw what was the total weight of the dslr including lens ?

@chrisB_OG 9 ай бұрын

0.16 was the best version? I think that’s what Ciotti was sayin’

@averagefpv9449 9 ай бұрын

Great content. Very useful. I'm subb'n ya bro!

@luisLP5752 9 ай бұрын

Do you think that a AIO that uses mount holes of 30.5x30.5 would fit in this frame? I have a 3d print part for the conversion of 30.5 to 26 or 20 mounting holes. Aio itself measure 38x38

@fpvkevlar8101 9 ай бұрын

Good video. Thank you for he great info

@vitale6633 11 ай бұрын

Great Video - Thank You for sharing !

Ең жақсы KZbin

Пікірлер