Can I still run my equalizer with a dsp?

Why don't you build a 5.25 speaker like this. The Honda Goldwing guys will love you.

Does this unit have effects like hall and live

Mine still pop with the prv 2.4 when I got to EQ and pick bass boost every time it turns off it rests even tho I try to save it on memory?

NO HELP ON THIS PAGE, KEEP SCROLLING ELSEWHERE

Will this add bass to music that doesn’t generally have it? Or is very low like some country music or rock even?

Does the 2.4 not have the preset xover feature?

Just bought a DSP2.4 for a home audio system. The idea was to use it to feed six audio amplifiers for a set of three-way speakers, and one more channel for subwoofer output. So I need this DSP unit to first send A signal four ways into the red RCAs of the four outputs, and B signal to the white RCA's four-way also, before crossovers and EQ's were configured. Is it possible with this 2.4 unit?

Would i need 6 outs to use this with a 4 channel amp and a subwoofer amp using 1 subwoofer ?

Is there an aluminum waveguide horn to fit this?

What is the voice coil size

6000 what 😮

I wanna use these in my PA system!

Can u tell what good crossover to 😮 put a set deaf bonce Sylvesters 6.5 midrange speakers they don’t like to much bass, I listen to a lot of rap music?

Como posso adiquirir ?

Onde consigo comprar alguém me passa o watts de um vendedor

you are very knowledgeable about the device itself and how to work around the settings, but you explained in the input parametric eq wrong, specifically the Q-Factor the tighter or the lower the value the more that will affect neighboring frequencies and the looser or higher the number the the less that will spread and affect neighboring frequencies. if you want to cut 63hz frequency or boosted without affecting 50hz or 80hz you will choose a higher number... but if you want round out more evenly and lower or boost everything around the 63hz you will go with a smaller number.

been using a 2.8 for a couple of months now. This morning while driving to work channels 1 and 2 emitted a 'tone' id guess about 5kz at high volume. I could not turn it off. if i turned my radio vlume down it did not matter, as i have narrowed it down to the actual DSP sending out the signal. I was luckily enough able to safely get to the side of the road and tunr the vehicle off. When i restarted the vehicle, and when number 1 amp turned on (channel 1/2) the tone came back on and i had to go into setting and turn the amp off. this was so loud i could smell my voice coils. So not only are my ears ringing, huge headache, i probably have burnt up mid/tweets because of it. How do i get this fixed? And how do i know this will never happen again? @PRVAudioBrazil @PRVAudio @PRV

If using a stock head unit with a LOC can I just wire this up in line with the LOC like say for instance... Head unit to LOC to DSP to Amplifier reason I'm asking is I don't know much about installing and everything is already installed and working I'm just wanting to add this to clean up the signal for better clarity

I seen it had a hpf, but does it gave a LPF?

I wish there were videos of these and the other new prv products I've searched and haven't found not one plz demo these and all the new prv products

Alguien me puede decir cómo se llama ese tecno

So you going to read the manual for 2 hours just to set this thing up once way too much stuff going on for the average consumer.

esas bocinas son una porqueria . compre un par y el cono se rompio. las bocinas de desbarato

My first two channels are for my front door 6x9s that are ran in parallel with the dash tweeters. What do you suggest the settings be for that? I want some mid bass up front but don’t want to blow the tweets. Please help. 6x9’s are JBL GTO939 100 watts rms each. Tweets are Skar 3.5 150 watts rms.

To dam difficult to understand I bought one and I have to sell it back

Great video. Now time to install one on my car.

Mere ko aapse baat karna hai

I have 6 6.5 and 2, 8'' speakers with 4 DS18 tweeters that I'm changing to 4 PRV's tweeters om my 2009 Harley Davidson Electra Glide Ultra Classic, there all are carbon fiber, them are the best ones I done put on my bike...

I purchased them for my road glide wish someone was running them already to get a opinion

E 6 polegadas ou 6,5 polegadas real

Tim give some info how to use the expert px2

I can't wait to buy this and try them out

Thank you

nice to see a DSP that doesn't require a laptop to use! having said that, there are things that could be better. ditch the stupid EQ presets, and use the processor power for more EQ bands. if you want SQ, a digital input of some kind is needed. a port for an (extra cost)external display would be a nice, allowing you to set the system from the driver's seat. all in all, looks excellent for the price.

Does it have EQ settings?

what does the bt and lr portion actually do

Hi to connect the sub and the med with only one rca?

Thankyou Sir!. Is it possible to configure my subwoofers to selectively receive specific bass frequency ranges, such as 30-60 Hz and 120-160 Hz, using the DSP?

😂 but there EV mids bro not PRV 🤣🤣

Great job 👍🏼

Why all my lights red on mines now

Humacao!!!

This seems like a well-sorted device.

kzbin.info/www/bejne/j5CmfZt5r7CfZ80si=nevvkGOTm81S6B_e

kzbin.info/www/bejne/j5CmfZt5r7CfZ80si=hGsXi7wTLW_vzrlL

Currently have a 2021 challenger with the stock head unit I’m running 2 amps and a battery pack with 2 kicker 12s all ds18 on the mids and highs I already have a converter the lc6 or 7 can’t remember would I need this if I already have a converter ?

Where available please tell

Do you accept bulk OEM orders?

Is this the best way to tune it?