thank you for the clear instruction, well done!

A good start but there's more to it than that. Your prop could be hub heavy the way you done it.

ENERGY VAMPIRE ALERT!!

I want to warn that the link in the description now leads to fishing and scams, I'm guessing the domain ran out and bots found it and made it redirect to malicious content

Hey could you please help me I'm at this stage now and when I enter calibration mode the pixhawk has a long beep i put the throttle down, however i dont hear a tone from the motors. they just keep beeping normally. I'm unsure why they aren't making the calibration dial tone. I am using readytosky 40A escs and readytosky motors. do you think i need a bec

Thanks for your video

Just bought one of these. Excellent video. Many thanks.

I've been having issues uploading mine to the software

You are wrong If the 4 motors rotate CW then the Drone will rotate CCW and VS

What happens to pitch axis when the quadcopter rotates around roll axis. Does the reference pitch axis also rotate with roll angle?

Hi, I have FSi6 Transmitter and FSi6B receiver. I see ppm/ch1 in my FSi6B receiver. I have enabled ppm on rx setup of receiver. And it is connected to RC port of pixhawk 2.4.8. I am not able to do ESC calibration through pixhawk for one motor which is connected. Do I need ppm encoder to connect from FSi6b receiver to pixhawk? Do I need to setup any parameters on the pixhawk using mission planner? Am I missing something here?

Can I use 9 channel receiver with 6 channel flight controller, like FSTH9X with KK 2.1.5 flight controller.

Is it necessary to do

Great information fabulous photo viewing, clear concise explanation. Hope to get my Alpha in the air soon. Brushless replaced .049 Golden Bee Cox Glow engine.

Great video...but like oking for more detail...like, how the flight controller manages commands and also interprets sensors(?) to offset turbulence or erratic user commands to maintain stable flight...also, to countter over correction...

Any idea how you get this to bind with a mini reciever having problems and can not get it to connect

K.I.S.S. approved for people like me. Very clever - thanks!

I think your explanation on YAW moment was wrong, pls check it.

Well explained, thank you !

kzbin.info/www/bejne/qYCalpuDjp1kp7c

Thanx

You are so smart and so awesome thank you very much for the tips

To the man in the video …. YOU ARE A VERY VERY GOOD INSTRUCTOR MY FRIEND ! ! ! ! You presented the information from a very basic starting point and made it very easy to understand. You get 5 STARS for being considerate towards your audience. We need more men like yourself as an instructor on ALL things engineering. Keep up the very good work. You should be a teacher of engineering...

What

My rc in port of mini pix is different from the output wire of ppm encoder the white pin don't fit

not clear.. hope for better explanation

That's a great balancing tip but I would use transparent nail polish. By the way, love your missing tooth.....

🗑 get in

Trash

i am working on this project,but your site is not opening,it says that the site doesn't exist.

Sir how can I get a radio like this am from Nigeria, I need your response thanks sir.

its not a thumb screw... its not even a screw... call it a roller switch or something.... its basically a sideways encoder switch like on modern car radios. Its just housed to be like a roller wheel rather than a dial. Also i think everyone can figure this out within the first 10 minutes of holding the transmitter.. do more intermediate and advanced tutorials. like the dual rates/exp , throttle curve, pitch curve, etc if someone cant figure out how to change the models name without instructions they're pretty stupid.

If you don't have a nail polish

can i bind a force1 f100 to a , FLYSKY i6x transmitter. need help thanks.

Looks like its flying with a dead battery.

Very informative Thanks

fantastic idea with the nail polish!

good job 👍

It sad that your website is no longer in business...

I was hoping to understand how the drone stay in the same place in wind

provide the code to generate the ppm signal in raspberry pi

your website is not working!

i have understand many things through this tutorial, very helpful, thanks sir

I must however take umbrage with your last statement. An equal number of motors (clockwise and counter-clockwise) is not necessary for stable flight - only a parity of dynamic mass. Right? (picture a single rotor helicopter)

Thanks for this video. I tried to explain these dynamics - to several people who claimed to be experienced in Quadcopters. They wouldn't have it! : )

I'm doing some tests with a drone x8 + 3DR, in an experimental platform, I want to try only movements in the angles roll, pitch and yaw, but I need to avoid that it rises, someone knows how to deactivate the Z (height or elevation) in the pixhawk, I just want to move the angles without the drone starting to rise, you know how to deactivate the autopilot part of Z could give me information. thank you I await your comments

Excellent job sir...

So how does a quad copter flip? They seem to do it so fast.

I honestly thought specifically yaw was controlled by the motors tilting in a circular pattern lol

I appreciate the time you took to make this video. Thank you for the explanation.