Thank you for spending the time to create this contraption. It helps seeing things all connected in one place

Can it be turned off ? I don't have Wi-Fi in the home I don't want to connect it to my phone I just want to turn the stupid thing off

Successfully completed bearing change on an old ELU , which is basically the same router. Thanks for the video , wouldn’t have got it done without it 👍

It's probably 23 volt because there are some capacitors in the adapter, right?

Thank you so much for this. Mine was drifting as well, even after resetting the knob.

Nice job. It should be noted that most newer GFCI’s can accept the two wires under the line screws. Just be sure to make all wires very tight. So there is no need for the pigtails. Also be very careful when doing this because your initial GFCI may have multiple sets of load wires leaving and going to your garage, laundry room, or exterior receptacles. You want to make sure that any of those other areas don’t loose protection or become redundantly protected.

I have 2 black wires from my old gfci, and 1 white. I connected them the same as old receptical, but got no power. Could I have put the black in wrong spots, or white. There is a light switch next to this also

Mine the lyric thing spins then shuts off, how do I turn this dumb thing off

Thank you . Excellent Video. Just replaced the bearings on my old ELU MOF177E. Extrra care has to be taken when removing the on/off switch as i broke the thin plastic connection while dismantling. was quite expensive to replace.

Good point about the tolerance of the lower bearing. I have an old Elu MOF96E Type 2 for which I just ordered new bearings. The lower is an NSK 6003Z, upper is NSK 608Z. The 6003Z comes in two variants, 'standard' and C3. The C3 is a looser internal fit allowing greater thermal expansion. It is slightly more expensive. I would have bought NSK from a bearing supplier, this being a brand I trust. However, I became unsure which type is correct for my router. So instead I bought itemised MOF96E spares from a tool specialist. This meant I paid a bit more and could not choose the brand. I await delivery, fearing Chineseum engineered to die on warranty period + 1 day, not the 30 years I got from 1991 vintage NSK.

Nicely presented.

Thank you! My Domino has been out of commission for months because it drifted constantly. With your fix, it performed like a champ today. You saved my $1000 investment -- Cheers!

Thanks so much for the great video. Bearing failed on my Swiss made DW625 I bought ages ago. Works like a champ now!

Why did you use pigtails? Couldn't you just use the wires from the box to the Gfci? Where did you get the pigtails?

How do you get the app to set the thermostat up?

I hate the fact that you need the app to switch between the fan being on/auto. You can’t do it through the thermostat manually, specifically when they’re doing maintenance on the app, is completely inaccessible.

I have a question cocnerning the speed adjustment. I have an ELU MOF 177 which is practically almost the same machine as yours.Since my speedcontrol broke I went online to order teh spare part. However when coming upon the parts list I noticed that it's not supposed to go on top but rather beneath the upper bearing. When I opened up the machine for the first time I found it in the position you're describing. I checked the parts list for your router now and it also says it should go beneath the top bearing. Nevertheless I went ahead and assembled it the way I found it. While it runs when I use it in handheld mode, the speed control does not respond when the router is mounted under the table. This is probably due to the fact that it only sits loosely on the shaft and probably falls off when turned upside down. On my DW621 the speed contrl sits really tightly on the shaft, in fact so tight you can turn the shaft by turning the speed control. Now I was wondering: If I mount the speed control in the position indicated in the parts list, I wont be able to properly mount the top bearing! WTF!? I hope somene can make sense of this. Thanks. PS: Here's the part's list: www.wmv-dresden.de/documents/ELU/mof_177_e_b_type2_fraesmaschine_elu.pdf www.wmv-dresden.de/documents/DeWalt/dw_625_e_a_type4_fraesmaschine_dewalt.pdf

THanks !! you deserve much more likes !!!

Hi anyone looking for bearing sizes before stripping their router !.:- - top bearing -nsk 6201vv Bottom Nsk 6095vv, thought this might be useful..👍

Easy to install, kzbin.infoUgkxjA-hDN2m8_mi0Dg0JD8U6QiArozIAc4I and comfortable. No idea what other people were talking about when they said it was difficult to install or uncomfortable.

I have the DTS 400 and love it. This will be my next one.

Does anyone know where i can find the magnetic ring on top of the armature please? I lost mine :(

I've had mine for a few years. Came in after work and it was dark, the removeable face was VERY hot. I pulled it off the wall. Watched a few fix vids but opted rather to just get a basic Nest.

What should I do if I get an error when registering the thermostat, it tells me that it was already registered with another user?

Turn the volume down when operating the tools!!

Nice work enjoy the video

How do you access the Em. Heat options if say the primary heat pump outdoor unit fails

i don’t see the heater sign, can you help

You mentioned taking dust extraction down to about 50%, I run all my sanders at 20% (lowest setting on my CT MIDI) except occasionally my Rotex 150 when taking down material, they I might go 40%

A complete explanation of why the GFI outlets are wired the way they are is necessary!

I agree all tech sucks on document/ instructions, paper copy every time

Airgun has like knockback 20000

Nice Stabila Level....prolly cost 1/2 of what the Kohler did. ;)

Thanks. This got me through disassembling a MOF177, which I am restoring.

Thank you for taking the time to make and post this video. I was struggling to figure out the best way to remove the bearings. Sadly this router is discontinued and Dewalt doesn't make one this big anymore but you can still find parts! Been a great router for the last 20 years!

That was a no no as you aren’t supposed to alter the domino when it’s switched off, I’m not being a smart alec just repeating what domino state

Didn’t think you were suppose to adjust width of cut with machine off?

I just got a new df 500 yesterday and was getting drift with large dominos in a waterfall miter. I will give this trick a shot. Thanks!

Thank you for sharing this. I have a newer style domino and I was having drift issues too. A quick trip to a bike store and no issues with a big batch of mortises. Cheers!

T stat is a piece of junk. 2 yr old and it keeps saying, connecting everything I twist to change temp

Do it yourself, visit the Stodoys website and find out how.

Exelente video Consulta mi bebe hecho un tornillo por el lado del aspa del endusido la y seo. funcionar y saccc se iso pedasis Puedo cambiar solo el aspas que es un plastico????? Gracias Puedo Puedo remplazar el aspa solamente

I know this video is 8 years old but how do you like that Domiplate? I’ve been thinking about getting one

Awesome! This is super helpful! My mind was struggling for a minute, figuring this out. Thanks!

Excellent. Thank you!

Thank you sir!

Thank you for these two videos! I have a Trend T11 (which looks identical to the Dewalt 625) and it has damage to the lower bearing housing (the bit that supports the table height stud). I bought a new lower bearing housing, but just had no idea how to get the router apart! This was awesome - thanks...

Excellent video! One of the most articulately explaned videos i've seen!

Not many people have an air compressor at home

Excellent