I just wanted to know what this involved. Thank you so much for sharing this. Great video.

Can the boot be replaced without taking out the piston? I can’t get the piston out, I have the boot around the piston sealed at the top but cannot get it to seal at the base back in the caliper

Legend!! Thank you 😊

Thanks for the video. I definitely would have given up without your help. Initially it looks impossible but with perseverance, bloody knuckles and washing up soap I got in and it works!! Thanks

Thanks mate, needed a quick one to remember what size the nuts were!!

Nice video cheers

Yes brilliant!! Thank you. Hoover like new….😅

Thats not rockwool that fiber glass for lofts

what is thinner ? White spirit ?

L8

Perfect I’ll try this tomorrow Thankyou All the flights are flashing only had it 2months !

Very helpful cheers matey

Good video, but shouldn't you take the opportunity to lubricate the caliper pins while you're at it?😊

Brilliant video. I have the later version of the heater control. I just replaced the hot/cold control arm yesterday. I sprayed some silicone lube on the diverter valve in the engine bay. It was quite stiff and probably contributed to the end of the control arm breaking.

What if spring handle is broken what to do ..

Muchisimas gracias la saque a la primera quitando los 4 tornillos grandes del 18 y luego la desmonte para pintarla .

Bonjour il faut changé la pompe pas je comprends pas la Lang

Thanks just saved me returning my tassimo machine this morning

Glad you got there. I just put it in socket like you , but with the black collar at the termination simply measure from wall to the black collar, then whatever that measurement is, is how much too long the flue is, so take that measurement and reduce the flue length by that figue.

It’s a clutch master Not brake master

Would help others to show if mk1 or mk2 ka just to confirm

You could fill the new oil filter up with oil before putting it back in as well.

This actually gave me the info I needed so thank you, but why on earth did you go through the other type of lock TWICE. Keep it short mate - only talk about things that are important to the task and speed the video up when you are doing things like screwing & unscrewing.

I thought its mandatory to change the disc too always with the pads

helpful guide

How can I get the furthest screw out in the wheel arch any tips

Thank youu!!

Thank you for the video, just changed handles & worked a treat!

Thank you so much for uploading this video! You’ve saved so much hassle and it’s worked straight away! 🎉

Great video. You're missing the rubber seals on the handle...

Nice one. Very useful video. Thanks for sharing.

If you had your softener for 13 years, it got slow because your resin beads got old. As they get old, they get mushy. And instead of little balls that allow water to pass through them, you get something that looks like a mud. Putting a caustic soda into your tank solved the problem, bacause you completely dissolved them and you got rid of resin through your drain. Now your tank inside is empty and your water is just as hard, as without water softener. This is an old video, but hey - please don't do that. There are ways to regen your water softener. You just destroyed it.

Well done dude

Great video. How much would you charge roughly to do this ? Debating whether it’s cheaper to just get the 2 jacks and do it myself

This tip worked great. My machine is back in operation. Thank you

Did you pull the drivers seat out?

I'm thinking of changing the ignition coil on my 2006 Ka, just because I doubt it's ever been changed and there's a slight hesitation under load, it doesn't like being given full throttle when in a high gear at a low speed. Would you happen to have a part number handy for me? Appreciate the video!

Thanks mine didn't have a leaver to take the wheel off at the bottom, I had to pry it open with a butter knife and then hammer the pin back in afterwards.

Thanks for the video very instructive

Thank you, very helpful, the instructions are lacking.

This is very good job, but how you atest roof for registration?

Omgggg thank you!

Great little video.. laughed when you knocked the camera over that’s me too! Not easy filming and ‘doing’ at the same time.. I’m investigating a serious fluid leak and removed my master cylinder esrlier today. Something is seriously amiss hoping that I can find out what’s happened.. ..

Cheers, just fixed my bottom oven thanks to your help. Nice and easy straight forward instructions.😇

Thanks for the video mate 🙏

Thanks for tip I was about to launch the machine of the roof

Sorted me right out. Thanks mate ❤

mine doesnt have screws on the head :/

how do you put back in

Thanks! Couldn’t figure this out but all became clear with your video. Handle fixed :)