I did the front 2" drop on mine today, but had to compress the spring a lil to get the top on, no spacers, that normal?

Amazing job, what a clean and comfortable way to work. I have an astro van with a 4.3l 95 same block different fule system, have the sheetee spider injectors. Can you tell me howany knock sensors ahoud have i have 3 and I don't know if the past mechanic just plugged in something random. I have some issues with knocking in the intake manifold white smock at start.

What tlrelay harness do you recommend for a 06 tbss to run this setup

Great teacher....thanks for the great instructions.

Every website says part # 5745235040 is discontinued and no longer available for purchase. Surely there is a crossmember sitting around on a shelf somewhere. Any suggestions?

A local bodyshop fixed mine for $300.00

Chevy 4.3 is a mini 350

Been watching the channel really enjoy the content Your Very informative . About to purchase a 97x Around Christmas. Would you be willing to do a all wheel delete on my vehicle .

Do you have a picture of how you routed the iacv hoses

Can a piece of tape with a fine line on it rather than soap stone be used?

Hey man question for u

Gonna try this, I just removed the actuator and turned the knob all the way to cold for now lol

need those heater core lines and ac line

Great Video! Do you know if it''s a big deal if the shroud isn't covering the entire core of the radiator? I notice that you do have some radiator core/fin area not covered by the shroud. Does that cause any cooling issues? If you say it's not an issue then I will buy these for my setup! I know I will have some non-covered core as well though with my setup.

Tried one of those cheap pumps and got two defective then got an original denso pump andi regret bot going tjsy route sooner the pump was 105 with the strainer

Did u tune before started it back up?

How well does the baffle work? I want to keep mine awd for the traction, or are there any decent traction mods for converting to 2wd

Could you recommend a forged bottom end for a 07tbss for boost??

Where did you get that white seal?

what a waste of time you guys.....just yak yak yakking....blah blah blah....thank god your not my mechanic.....waste of content..........do you have a day job.....

Talented armpit 😄 jk cool vid thanks for the info. Didnt know there was a tool for that capsule. 🙏☮️

The most important part is attaching the spring to the lid and you just zoomed past that. Just in case you see this, could you slow it down and explain how you did that? At one point you had it on upside down, but you didn't say why you flipped in and why it is supposed to be only one way. If I just put it back on the way it looks like you did it, now the lid won't bend down because something is in the way. Maybe you could explain the purpose of that thin strip of plastic at the bottom of the inside of the lid that kind of goes over the spring. Once I put the 3 screws back in to attach it to the console, that strip of plastic broke off on one side when I tried to bend it. Maybe I just take it totally off.

Ya i had a performance built trans with a stock motor that broke the drum and a stock suburban that stopped moving and i used a different trsns but i checked the pump and it was all fine but i was stealing parts from that trans and kinda forgot i never found the problem but i saw some cracks on the aluminum piece in there and that one the coil springs were shot so i believed the drive shaft did the damage but probably not if its the input drum right

How much of a pain was it getting that bumper off

What brand upper arms?

I watched this before I ordered the tool and did the work. Great job! I followed the mfg instructions and installed the tool then taped around it. Mistake!! Wound up picking aluminum chips out of a freshly rebuilt engine. Due to tape coming undone. So do the tape like he did. It was a really good repair. Simple to do just time consuming. I also ordered the kit just to repair a bad hole. The block I bought to replace mine had been hydro locked. I'm assuming that's the reason the threads were week on the one cylinder and pulled. The sales guy sent me a 10 piece kit it saved me some money. So good video

Nicely done 🎉🎉🎉🎉🎉

I have a procharger kit for 2005 gmc sierra and wanna make fit on my tbss whats needed?

Sounds amazing. What cam and what mufflers ?

Thank you for the detailed instructions!!

So sad.

Man u just solved my problem with this video. Im gonna do that for sure. 👍🏽

Beautiful car except for the 403

Nice Job!

Noticed you also used a harbor freight cherry picker to get it all stabbed back in. I'm installing the engine/trans/harness as a package but the hoist hits the frame before the motor mounts can line up, any tips? Also I'm just using a chain on the ends of each head and hooked them together for my tether

Thanks. This fixed an 05 trailblazer LT. The Woory brand actuator it had started clicking and i could see it move but pop, snap back, move and keep repeating this process. A gear snapped a tooth off and it kept trying to recalibrate but wouldn't, so it kept making noise. Anyway, I had two broken actuators, set the potentiometer at 4300 ohms, set the adjuster at the center lines, and slapped it in. I did the calibration by pulling the hvac fuse, waited a minute, turned the key to "on" and it worked a treat.

IT'S BEEN VERY INFORMATIVE IT HELPED ME BIG TIME

Where is my air injection pump on my 2007 Saab 9-7x 4i I need help it's reading the code p0411 and my air doesn't blow right my truck makes a noise an stay on because of it

Hey, how do i find the value out, mine needs to be zerod out but i cannot find the appropriate resistance value. I have a 2000 buick lesabre so its definitely different

Thanks for telling me about that it won't shoot the fuel until you crank the engine. I didn't ever hear the fuel pump going! My 2000 Rav4 has almost 300K on it. I think it's the fuel pump. I have a crank, no start right now. Thanks for showing all this guys! Wow, 398K!

stripped exhaust manifold bolt and broke it on ls7

Did you have to un bolt them motor mounts and raise it up a bit?

Hey buddy where are you located ??

Grad job

I followed your instructions on setting the correct resistance and voila!

Been cool to see how you did it..

Does the speaker just pry out

How long did it take you to change it out from start to finish? Not counting the brakes you took for recording?

Great videos man, Thank you.

Hi! Thanks for the vids. I have a 2008 saab aero. A couple of issues…and was wondering if you’ve experienced. Leaking oil level sensor. WIS says drop the engine. I’ve seen a few tricky work around using a pick, flashlight and a whole lot of patience! Have you ever replaced the o ring on these. Also, have the smell of gas under the hood. Any common culprits on the 2.8? P.s. how is the doorman expansion tank holding up? Just replaced mine with pro parts Sweden.