7 ай бұрын
8 ай бұрын
Пікірлер
@ilovebeans94 4 күн бұрын
I just broke my whole little lever off the turret adjusting the screw for primer depth nd fml am I upset I really need this set up now or else there's no more priming unless done off press 😵💫
@AndyDep 4 күн бұрын
Sorry to hear that my Etsy shop will have these back in stock soon if you decide to give it a try
@ilovebeans94 4 күн бұрын
@AndyDep definitely count me in I need a few. Thank you sir!
@AndyDep 10 күн бұрын
Yes you get a complete set of parts with each primer assembly so can be installed on 2 presses at same time
@brianmikus6023 10 күн бұрын
Etsy won't let me send you a message for some reason. if I order both primer sizes, does that give me all parts doubled? I have 2 presses that I'm going to set up and would love to not have to change parts each time I want to load a different caliber. one press for large and one for small.
@GrumpyBumpy 22 күн бұрын
My loadmaster carrier was modified by Mike’s Reloading Bench with all his primer feed system mods. Will your system work with my press? My original case feeder works fine if the cases don’t hang up with grit or wrong size cases. What does the top mount case feeder do for the press?
@AndyDep 21 күн бұрын
I am not familiar with Mikes modifications to the loadmaster but if the original lee primer and primer pin still fit in your press then this will most likely work. The top mount case feed is easier to adjust vs original lee and keeps all the cases stationary instead of going up and down with the ram
@GrumpyBumpy 21 күн бұрын
Yes my carrier still works with rhe primer pin and the side mounted primer arm. What sort of adjusting is necessary with your kit to get it dialed in correctly? Also does it come with rhe primer tubes or do I have to buy those elsewhere. I have some primer tubes that fit my Lyman Rock Crusher single stage press.
@AndyDep 21 күн бұрын
@@GrumpyBumpy The kit comes with primer tubes but can use any 5/16 od tubes The main thing that requires set up and adjustment is getting the indexer to work smoothly but this is similar to what you all ready do on loadmaster
@mrsa101 29 күн бұрын
I am very interested in this. i have recently had two carriers break on my where the primer arm attaches. carriers are getting hard to find. I assume with this i could use any of my broken carriers still. I don't know much about 3d printing. has this held up to extended use?
@AndyDep 27 күн бұрын
hi This primer system does not use the original primer arm. Please send a picture of the broken part of carrier to [email protected] and I will let you know if this can work with your carrier.
@georgevaldez1449 2 ай бұрын
This is cool i just ordered this for my loadmaster.
@ForOdin 3 ай бұрын
Just ordered one, I should probably put this in a message on Etsy, but I think it would benefit more people here. I have my Load-Master mounted on a LEE quick plate, would that cause any issue at all?
@AndyDep 3 ай бұрын
The Prime on bottom and my other original tube feed primer system work with the Lee bench plate. I am assuming the bench plate and quick plate are the same thing.
@ForOdin 3 ай бұрын
@@AndyDep just saw that in the manual, honestly, I don’t remember what LEE case their quick change system to tell the truth
@AndyDep 3 ай бұрын
@@ForOdin this is the mount plate that I know it works with. Lee pn 90251
@ohms139 3 ай бұрын
Andy is brilliant with his mods for the Loadmaster. I've purchased two of the case feeder and primer mods for both my Loadmasters. These upgrades saved me from having to switch to the 6 turret press!!
@Kevin_haas_KB1KBT 3 ай бұрын
Just ordered one!!
@wilsonsermanowicz2432 4 ай бұрын
Bom dia Onde comprar ????
@AndyDep 4 ай бұрын
Hi my shop is on Etsy. I only offer downloads for non U.S. customers. This item is not currently available to down load because it is custom order. I am working on how to make this a download option.
@AndyDep 4 ай бұрын
Sorry I gave wrong info. This item is available for download on Etsy for non U.S. customers
@dougp6664 4 ай бұрын
Is the main advantage the ability to quickly change calibers or, does it enhance case feeding in some way?
@AndyDep 4 ай бұрын
This product makes it fast and simple to change between calibers but does not change how the original lee case feed functions. The only enhancement is the addition of a case stabilizer paddle to help prevent cases from falling over.
@dougp6664 4 ай бұрын
@@AndyDep Thanks!
@michaeljacob9614 4 ай бұрын
I just ordered one today 8/29/24.. If this works out I'm going to get 2 more as I have 3 loadmaster's.
@damcollins6393 5 ай бұрын
Do you have a vid with the loadmaster running your products
@AndyDep 5 ай бұрын
Hi, i dont have a full video of running the press with a combo of mods like "top frame case feed and prime on bottom" I can try to add one just showing the system run.
@damcollins6393 5 ай бұрын
@AndyDep thanks for replying, I have two loadmasters and they are the hardest machines to keep running consistent. Anything to make it fully reliable would be a blessing. I would like to see a LM running them.
@joeythefarmer 6 ай бұрын
Wanted to buy this kit from the Etsy store but the website says this product does not ship to South Africa ? Any way you could send it to us ?
@AndyDep 6 ай бұрын
Hi I had shipped international previously but it was difficult to offer warranty support to those customers. Message me thru the Etsy store and we can discuss options. Andy
@joeythefarmer 6 ай бұрын
Etsy shop keeps telling me sending failed on the messaging. Do you perhaps have WhatsApp or Telegram?
@AndyDep 6 ай бұрын
@@joeythefarmer my shop email is shown in the start of the video [email protected]
@faithdepriest2412 6 ай бұрын
Way to go dad!!!
@tashwillafrika3322 6 ай бұрын
Andy thanx for your hard work I would love to get the whole setup you have but I can't order and have delivered to south africa 🇿🇦 is there a way I could buy the files to print my own thank you
@AndyDep 6 ай бұрын
Hi, thank you for the interest. I am undecided on if or when I will offer the files for sale. If you follow my etsy shop you will get updates on new postings when they become available.
@ZuluAltang 2 ай бұрын
Also really interested. Here from 🇿🇦
@AndyDep Ай бұрын
All files are available in n my Etsy shop for the prime on bottom! adepdesigns.etsy.com
@zns9595 7 ай бұрын
Excellent, is the primer sitting depth still adjustable?
@AndyDep 7 ай бұрын
The primer depth is set by feel same way Dillon 550 works. If you force press to full down you could crush or dimple the primer. There is no mechanical adjustment for seating depth.
@tashwillafrika3322 7 ай бұрын
How do i get the primer system and the indexer system please
@AndyDep 7 ай бұрын
The address of Etsy shop is in the video description
@bradyb2233 7 ай бұрын
I just placed an order, but i believe I have a different model of case feed. I have 5 tubes. Can you confirm fitment?
@AndyDep 7 ай бұрын
Hi Brady, this is a direct replacement for the 4 tube feeder PN 90242
@Paul-dc6sp 7 ай бұрын
If I had seen all these updates to this press, I would have updated my Loadmaster instead of buying a Lee Pro Six Pack. Excellent work. Curious how many primers fit in the tube?
@AndyDep 7 ай бұрын
Thanks Paul, the tube will hold 100 primers.
@ronhumphreys9163 7 ай бұрын
How much are they
@AndyDep 7 ай бұрын
Check the etsy link in description. price ranges from $20 to $30 depending on how many you get.
@MrTrollHunter 7 ай бұрын
Wow, now with priming on the bottom you can actually use this press as the five station press it should have been from the start. The way it is set up originally with priming on the top you basically loose one station. Excellent
@bookiefpv 7 ай бұрын
Do yiu sell just the stl?
@AndyDep 7 ай бұрын
Right now only selling the finished product. I may offer the files in the future.
@AndyDep 7 ай бұрын
Hi the digital download is now available in my etsy shop
@bookiefpv 7 ай бұрын
@@AndyDep also the primer feed system?
@AndyDep 7 ай бұрын
Just the top case feeder
@cristianotelles2113 7 ай бұрын
Vcs enviam para o Brasil
@AndyDep 7 ай бұрын
I plan to start shipping to Brazil soon. Just check listings each week
@cristianotelles2113 7 ай бұрын
Where do I buy
@AndyDep 7 ай бұрын
Hi, there is a link to my etsy shop in description
@michaeljacob9614 7 ай бұрын
Awesome! Can you still use the Lee case feed system with this?
@AndyDep 7 ай бұрын
Yes, it works with the original case feed and the new case feeders on my etsy shop
@teeroux 8 ай бұрын
Was looking at it on etsy store. What material are you printing this in? Nylon, PLA exc.
@AndyDep 8 ай бұрын
All printed parts are PLA