the channel is called amateur, but in fact you are very professional sir
@a_woodworker12 күн бұрын
Thank you for kind comment. : )
@StillDontKnowWhatIWantToDo21 күн бұрын
What was the piece you attached to your router before you installed the bit? An extension?
@a_woodworker12 күн бұрын
Yes, It is extension collet.
@dirkmeier28326 күн бұрын
Hand über dem Sägeblatt 😮😮😮
@paulgill4524Ай бұрын
Is your circuit diagram correct? You use a blue wire (negative/neutral) from your machine through the current switch which make sense and you use a red wire (live/positive) from your AC source to your machine. However when it comes to the other side for the dust collector you use a blue wire from your Dust collector AC supply to terminals A1 and 15 and then a red wire from your Dust collector AC supply to your dust collector and a blue wire from your dust collector to terminal 18. Have you got these juxtaposed, colour wise? In your video showing the physical build the left hand side is the same as the circuit diagram where you have used a blue wire for neutral/negative and a brown wire (live/positive) in place of the red wire in your circuit diagram. On the right had side you use brown wires (positive/live) from Dust collector AC source to terminals A1 and 15 and a blue wire (neutral/ negative) from your dust collector back to the AC power source. The wiring from the sensor to the timer relay from K1 and K2 are wired identically in both the circuit diagram and the physical build. My understanding is that for the timer relay A1 is the live/positive side of the coil and A2 is the common/neutral/negative side of the coil. S receives the trigger signal from K2. I am not sure what K2 does or why it is connected to A1. Terminal 15 to16 is a normally closed connection and 15 to 18 is normally open. When your machine is switched on S receives a signal from K1 due to the current flowing from your machine through the current sensor switch and the timer relay coil is energised. This causes 15-16 to open and 15-18 to close thus allowing current to flow from 18 to the dust collector. When your machine is switched off the signal from K2 to S stops, the timer commences its count down and when the count down completes 15-18 is opened and current stops flowing from 18 to the dust collector. Am I correct or have I misunderstood how the system works?
@a_woodworkerАй бұрын
Hello, thanks for watching my video and finding differrence between physical build and circuit diagram. If wiring has correct connecting points, physical build works anyway. But I think color differrence makes viewer so confused. I'm sorry for my mistake. If I keep consistency in building right hand side It's easy to understand. It's not K2 but K1 connected to A1 and K1 supplies AC to current switch. As far as I know your understanding about circuit activation is quiet right. To get more info about switch and relay, please refer to link below. current switch www.aliexpress.com/item/3256805780652162.html?spm=a2g0o.productlist.main.1.6a6446f0E0rl8S&algo_pvid=21da9081-2fe8-444c-acf3-572c44c7ee41&algo_exp_id=21da9081-2fe8-444c-acf3-572c44c7ee41-0&pdp_npi=4%40dis%21KRW%2112371%218660%21%21%219.00%216.30%21%402101364017249975067381019ecdd8%2112000035089547507%21sea%21KR%21702450701%21X&curPageLogUid=6QufHfja5RgZ&utparam-url=scene%3Asearch%7Cquery_from%3A&gatewayAdapt=4itemAdapt delay off relay www.aliexpress.com/item/2251832692033875.html?spm=a2g0o.detail.pcDetailTopMoreOtherSeller.5.78a3TKVVTKVVX9&gps-id=pcDetailTopMoreOtherSeller&scm=1007.40000.327270.0&scm_id=1007.40000.327270.0&scm-url=1007.40000.327270.0&pvid=08a7b598-3e66-4583-8835-ea7e602fe1c0&_t=gps-id%3ApcDetailTopMoreOtherSeller%2Cscm-url%3A1007.40000.327270.0%2Cpvid%3A08a7b598-3e66-4583-8835-ea7e602fe1c0%2Ctpp_buckets%3A668%232846%238114%231999&pdp_npi=4%40dis%21KRW%2113750%2113750%21%21%2110.00%2110.00%21%4021411b6217249968652221750e022c%2110000000454483819%21rec%21KR%21702450701%21X&utparam-url=scene%3ApcDetailTopMoreOtherSeller%7Cquery_from%3A&gatewayAdapt=4itemAdapt
@큰느티-f2jАй бұрын
안전제일입니다 🎉
@a_woodworkerАй бұрын
넵 지당한 말씀입니다. ^^
@큰느티-f2jАй бұрын
장석과피스를 신쭈피스로 했으면합니다.개인적으로 조금 아쉽습니다.멋찐작품입고.후륭합니다.
@FuzzyScaredyCat2 ай бұрын
That part you cut of the top could be converted into a monitor stand.
@a_woodworker2 ай бұрын
That’s exactly what I was thinking. : )
@FuzzyScaredyCat2 ай бұрын
This is a gorgeous pice. Nicely done.
@cady.moriarty2 ай бұрын
I have been scouring KZbin for a simple and thorough video on bowls and trays.... So happy I found yours because it is exactly what I was looking for! Thank you for the subtitles
@a_woodworker2 ай бұрын
Thanks for watching. I hope you make nice wooden tray. : )
@DDRDD2 ай бұрын
정말 중요한 내용이네요 잘 배워갑니다!!
@미소하우징3 ай бұрын
영상 잘 보았습니다. 여기 영상의 클램프도 봐 주시기 바랍니다
@도담도담-u8j4 ай бұрын
안녕하세요! 정말 아마추어가 맞나요? 완벽한 프로인데요^^ 혹시 한국에서 목공생활 하시나요?
@a_woodworker4 ай бұрын
네 쭉 하다가 작년말에 공방을 정리하고 지금은 잠시 쉬는 중입니다. ^^ 좋은 말씀 감사드립니다.
@nelsonw20964 ай бұрын
This is great! I wondered about how to do angled finger joints. Thanks!
@파파뚜러4 ай бұрын
아이구 힘들어 연습 좀 마니 해야겠네 ㅋㅋ
@a_woodworker4 ай бұрын
그렇지요. 아직 멀었습니다. : )
@김동현-v5c2k4 ай бұрын
많은 도움 받고 있습니다. 감사합니다. ^^ 따라만들어 볼 생각에 리머 (1인치-1/2인치, 7도) 구입했는데, 실패했습니다. 영상속 리머가 반짝반짝 좋아보입니다. 가공도 잘되는것 같구요. 이 리머 좌표(?) 부탁드려봅니다. 다른 추천할만 리머도 좋습니다. 좋은하루되세요
@a_woodworker4 ай бұрын
안녕하세요. 뒤늦게 댓글을 보고 답변드립니다. 아마존에서 Allstar Performance ALL11170 1-1/2' Taper 7.15 Degree Taper Reamer with T-Handle 으로 검색하면 되는데 가격이 110$네요. 제가 구매할때는 그정도는 아니었던 것 같은데 올랐나봅니다. 7도 테이퍼를 갖는 훨씬 싼 비슷한 제품들도 보이니 검색해보세요. : )
@염태옥-w2z5 ай бұрын
영상 잘 보고있는 왕초보 목수입니다.사용하시는 합판 종류를 알수 있을까요?
@a_woodworker5 ай бұрын
안녕하세요. 자작합판입니다. ^^
@ryanstroud56655 ай бұрын
The drawer jig for keeping things square is a great idea.
@램프-j2r6 ай бұрын
만들어 볼께요
@syngiroo12216 ай бұрын
내용도 알차고 설명도 참 잘하시네요. 요새 그무개를 살려구 알아보는 중인데 도움이 많이 되었습니다. 가장 중요한 핵심을 잘 짚어서 얘기해주시는거 같아요. 감사합니다!
@marywalter71236 ай бұрын
what size hole is it for the tendon to fit in?
@kinetic.automataworkstatio87876 ай бұрын
👍👍👍멋집니다
@a_woodworker6 ай бұрын
감사합니다. ^^
@tedhodson51186 ай бұрын
Thanks for showing every step in the process, and I like that you watch X-Files while carving the seat :)
@a_woodworker6 ай бұрын
Thanks. I love X-file : )
@krasimirdimitrov50816 ай бұрын
Maaaaan that is working 100% I'm an absolute amateur and managed to pull this off. Mine needs some tidying up but otherwise it's fabulous Thank you
@박도준-x1v6 ай бұрын
주먹장 톱질할때 쓰는 지그는 무엇인가요? 어디서 구할수 있나요?
@a_woodworker6 ай бұрын
안녕하세요. 해당 지그는 '자석 톱 가이드' 또는 'magnetic saw guide'를 키워드로 네이버 등에서 검색하시면 찾으실 수 있습니다. 저는 알리익스프레스에서 주문했었으나 지금은 보이지 않네요. 45도, 90도, 1:6, 1:8 등 4가지 유형이 있으며 제가 사용한 것은 1:8 주먹장용 톱 가이드입니다. 안전하고 즐거운 목공생활 하세요.
@Erosgenuino7 ай бұрын
Enhorabuena, es precioso.
@aceplaybill7 ай бұрын
When you know its a perfect 90* square paper, can't you correct it in the first cut itself?
@md.saifulislam54717 ай бұрын
not good
@stephaniegalvan2728 ай бұрын
Beautiful trays! I appreciate the detailed instructions and the English subtitles.😊
@a_woodworker8 ай бұрын
Thanks for comment : )
@앙정명8 ай бұрын
최고에유!! 덕분에 궁금한 거 다 해결했어요.
@a_woodworker8 ай бұрын
제 영상이 궁금증을 해소하는데 도움이 됐다니 다행입니다. ^^
@Taipan668 ай бұрын
The best full explanation of 5 cut method with the maths on youtube. Once you understand the maths you will never go wrong with calculations. Thank you!
@소남목공방8 ай бұрын
휼릉하네요. 영상 잘보고 있읍니다. 밴드쏘 업체를 알수 있을까요?
@a_woodworker8 ай бұрын
안녕하세요. 답변이 늦어 죄송합니다. 이 영상에서는 2개의 밴드쏘가 사용됐습니다. 03:00 에 보이는 밴드쏘는 14인치 OAV 제품입니다. 03:30 에 보이는 밴드쏘는 18인치 라구나(LAGUNA) 제품입니다. 안전하고 즐거운 목공생활 하시기 바랍니다. : )
@sangyobsong27109 ай бұрын
아마추어는 무슨…. 장비와 실력은 프로 탑티어시네요…
@a_woodworker6 ай бұрын
공방 정리한지 몇개월 됐네요. 이제는 없는 장비지만 상업공방에 사용할만한 장비라서 잘 쓰고 잘 판매하였습니다. 실력은.. 아마추어.. ㅠㅠ 좋은 말씀 감사드립니다.
@부부소소작업실10 ай бұрын
안녕하세요 검색하다가 여기에 계신걸 뵙네요 ^^ 작업과정 멋지게 잘 보았어요 ^^ 전시에 함께 참여한 사람입니다 가끔 놀러 오겠습니다 ~~
@a_woodworker6 ай бұрын
반갑습니다. 제가 전시중에는 자리를 지키지 않아서 어느 작가님이신지 알 수 없으나 이렇게 찾아와 영상 봐주시고 격려해주셔서 감사드립니다. 아쉽게도 공방을 정리하여 향후로 몇년간은 업데이트가 없을 것 같습니다만 언젠가는 또 할 수 있을거라 기대하고 있습니다. ^^ 안전하고 즐거운 목공하세요.
@johnbrooks142210 ай бұрын
Liked The Video Great Work Good Looking Trays
@a_woodworker10 ай бұрын
Thank you : )
@핑크팬티-z6d11 ай бұрын
16:35 와.. 저도 취미로 카펜트리 하는대 딥빡이 여기까지 보이내요
@joshholt287711 ай бұрын
Do you have plans for this?
@a_woodworker11 ай бұрын
I'm sorry I made it without plan.
@MoshiurReza11 ай бұрын
Beautiful project !!
@HobbiemasterAnesloudspeaker11 ай бұрын
❤❤
@WildSBlk11 ай бұрын
Superb
@a_woodworker11 ай бұрын
thanks : )
@Dracoool Жыл бұрын
You did a great job!! Greetings from northern Alberta Canada 👍
@a_woodworker Жыл бұрын
thank you : )
@asiakaztradekazakhstan4 Жыл бұрын
Өте керемет.
@Carpenter_N Жыл бұрын
❤❤❤❤❤ nice
@우뉴늬곤드래밥코다리 Жыл бұрын
9분 40초에 사용하신 측정자 (도구명)이 어떻게 되나요?
@a_woodworker Жыл бұрын
일본 마츠이 사의 케가끼 게이지입니다. 길이별로 여러 모델이 있으며 영상의 제품은 가장 작은 사이즈인 피코 모델입니다.
@우뉴늬곤드래밥코다리 Жыл бұрын
@@a_woodworker 네. 감사합니다.
@retreatc3244 Жыл бұрын
안녕하세요. 인사드립니다. 취미 아마츄어가 아니시라... 프로버금가시네요 앞으로 많이 배워보겠습니다. 감사합니다. 공방구성이 참 좋아보이네요. 기계장비 배치나 작업대 구성에 대해서도 한 번 부탁 드립니다.
@paul.mcguinness6075 Жыл бұрын
Nice Gifts and Hobby woodworking! I would need to make 4 per hour to make a living. So, production methods would need to be incorporated.