Jared Gilbert farms

Пікірлер

@thatoneguy7416 3 ай бұрын

Good ol boys like this is what keeps the world turnin

@twitch_blacky8037 3 ай бұрын

Hey man are you still on KZbin ? I have a question about a 4755. greeting from germany😊

@tannerscott3115 10 ай бұрын

Not gonna lie I’ve adjusted a couple steering boxes an every time it ends in a fast track to oriley.. if u think ur steering is bad just go ahead and replace the gear bc mark my words if u touch that screw your truck will never drive the same again.

@jaredgilbertfarms2067 10 ай бұрын

I've put about 40,000 miles on mine still doing fine

@johnserrano9689 11 ай бұрын

Every single guy wishes deere still made legends like this..hell even my compact 1050 deere responds to turning the fuel up extremely well, and its notoriously way underrated almost all dyno at 44-46hp and deeres infinite knowledge rated them at 37hp lol no idea if the old 1/4 turn equals the old 15hp standard of the fullsized deere (so being a 3 cylinder say 7hp) but we sure do need guys to test this on video. All the old knowledge learned from hard experience CANNOT be lost to time, so we appreciate you making the video

@tyler1671 11 ай бұрын

Stock truck man

@dbz5808 11 ай бұрын

Note that when he says to tighten the allen screw until the slack goes away, he's talking about the slack in the steering wheel, not the allen screw.

@fixnshet5640 Жыл бұрын

When he said “that orda fix it” i knew he was a good ole boy

@el.mas.buscado7221 Жыл бұрын

Dude knows what he's talking about 💯

@SirCavemaninthewest Жыл бұрын

Nice

@805jondoe Жыл бұрын

Thanks

@lee-vq4bh Жыл бұрын

What are you runnin for a turbo?

@jaredgilbertfarms2067 Жыл бұрын

Borg Warner turbo from fair valley performance

@lee-vq4bh Жыл бұрын

@@jaredgilbertfarms2067 what for specs on it? Or what frame of turbo. I'm wantin a borgwarner

@rollincoal7768 Жыл бұрын

What's the danger turning up the hp? I was told if I turned up my 4440 one full turn, don't work it hard. What's the point then?

@cs-gj3yf Жыл бұрын

I’d say 6 turns is to much for field, 2-3 is reasonable

@5er593 2 жыл бұрын

3640?

@jaredgilbertfarms2067 2 жыл бұрын

I'm not sure about those

@5er593 2 жыл бұрын

@@jaredgilbertfarms2067 European models they have 6cly 359cinc JD engine with rotary disel pump.

@losangelos5136 2 жыл бұрын

Loosen or tighten the screw to get more power?

@jaredgilbertfarms2067 2 жыл бұрын

Tighten

@ethanringelberg9771 2 жыл бұрын

How do you do this to a John Deere 2750? Same setup?

@cs-gj3yf 2 жыл бұрын

i would like to know this also, on the smaller rotary pumps

@pineneedles9512 2 жыл бұрын

Guessing I'm late but those carbs on the 620/590 have a hole cut into the main jet to cause the saw to run overly fat at high RPMS, and it only gets worse as the saw breaks in due to the increased vacuum from the rings sealing better, the fix is really easy, just take the diaphragm off, drain and clean it with brake cleaner/carb cleaner and put a dap of JB weld over the hole, let it dry overnight, put it all back together and your saw will lean out properly, just make sure you haven't got it too lean obviously.

@bluemountainfarmer2440 2 жыл бұрын

How much hotter does the motor run after you've turned the fuel up that much

@jaredgilbertfarms2067 2 жыл бұрын

It stays pretty cool as long as you keep the radiator good and clean

@fxture234 2 жыл бұрын

i hope its a well ventilated area!

@jaredgilbertfarms2067 2 жыл бұрын

48" ventilation fan and a 12' door

@fxture234 2 жыл бұрын

@@jaredgilbertfarms2067 Oh good i was worried for yall

@JiCase-tr2kx 2 жыл бұрын

Is that a 9.5mm or 10mm pump?

@jaredgilbertfarms2067 2 жыл бұрын

9.5 I believe

@dionwadefarmsllc 2 жыл бұрын

New subscriber

@jaredgilbertfarms2067 2 жыл бұрын

Thanks

@dionwadefarmsllc 2 жыл бұрын

@@jaredgilbertfarms2067 anytime my friend

@ADN1996 2 жыл бұрын

sounds like shit. that poor saw aint happy

@bigcheese370 2 жыл бұрын

“Why did my engine shit it’s pants”

@jaredgilbertfarms2067 2 жыл бұрын

Must be a IH

@nalley6815 Жыл бұрын

if your tractor blows up from turning up the fuel then it was shit to start with

@zo6rwhp 3 жыл бұрын

Fuck yes porn to my 👂 💪👍🥰

@SlobberDonked 3 жыл бұрын

Fuckin a that was smooth! Washington as well. In the process of selling my lb7. Gonna regret it but ain’t got the extra room after selling my house unfortunately. Lb7 hands down best sounding motor

@tyler1671 11 ай бұрын

Nooo

@georgesrisomsak9650 10 ай бұрын

6.0 powerstroke. I'm biased however. This thing rolls out though!

@brianquigley7336 3 жыл бұрын

Sounds like crap.

@hilmyhanswinata6191 3 жыл бұрын

i love how the starter sound suonded like a someone laughing

@kristinarp526 3 жыл бұрын

Is that a McHale in the states!!!???

@jaredgilbertfarms2067 3 жыл бұрын

Sure is. There's several running over here

@nalley6815 Жыл бұрын

There’s tons of them lol

@JaswantSingh-et9ym 3 жыл бұрын

@parmeetirex4297 3 жыл бұрын

Yaa , we can use same method use in India ,

@mattleonard5268 3 жыл бұрын

Damn that’s a lot of turbo noise

@jaredgilbertfarms2067 3 жыл бұрын

The wc fab intake made all of the difference on the turbo noise

@AverageDemocracyEnjoyer69 3 жыл бұрын

@@jaredgilbertfarms2067 stock turbo otherwise?

@malfunctionjunction6574 3 жыл бұрын

Don’t turn that screw all the way in I found that out the hard way. It’ll kick up to about 4000 RPM and run away

@jaredgilbertfarms2067 3 жыл бұрын

Ouch

@95Thagen 3 жыл бұрын

1/3 of a turn is about 20hp give or take. After 2.5-3 rounds you actually start pulling fuel out of it because the rack isn’t able to get open all the way.

@cs-gj3yf Жыл бұрын

How much is field safe? Tryna turn our 86 and 84 up

@trentdoss1697 Жыл бұрын

@cs-gj3yf on my P pumped 4840 I was told ¼ turn is close to 15 horse. Don't go more than 2 turns.

@henrycomputer1403 3 жыл бұрын

What about the two adjustments right above the plate you removed. I know one is for idle set but don't know which one or what the other does. Also what is proper procedure setting idle? Is there a sequence between the stop on the quadrant and the set screw on the pump? Mine was actually turned up a little to much for me so I cranked it down a little to save on fuel and now it idles to low

@jaredgilbertfarms2067 3 жыл бұрын

Email me and I will send pictures from the service manual [email protected]

@kaddinhinds7398 3 жыл бұрын

Holy shit that thing is quick

@lynnmuncy81 3 жыл бұрын

Big difference over a stock trans I bet. How much did it run you to get it from them?

@jaredgilbertfarms2067 3 жыл бұрын

Yes it is. Around $5200 I think

@xade7863 3 жыл бұрын

Will the pump fill back up with oil After u pull the cover off?

@jaredgilbertfarms2067 3 жыл бұрын

Yes

@MrRenegade800xx 3 жыл бұрын

How far do you twist the pump to adjust timing? Is there any marks?

@jaredgilbertfarms2067 3 жыл бұрын

No marks. Scribe a line on the pump and housing and move about 3/16

@trentdoss1697 Жыл бұрын

@@jaredgilbertfarms2067they like 13 degrees

@MrRenegade800xx 3 жыл бұрын

Love that lope sounds awesome

@cs-gj3yf 3 жыл бұрын

why is it loping? timing?

@jaredgilbertfarms2067 3 жыл бұрын

Rsv governor's could use adjusted I think

@ThatYZguy 3 жыл бұрын

Nice dude!

@jaredgilbertfarms2067 3 жыл бұрын

Thanks. that was a wicked truck when we got done with it

@jaredgilbertfarms2067 3 жыл бұрын

@ Jackson's Rc's and engines! Yes you can use the video. It'd be nice if you could reference me in the description

@ThatYZguy 3 жыл бұрын

This is the video I made and no it’s not a Rick roll! kzbin.infossKv-DnDfso?feature=share

@remcon4369 3 жыл бұрын

Does it work the same for the 6910 ? Nice video by the way

@jaredgilbertfarms2067 3 жыл бұрын

Thanks. Could you send me a picture of the injection pump on the 6910

@remcon4369 3 жыл бұрын

@@jaredgilbertfarms2067 I am not at my work right now , and I cant send a picture in the youtube comment section but maybe you can look it up on Google ?

@jaredgilbertfarms2067 3 жыл бұрын

Looks like a different pump I'm sure it can be turned up but not sure how

@remcon4369 3 жыл бұрын

@@jaredgilbertfarms2067 okay , thanks anyway

@billymcc1020 3 жыл бұрын

I’m a little confused what way did you turn the screw

@jaredgilbertfarms2067 3 жыл бұрын

In for more power. Turn screw to the right

@brianzybura8633 3 жыл бұрын

I just love watching beautiful blasts of petroleum diesel smoke. Thanks for showing.

@jaredgilbertfarms2067 3 жыл бұрын

Thanks. more to come on the tractor making some soot

@straightpipediesel 7 ай бұрын

@@jaredgilbertfarms2067 You still got it? Love the stack!

@noahwheeler4523 3 жыл бұрын

Did you turn it in for more fuel or out?

@jaredgilbertfarms2067 3 жыл бұрын

In is more out is less

@noahwheeler4523 3 жыл бұрын

@@jaredgilbertfarms2067 planning on turning up my 8440 one of these days.

@delta3garcia 3 жыл бұрын

How do you know when to stop turning the Allen wrench? Can you go too much?

@jaredgilbertfarms2067 3 жыл бұрын

On the top of the pump or the back behind the plate?

@bishop5166 3 жыл бұрын

Yes. If you go too much you will fuck up the gears. Some teeth may break during normal wear from turning. I just replaced a steering gear box because of that. It broke teeth and wouldn't turn completely left or right skipping the broken teeth. Think of a bad flywheel with teeth missing.

@StarHunter28 Жыл бұрын

Tighten the stud down until you feel it start to get snug then back off half a turn

@ItsPapiJanciel Жыл бұрын

I can’t reach or should I go underneath the truck?

@Yummypikletits 3 жыл бұрын

So i did the same thing the high and low jet and idle are set right when its warmed up but on cold start i have to flash the choke a bunch till it warms up.

@Yummypikletits 3 жыл бұрын

Its a 2019 cs590 so its new

@kalebgrieve1729 3 жыл бұрын

May need to richen up the low jet more...

@Yummypikletits 3 жыл бұрын

@@kalebgrieve1729 thanks!

@leviberens8638 3 жыл бұрын

What happens Jared Gilbert? It went limp mode

@jaredgilbertfarms2067 3 жыл бұрын

It's a safety in the transmission. When it senses slip it locks in 4th gear and you only have 4th park and reverse until you clear the code

@Train421 3 жыл бұрын

Is your duramax stock and just running the EFI Live?

@jaredgilbertfarms2067 3 жыл бұрын

Yes other than straight pipe

Ең жақсы KZbin

Пікірлер