how to turn the fuel up John Deere 4440

[@brianzybura8633]

I just love watching beautiful blasts of petroleum diesel smoke. Thanks for showing.

[@jaredgilbertfarms2067]

Thanks. more to come on the tractor making some soot

[@straightpipediesel]

@@jaredgilbertfarms2067 You still got it? Love the stack!

[@johnserrano9689]

Every single guy wishes deere still made legends like this..hell even my compact 1050 deere responds to turning the fuel up extremely well, and its notoriously way underrated almost all dyno at 44-46hp and deeres infinite knowledge rated them at 37hp lol no idea if the old 1/4 turn equals the old 15hp standard of the fullsized deere (so being a 3 cylinder say 7hp) but we sure do need guys to test this on video. All the old knowledge learned from hard experience CANNOT be lost to time, so we appreciate you making the video

[@95Thagen]

1/3 of a turn is about 20hp give or take. After 2.5-3 rounds you actually start pulling fuel out of it because the rack isn’t able to get open all the way.

[@cs-gj3yf]

How much is field safe? Tryna turn our 86 and 84 up

[@trentdoss1697]

​@cs-gj3yf on my P pumped 4840 I was told ¼ turn is close to 15 horse. Don't go more than 2 turns.

[@MrRenegade800xx]

Love that lope sounds awesome

[@henrycomputer1403]

What about the two adjustments right above the plate you removed. I know one is for idle set but don't know which one or what the other does. Also what is proper procedure setting idle? Is there a sequence between the stop on the quadrant and the set screw on the pump? Mine was actually turned up a little to much for me so I cranked it down a little to save on fuel and now it idles to low

[@jaredgilbertfarms2067]

Email me and I will send pictures from the service manual [e-mail]

[@billymcc1020]

I’m a little confused what way did you turn the screw

[@jaredgilbertfarms2067]

In for more power. Turn screw to the right

[@losangelos5136]

Loosen or tighten the screw to get more power?

[@jaredgilbertfarms2067]

Tighten

[@MrRenegade800xx]

How far do you twist the pump to adjust timing? Is there any marks?

[@jaredgilbertfarms2067]

No marks. Scribe a line on the pump and housing and move about 3/16

[@trentdoss1697]

​@@jaredgilbertfarms2067they like 13 degrees

[@xade7863]

Will the pump fill back up with oil After u pull the cover off?

[@jaredgilbertfarms2067]

Yes

[@lee-vq4bh]

What are you runnin for a turbo?

[@jaredgilbertfarms2067]

Borg Warner turbo from fair valley performance

[@lee-vq4bh]

@@jaredgilbertfarms2067 what for specs on it? Or what frame of turbo. I'm wantin a borgwarner

[@ethanringelberg9771]

How do you do this to a John Deere 2750? Same setup?

[@cs-gj3yf]

i would like to know this also, on the smaller rotary pumps

[@rollincoal7768]

What's the danger turning up the hp? I was told if I turned up my 4440 one full turn, don't work it hard. What's the point then?

[@cs-gj3yf]

I’d say 6 turns is to much for field, 2-3 is reasonable

[@bluemountainfarmer2440]

How much hotter does the motor run after you've turned the fuel up that much

[@jaredgilbertfarms2067]

It stays pretty cool as long as you keep the radiator good and clean

[@noahwheeler4523]

Did you turn it in for more fuel or out?

[@jaredgilbertfarms2067]

In is more out is less

[@noahwheeler4523]

@@jaredgilbertfarms2067 planning on turning up my 8440 one of these days.

[@JiCase-tr2kx]

Is that a 9.5mm or 10mm pump?

[@jaredgilbertfarms2067]

9.5 I believe

[@dionwadefarmsllc]

New subscriber

[@jaredgilbertfarms2067]

Thanks

[@dionwadefarmsllc]

@@jaredgilbertfarms2067 anytime my friend

[@cs-gj3yf]

why is it loping? timing?

[@jaredgilbertfarms2067]

Rsv governor's could use adjusted I think

[@5er593]

3640?

[@jaredgilbertfarms2067]

I'm not sure about those

[@5er593]

@@jaredgilbertfarms2067 European models they have 6cly 359cinc JD engine with rotary disel pump.

[@bigcheese370]

“Why did my engine shit it’s pants”

[@jaredgilbertfarms2067]

Must be a IH

[@nalley6815]

if your tractor blows up from turning up the fuel then it was shit to start with

[@remcon4369]

Does it work the same for the 6910 ? Nice video by the way

[@jaredgilbertfarms2067]

Thanks. Could you send me a picture of the injection pump on the 6910

[@remcon4369]

@@jaredgilbertfarms2067 I am not at my work right now , and I cant send a picture in the youtube comment section but maybe you can look it up on Google ?

[@jaredgilbertfarms2067]

Looks like a different pump I'm sure it can be turned up but not sure how

[@remcon4369]

@@jaredgilbertfarms2067 okay , thanks anyway

[@malfunctionjunction6574]

Don’t turn that screw all the way in I found that out the hard way. It’ll kick up to about 4000 RPM and run away

[@jaredgilbertfarms2067]

Ouch

[@parmeetirex4297]

Yaa , we can use same method use in India ,