Yeah but how did u get that far?

4 years later and this video helped me. (A father with 4 kids) Thank you so much. You're a gentlemen and a scholar.

That worked. You’re the man!

I have three springs and I have no idea why

Thank you for the video. Unfortunately, it stopped working the second I got it back together. Not sure what's going on.

God bless you man! Worked perfectly. Except I’m not sure how I needed up with an extra piece of hose

Thanks to you I just fixed this in 15 minutes!

Do you know the value from zd1 ?

This video worked perfectly for my hoover spotless!

Thank you for the video. I cleaned some of the filth from the interface board, but the main issue for my F6 F3 error was that the connector to the main board was slightly loose and disconnected. It must have shimmied upward from all the vibrations over the years. I popped that baby back in and put a little liquid electric tape over it to keep it snug.

It worked. Thank you!

This was a big help for me- thank you sir.

Just cleaning the connections on my neighbors washer, first load running right now 🤞🏼 3 years later this video still saving people ALOT of money! You’re a good dude!

What board did you get? Can someone put a link to correct one. Thank you!

This video is great to show you how to disassemble kzbin.info/www/bejne/g4a3nYaGaKyfZ5osi=KHxIRRqZb8eE1jkf and yours does a great job showing how to take apart the motor instead of just replacing it. Thanks!!

Hey there! Just wanted to say thanks for this video, this was the exact I needed! I used my finger and T-shirt as well, so that must be good enough.

8/2023 Worked! I would recommend avoiding the putty method and just take off the entire top cover (multiple videos on how to do this on KZbin), it gives the option to clean any detergent spots and remove built up dust. Also it was way much easy to unhook the screen. Once the solder joints are clean and everything is put back together, reset the error code for reassurance (also how to on KZbin). I've done 3 loads back to back and no issues!

Worked like a charm

I have an easier fix. Just pull the electric plug, then press "Hold To Start" button to discharge the power supply filter capacitor. When the lit display panel finally goes off, wait a few seconds and plug the washer cord back in the outlet. The washer will reset itself and you will be able to use the washer without any error codes. No screwdrivers, no cleaning terminals, no soldering, no expense. This works with most smart devices.

Thank you! It totally worked!

Thanks. That was my issue

Okay, tried the quick fix and I continue to get a F6E2 or 3.. The corrosion is removed and it looks good but doesn't work and I've done a reset and left power off for a while... same issue diagnostics push buttons works and reset works but then power does not. I would think getting a new "Whirlpool WTW8500DC2 Console - Genuine OEM" at $185 would be the right part to get or do I need to get the Control unit at $295? BTW, I did check the cable continuity and it was fine. Thanks, good video!

I know this is an video but I thought I would share my experience in case anyone are having the same issue. I got someone to come and check it. They told me I have to replace the control touch screen panel and I might as well change the control board. He recommended me to buy a new washer. I sat for a couple days thinking what to do. Buy the parts or buy a new washer. I came across this video and read the comments. I did exactly this. Clean the contacts with rubbing alcohol and cute tips. Guess what!!!!!!??? My washer works perfectly fine now. Please take note for these types of models. Do this before buying anything.

p̷r̷o̷m̷o̷s̷m̷ 🤣

Hello, I know you have already had a comment regarding performance in low temperatures, but could you give more input on this? I am in Iowa and will for sure see below zero winter days... How has it performed? Have you needed additional space heaters, or has a fan done well enough to facilitate the heat through the building?

Someone please tell me what size nut driver I need to take the back off? I also can’t get the hoses off

Thanks, had a incompetent repair man quote me $650.00 to replace what turned out to be the wrong board. Between your post and pressing three buttons three times to reset the console I’m back up and running. Great video hats off to you.

Hola ya lo hice y no se resolvió el problema igual y lo solde de nuevo y nada algo mas que pueda hacer?

Thank you so much for this video. It works well !!! (November 21, 2021)

Did the trick! Thanks.

THANK YOU! You just saved me like $400

I also live in Nebraska and am looking at one of these for a shop with water in it. How did this do last winter as it was as cold as I could ever remember. Do you have any other heat source for below zero?

Thank you very much! This worked perfectly and really was not that complicated.

luckily cleaning it was enough. today i am a big fan of youtube.

So what are you paying after installing compared to the very high utility bill you had before?

Those surface mount caps will leak

Thank you so much, saved me a good chunk of change

Thank you so much for your video.....this just saved us from having to pay for someone to come out and service our machine or possibly buy a new washer! I really appreciate you taking the time to inform others! Our washer is working like new again! Thank you again!

Mine just started w/the same error message, I unplugged it for 5-10 minutes, it came back in started working. Was able to finish that load of clothes, then on the next load it did it again, so i unplugged it once again , plugged it back in and now it doesn’t even turn on, no lights, nothing. Any ideas? Is it fixable?? Thanks!

Fujitsu sucks balls. Should have went with Mitsubishi. Wait until something messes up on that, they are a major pain in the ass to work on.

You guys apparently don't read the directions, you have to have a minimum of 16'-20' of linesets, per run, if it's a small room the air temp sensor reads return air of 64° it will shut off, and not operate properly, if you want to cool or heat other rooms with the one head use a fan, but always use the whole lineset of 25', lift unit off ground and coil lineset underneath, don't coil up vertical or will cause oil trap, you guys are amateurs, been installing Fujitsu for 22yrs. Not 1 failure or warranty ever done and all units are still running great. In Arizona, and they get used, installed 3 ton 5 head unit in 1400 square ft. 3 bdrm home with 7"-8" foam insulation at 76° and looking at electric bill of less than $175 per month during June, July, & Aug. Winter only need in morning to take chill off bill in winter will be less than $60, less than a $1000 per yr. we even sleep with window cracked in master 65° set temp at night and 70° 7-9 am then at night a little space heater will keep living rm/kitchen at 73° during the evening before bed so other units don't run much only when needed. Very pleased customer.

Thank you so much, you save me $300 , and my washer is fix.

Hello! After I finished following your demonstration, I succeeded! I thank you! You are so great!

How do you get the top part to release? Putty knife and everything else I slide in there does not work. I break things and I'm about at that amount of pressure. Please give more detail.

Thanks I cleaned the connections 6 months ago and it worked. But the error came back up. This time I follow ur instruction and there it was a filthy connection. Cleaned it with alcohol and boom. It started working again.

Thank you so much. Cleaning the contacts just saved me so much money. So again Thank you for taking your time to save us money.

Man thank you for posting this! It was exactly what was wrong. And get this paid a appliance repair guy to diagnose it and they told me I would have to replace the control board. So I told him I would get back with him. And I went and ordered a control board today just to find this video. Hopefully I can get my money back tomorrow. So you saved me a bunch of money! thank you thank you very much

Thank you so much!!! This fixed my washer right up!!! This saved me so much money!!! Thank you, thank you, thank you!!!

Thank you so much for this. It's videos like these that really make the internet an amazing place. I have a Kenmore Series 700s and after searching for 2 hours, I found your video which showed me how to take the top panel off. Seriously, I LITERALLY couldn't find a video on youtube or anywhere online that mentioned how to take off the top panel. I don't mean to sound demanding but if you could add "Kenmore Series 700s" in the description or something, I think it would really help out others as it seems like these are basically the same exact washer. All the internals seem to match up. Even the service manual, (google search "Tech Sheet - W10607408" to find the official service manual) seems to work with my Kenmore. Thanks again.

Thank you so much!!! I tore apart the washer top and entered the diagnostic mode and found it odd that the buttons still worked with those selections. Looked into ordering a new user interface, $260-350, insane! Searched around for more help and found your video. Used just a plain qtip on the contacts that were visible and wahoooooo, it works! My husband is thrilled I was able to get this done and save money. 3 year old Maytag MVWB765FW with F6 E2 error