I was wondering about your radio and what harness do you use
@koolfredsbimmertech56172 күн бұрын
@@derekgilger6243 That was my clients car I’m not sure. It’s one of those android style radios.
@mdogg32864 күн бұрын
Good video but so much talking at want point do video start fixing the actual issue
@koolfredsbimmertech56172 күн бұрын
@@mdogg3286 I like to explain things for ppl who don’t know much about cars.
@pierrecastanets19746 күн бұрын
What’s that tool you used to remove the oil drain plug?
@koolfredsbimmertech56175 күн бұрын
@@pierrecastanets1974 flexible magnetic drain plug removal tool. Keeps u from getting your hands all nasty!
@koolfredsbimmertech56175 күн бұрын
@@pierrecastanets1974 made from otc
@ronsweet23317 күн бұрын
Great tutorial. Nicely done!
@koolfredsbimmertech56177 күн бұрын
@@ronsweet2331 Thanks!
@RKSAINT9 күн бұрын
How many miles does this particular X3 have? I have a 19 X3 with 71k miles and I’ll be doing this at about 80k. Also did you have to move the transmission cooler out of the way or were you able to get to the lower bolts without removing it? Great video!
@koolfredsbimmertech56179 күн бұрын
@@RKSAINT This one had 90k. The trans cooler has 3 bolts u just loosen them up, trans cooler stays just has to be moved out the way slightly& 1 small coolant hose to disconnect.
@OnTheStreetsWithJM14 күн бұрын
you talk too much and do very little.
@koolfredsbimmertech561714 күн бұрын
@@OnTheStreetsWithJM That’s your opinion. I still fixed a car and got paid.
@eduardocoello190915 күн бұрын
What type of sensor is inside the tank? Do you know the ohm values with okay coolant level?
@koolfredsbimmertech561715 күн бұрын
@@eduardocoello1909 The sensor is integrated in the tank. I don’t know the resistance readings.
@Dort3luk15 күн бұрын
Hey man! I have coolant leaking problem as well. How much is the total cost for oil filter housing?
@adsali0316 күн бұрын
Have you got a video on the oil pump replacement on the G20 m340i?
@koolfredsbimmertech561715 күн бұрын
@@adsali03 No Sir, I’ve only seen 2 techs at my shop do oil pumps on that engine.
@parispate954017 күн бұрын
Where is your shop located at?
@koolfredsbimmertech561716 күн бұрын
@@parispate9540 Atlanta Ga
@ilspeed381723 күн бұрын
Getting ready to do the same thing. Do you know the part number for the yellow o rings?
@juangomez53733 күн бұрын
I’m curious about the same thing, I’ve been looking for these o-rings but haven’t found them.
@Lordapocalypse7328 күн бұрын
Great Video Fred, question for you I'm in the market for a used B58 X5 any years recommendations? thanks in advance
@19nolo8029 күн бұрын
Is this the same process and same part for the 2021 m340 with mild 48v hybrid?
@koolfredsbimmertech561728 күн бұрын
@@19nolo80 The Process is similar the part number is possibly different.
@19nolo8025 күн бұрын
@@koolfredsbimmertech5617 thank you
@eduardocoello1909Ай бұрын
If i use an aftermarket tank, do i have to program something or clear something? I bought one in ebay for less price
@koolfredsbimmertech5617Ай бұрын
@@eduardocoello1909 I’m starting to believe the aftermarket ones have issues with the level sensor. It’s still an occasional problem on the car I worked on. We’re probably going back with a factory one from the dealer.
@eduardocoello190921 күн бұрын
@koolfredsbimmertech5617 thank you, but is it plug and play? Or do i have to clear a code? I have a scanner and do not get any code because of low coolant, only on the dashboard of the bmw.. I changed mine today and still got the wrong reading :/
@koolfredsbimmertech561720 күн бұрын
@@eduardocoello1909 it’s plug and play. The aftermarket and seam to have intermittent issues setting off the low coolant ck message falsely.
@koolfredsbimmertech561720 күн бұрын
@@eduardocoello1909 I recommend going with a factory expansion tank.
@Hybrid255Ай бұрын
Could you show how to flush the coolant in the 2020 BMW X5, and how to bleed the air process.
@highendtrends3508Ай бұрын
Bro this is such a good tutorial, going to purchase through your link now.
@koolfredsbimmertech5617Ай бұрын
@@highendtrends3508 Thx! I don’t have a link but I do have the parts info in the description for this particular vehicle
@highendtrends3508Ай бұрын
@@koolfredsbimmertech5617 thanks so much!
@mydc2200Ай бұрын
When to replace the thrust arm? My x5 has noise when hit the potholes, or bad road condition, last change of thrust arm 10k km ago
@koolfredsbimmertech5617Ай бұрын
@@mydc2200 It sounds like your struts or the strut mounts. The insulators wear out on the strut mounts.
@mydc2200Ай бұрын
@@koolfredsbimmertech5617the strut are boge, is it good brand?
@mydc2200Ай бұрын
@@koolfredsbimmertech5617 i should have installed bilstein, boge made in china, tend to fail early i think
@koolfredsbimmertech5617Ай бұрын
@@mydc2200 Binstin or sachs is good.
@RKSAINTАй бұрын
Where did you drain the coolant from? I have the same car but no one seems to show the coolant being drained or where. Is it the lowest hose on passenger side of the radiator?
@koolfredsbimmertech5617Ай бұрын
@@RKSAINT I just disconnect the lower radiator hose and let it drain.
@kenlovesMuricaАй бұрын
How many miles on the x3 when you performed this repair?
@koolfredsbimmertech5617Ай бұрын
@@kenlovesMurica 90k
@emrahozpolat7199Ай бұрын
Hi, I am stuck for bleed procedure after water pump replacement. Can you help me please?
@RKSAINTАй бұрын
were you able to get it bled? also where did you drain the coolant from before performing the job?
@MrElect0Ай бұрын
Is b46/b48 engine reliable? How does the maintenance compare to the other engines?
@koolfredsbimmertech5617Ай бұрын
@@MrElect0 Yes it is! Just have to inspect it regularly and ck for leaks and fix them.
@OscarCastillo1Ай бұрын
Wow 2022 with 31K and already leaking. Ever have the coolant level indicator pop off and float around in the reservoir? What causes that the pressure? Or a flimsy connection?.
@koolfredsbimmertech5617Ай бұрын
@@OscarCastillo1 This one was leaking from the plastic plug on the bottom of the pump.
@YYoutube17Ай бұрын
Thank you for this video! I literally had this exact same problem on my 2019 X3 a few days ago, wasn't sure what the name of the hose was or even how do this, so this was literally the perfect video for me. Appreciate it!
@koolfredsbimmertech5617Ай бұрын
@@YKZbin17 No Problem!
@RKSAINTАй бұрын
Had the same issue on my 19 X3 at 65k miles after a road trip. I was able to replace it without any issues in my garage. Now my water pump has the slightest leak from the plastic actuated component. Love this car but it is plagued with coolant leak issues!!
@YYoutube17Ай бұрын
@@RKSAINT Wow I discovered mine at 66k miles. So true about the coolant leak issues, I had to replace my upper radiator hose a few months ago as well because it was leaking. I feel like I definitely need to check my water pump as well now because my AC has been acting up
@RKSAINTАй бұрын
Yeah man looks for build up on the black plastic components on the water pump. It’s very minor for me but I got a replacement ordered and a new belt so I’ll swap them out soon
@cuocsonguc3352 ай бұрын
Why u need to replace it thought?
@koolfredsbimmertech56172 ай бұрын
@@cuocsonguc335 it was leaking coolant where the plastic meets the rubber hose around the clamp area.
@ruvemkarpovich2552 ай бұрын
This dude really loves to hear himself talk
@emperorsanders57442 ай бұрын
How did you love the charge pipe without removing airbox?
@koolfredsbimmertech56172 ай бұрын
@@emperorsanders5744 I don’t even remember when you at the dealer and on flat rate sometimes u come up with a short cut. There is a clip on the charge air pipe at the turbo. Once that clip is out u good to go.
@sienna27852 ай бұрын
The most usless video on the internet 😂. Nothing was shown and cherry on the pie - go to professional garage 😅😅😅
@greggodfrey65162 ай бұрын
glad youre back posting again!
@Yaheed_2 ай бұрын
Can the o rings be replace without taking the entire turbo off
@koolfredsbimmertech56172 ай бұрын
@@Yaheed_ yes Once u get the lines loose but it’s only the ones that connect to the turbo. If it’s the turbo line at the block the cat has to come out turbo can stay on on this one.
@Yaheed_2 ай бұрын
@@koolfredsbimmertech5617 thanks bro I appreciate it I was able to get the lines out at the turbo end and I replaced the o ring tighten back up but it’s still leaking from that same line so my ? Is can the line it self be bad and leak even with new o rings
@koolfredsbimmertech56172 ай бұрын
@@Yaheed_ yes is some cases the line leaks between the rubber and the metal pipe. R U working on a N20 or a B46 engine?
@Yaheed_2 ай бұрын
@@koolfredsbimmertech5617 n20 same as the engine in your video
@koolfredsbimmertech56172 ай бұрын
@@Yaheed_ Ok you have the B46 engine. I replace the turbo coolant rerun hose in my latest video. But if the coolant feed line is leaking then the catalytic converter has to come out to replace that one.
@Yaheed_2 ай бұрын
Where are you located bro I have the same leak it dumps all the antifreeze out can drive it at all that how bad it is
@koolfredsbimmertech56172 ай бұрын
@@Yaheed_ In Atlanta
@shawnconnolly65723 ай бұрын
I replaced mine and everything runs fine and doesn't say coolant level is low BUT now it threw code U019F - Lost communication w/ engine coolant pump control. Any thoughts on How to fix this?
@koolfredsbimmertech56172 ай бұрын
@@shawnconnolly6572 never came across that problem. May be a temporary bus communication fault. You can try to disconnect the battery for a few min reconnect and see if it will clear.
@shadiomar41933 ай бұрын
I had the same exact issue on my F30, replaced the tank and connector but unfortunately I still have the coolant error, I noticed that the whole wire is corroded, what does that wire connect to? I think I need to replace the whole wiring for the sensor 😭
@koolfredsbimmertech56173 ай бұрын
@@shadiomar4193 On this on I installed the aftermarket expansion tank. I think that’s the issue because the ck message comes up in the mornings then goes away. So we’re probably going to end up putting in a factory expansion tank from BMW.
@mchaudry98113 ай бұрын
What miles do these fail?
@koolfredsbimmertech56173 ай бұрын
@@mchaudry9811 It depends it can be 35k or 80k for the water pump. Oil filter housing is hit or miss. From what I see the oil filter housing happens over time when there are other coolant leaks. Engine is slightly overheated then melts or deforms the plastic housing.
@bmwlane88343 ай бұрын
You would be a hell of a Dental hygienist! Lol
@bmwlane88343 ай бұрын
Awesome vid brother!!! I'm subscribing!!!
@koolfredsbimmertech56173 ай бұрын
@@bmwlane8834 Thx!
@koolfredsbimmertech56173 ай бұрын
@@bmwlane8834 that’s funny. That’s exactly what it feels like. Like you’re doing a deep cleaning.
@justindanzer76693 ай бұрын
What the fuck bro you skipped the only part we needed. How the fuck did you get the belt off 🤦♂️🤦♂️🤦♂️
@freddyfivefingers13 ай бұрын
Can you please put all those part numbers in the description?
@koolfredsbimmertech56173 ай бұрын
@@freddyfivefingers1 I just added it. But I strongly recommend for everyone to u their vin# and call your local dealer for part numbers because it’s so many versions of the B46/B48 engine. And from year to year you could easily get the wrong part.
@freddyfivefingers13 ай бұрын
@@koolfredsbimmertech5617 awesome thank you, I'll use it this as a reference
@emperorsanders57443 ай бұрын
how much does it cost to replace this in USA through a dealer or Indy. I am trying to figure out should I do it myself vs getting it done.
@koolfredsbimmertech56173 ай бұрын
@@emperorsanders5744 Labor time to replace if the car is out of warranty is around 5.7 hrs. Then you would multiply that times your shops labor rate.
@koolfredsbimmertech56173 ай бұрын
@@emperorsanders5744 Labor rates vary from state to state.
@ChristopherMoore-y1e3 ай бұрын
Honestly man I was looking for one thing but you rambled more about the car than the repair you are a good mechanic but when making content stay on topic brother you bounce around a lot
@morgsigs3 ай бұрын
Hey bro, really helpful video. Planning on doing this on my F22 235i. One problem is I don’t have a plug in reader. would I be able to do the oil change then reset the values at a later date? I hope this makes sense. Again, great video. Cheers bro
@koolfredsbimmertech56173 ай бұрын
Thanks! A simple scan tool that reads live data and works with BMW is all u need. A launch crp 123 or 129x from Amazon will get the job done.
@morgsigs3 ай бұрын
@@koolfredsbimmertech5617 absolute legend, cheers bro. god bless ⭐️
@daltonsteiner32783 ай бұрын
Wow thanks for show us how to do absolutely nothing. I want my 18 minutes back fuck
@Sequel74 ай бұрын
How well would Vaseline hold up ? Would the Vaseline corrode the line because it gets hot?
@koolfredsbimmertech56174 ай бұрын
It holds up good! I normally use sil glide but I did not have any that day. Been using both for years. It helps you so u don’t pinch the o-rings.
@gixxer_squid4 ай бұрын
Quality video!
@cjyungin23234 ай бұрын
new tank came with a sensor and i also bought one before i bought the tank neither of them are reading right
@cjyungin23234 ай бұрын
replaced the tank because the float in the tank was bad but when i put coolant the engine light came on now it’s saying the coolant temperature sensor is reading invalid data
@koolfredsbimmertech56174 ай бұрын
Ck to see if it’s corrosion around the connector.
@cjyungin23234 ай бұрын
@@koolfredsbimmertech5617 can dirty coolant cause it to read bad ?
@cjyungin23234 ай бұрын
@@koolfredsbimmertech5617 the connector looks fine is there a way to calibrate the sensor to make it send the right data
@koolfredsbimmertech56174 ай бұрын
Do you have aftermarket or factory in some cases the aftermarket ones have inaccurate readings.
@koolfredsbimmertech56174 ай бұрын
On the 4 series I had to clear the codes. I did the same thing at 1st. It has an aftermarket one.
@superkong814 ай бұрын
Great Video! Do you have the torque specs for the nuts/bolts?
@koolfredsbimmertech56174 ай бұрын
Unfortunately not of the top of my head. I just get the. Nice & tight with a long handle Ratchet.
@chaicharin4 ай бұрын
Do you think cleaning the dried up coolent on the tank and the sensor would fix the coolent and replacing the radiator cap would do the trick on this repair versus replacing the entire tank?
@koolfredsbimmertech56174 ай бұрын
In many cases the coolant is leaking from the sensor pin where the connector goes. The complete expansion tank has to be replaced in that case.
@northcla24614 ай бұрын
냉각수와 오일 배출이 필요합니까? 냉각수 진공주입기를 사용하지않고 주입하면 문제가 발생할까요?
@ikramzamri4 ай бұрын
Thank u for the great video brother❤
@iMaybeRight5 ай бұрын
I'm give you a like, but bro less talking more fixing. Like talk us through fixing the car that's it. You have alot of additional rambling.