It turned off every time i tried to use my keurig... no coffee

Can you power up an internet modem router?

can I just uninstall chitubox voxeldance does fine for now while I'm beginning. only downloaded because I was having trouble setting up supports.

Lol why are all Raspberry Pi tutorials so strange xD

Disliking the video for the stupid Intro.

My 64GB card still shows a capacity of 7.61 GB in this app. Is it bricked?

I've been wearing Zenni glasses for a few years.. I love them. I need progressive bifocals. I also like transition lenes. I also have an astigmatism. I get a full pair for about $69-90. That's cheap. (progressive, transition, anti glare) I love them. I only had one pair that did not fit well. I had one that broke after a year of wear. The price can not be beat.

Hi ! Sir, Changing the lcd cable will solve the problem of screen horizontal lines ?

Again, this actually helped after like 10 websites that did not

Great Video... I'm completely new to 3D printing. Just got my Bambu Lab A1 mini delivered yesterday. I noticed the small Ironman helmet that you have on your desk. I would love to print one of those for my desk as well. Could you tell me where you got that STL file from and would it be printable on my A1 mini. All of the Ironman masks that I have found are close life size and I have not seen a printable version for the A1 mini as a download file. As I said, I'm completely new to 3D printing and any help would be greatly appreciated.

Thank you

Is the charger positive center or negative center? I lost it and am trying other chargers.

turn your volume down I warn you

Will - great job on all your Vixia videos. You actually address the logical questions that users would confront. These are great little cameras but the interface and operations can be puzzling at times. Regarding the viewer who wanted to use it for streaming…I feed two Vixias into an Atem mini, which is like a little switcher but performs the same basic function as a capture card. I had a hell of a time finding how to get a clean HDMI feed until I came across your video, so anyone interested in streaming should check that out. Also, even though you are not recording on the camera itself YOU STILL NEED TO HAVE A MEMORY CARD IN THE SLOT. if you don’t, the camera will stop sending video after about two minutes and display a generic Canon promotional graphic.

If it's not see through should I sand it first then prime?

Can anyone help me with the firmware which has the change filament option for overnight printing. Even it should have auto leveling as well.

thank you!

It worked 👍

I wonder how the Duramic PLA+ would size up against Esun's Super PLA +?

My guy, when you first swapped colors and zoomed in the camera, the wide angle made it look like you were intently staring off into space in one direction while airbrushing brushing somewhere else. Thanks for the tutorial btw, exactly what I was looking for.

Looks like I had crack on my SD card I didn't notice

Small but mighty!! Got mine last week. I tested it by hooking it to my air purifier. It ran for 5 hours and only lost 1 bar. Still had around 80% battery life.

Where can i buy these connector cables?

This works with CF Cards as well, thanks! The only problem it seems to only reformat to exFAT which some older camera's can read, which then have format again in the camera bringing it back to the problem. Besides that though this does work!

Is this water base acrylic paint? Sorry very new too this

My Same MacBook Pro from 2018 has the same problem

Now you realize how stupid you were when you installed that siding. Vinyl siding is junk!

Thanks, man, perfect, and uh, love the glasses.

you should thin your paint and drop your pressure to 20psi or under

Will it power a tv?

You have to check your areas kWhr rate. Some places hover over 40 cents which makes it around 15 cents per mile. In those areas the only benefit besides quiet ride and tech would be maintenance, as in less maintenance needed. If you have solar and own the system it’s basically next to free. But not many folks own their own solar system.

Fuck WD40......

Changed my bulbs and the one I thought was burned out. It was not turning on. Any other recommendations I can do to diagnose?

Thank you

Great video, was just about to attempt this repair. However I'm not sure I need to, for me the damaged pin on the cable is the one on the far right hand side. I believe its a grounding pin. Do you think it being damaged would matter? It doesn't look burned in anyway. Haven't tried it yet in case it breaks either the display or logic board backlight.

Thanks! 5years later, you bring me back to life!

i dont understand why people Deal with These trash creality printers when everything is set up on Bambus Printers. coming out perfect

What system would I use if I wanted to run pre-made arcade image? Any help would be greatly appreciated

LIFESAVER

Red: your microphone is turned off, or a disconnection error Blue. Alexa is loading, or listening, Cyan blue, means the devices responding Purple, your device has lost connection to the internet, or it's ending not disturb mode White light. Volume or the emergency assist, (guard is no longer available with Amazon alexa.) Orange. your device isn't set up mode, or attempting to connect to the Wi-Fi network, Yellow. You have a new notification, weather alert, or artist you followed. Green. You're in a drop in with somebody, or somebody is calling you. Just say, alexa, answer, or alexa, and more

Dude your video show up out of nowhere after many attempts trying to save my stuck in apple loading issue not knowing this was the real problem, gave it a desperate try and it saved my go to the shop! I can't thank you enough 🙏

Thank you soooo much! Fixed my problem❤

my question is can one hook up the mars so it can print directly from the windows computer instead of this usb stick thing which is so 90's. i mean really? a usb port that wont accept a usb cable? The elegoo neptune prrints perfectly via an ethernet cable so what gives?

Tried it with zigbee2mqtt plug, no reaction, i have sonoff type e stick > plugin but no devices, tried Eufy plugin ... no reaction

hmm, i just bought the image and put it on an old rpi 4, i did until now use Homeassistant but the homebridge plugin does not work very well with Apple Home or Homedash, i have a lot namely zigbee plugins but even the already certified Iqore dit only make on/off switches not measuring on Apple Home. I have a Sonoff E transmitter on my Home assistant, i had flashed it on my Mac to also do Matter and i saw there was a plugin for Sonoff, installed it and put the transmitter on the Raspberry with Hoobs, installed but never paired a device. I think i need additional setup for the plugin? Where to find this?

You don't drill holes, the water is supposed to be slung around the inside of the cage.

Great tutorial. I was looking for those setting because I want to connect an external mic and I need to turn the in-camera volume down to 1 and I couldn't find it. Thanks!

Hi guy I replaced the pcb on my fokoos Odin 5 now it doesn't work well. Some movements don't work well and the ends are all wrong. Is there any kind soul who could help me fix the problems? Thank you very much Bye

Glad to see my iPad is not broken and it’s just iPad os 17 😡😡😡

I was pretty confident that i knew what i needed for painting but this really opened my eyes to what i was missing! This is an amazing video for beginners and im so happy i found this