What is the fault you are actually getting? There is probably a different issue if bypassing the switch didn't fix it.

What is not working on your LG? You can look up the wiring diagram for your machine by searching the model number. Should be able to find the model number on a tag on the door or door opening area.

The buttons were 3D printed.

I could, but then I wouldn't have anything to fix and I'd also not have this content to post.

All the components I selected are designed to run off of 12 volts DC except the twinkling LEDs, which I used a resistor to limit the current. I don't remember the value I used, but that will be dependent on how many LEDs you wind up using. So, basically, everything is wired directly to the 12 v battery pack. Hope this helps.

How tall is your base?

Unfortunately, there are no plans. I built this on the fly including the machining of the head that holds the magnets. I did put together a parts list a while back and will see if I can find it.

(That Tab-Vee shore do look flimsy, tho ... ) 😆🤣😂😅

I don't recall but they were out of an old pile of parts I had. Any power NPN and PNP transistors should work. The ones I used had a different lead arrangement, so I had to get creative with bending the leads around. With that said, check out this article. It gives a few recommendations. :) www.robotroom.com/Big-Trak-3.html

Sorry to hear. What happened specifically?

If I remember right, that assembly just unscrews from the inside under the main board. Normally, the wheel should just pop out with the axle using a flat blade screwdriver. Have never had one completely break before.

@@AlsAutoandAppliance thank you.

Sounds like your battery is bad. Does it give you any beep/red light codes when this happens?

Is it beeping with a continuous red light or blinking red light?

Thank you for commenting! It definitely sounds like a relay is faulty, especially if all other functions seem to work. Good luck with the repair! 😎

@@AlsAutoandAppliance Thank you. I am going to unplug the board cables tomorrow and get it away from the washing machine. hopefully, I can figure out what relay it is. my PCB is different than yours. I'll look in my docs or on the board for a part number. if drawing this in your head looking at it from the front of the washer the PCB is top right in the back. The relays are on the bottom right, there are 8 of them. the cooling vents are in the middle top. If you think the best method is to remove the board, and figure out which one of the 8 is the relay to the pump, I can replace that one and hope it's the end of this rabbit hole.

@@ToddEdmondson most machines have the schematic in a pouch on the back of the machine. Otherwise comment your model number and I’ll see if I can find the drawing. Otherwise you can try to trace the wiring to figure out which relay is the correct one.

I agree 100%, but I am also biased a little since my dad is CCing. 😊

Thank you for watching! Hope you got your eufy going again.

You are very welcome!

Thank you for asking. In addition to the credits, I ask for $5 per video.

Trying! :)

I've always been happy with them. I have them on my other '84 that has MAC high flow cats and dual exhaust. To me, they sound perfecto! Glad you commented and thank you for visiting!

That's awesome! Everything still works on it?

Sure makes for a really long day cleaning up. It's supposed to be a "squeaky clean" and dry environment, lol.

@@AlsAutoandAppliance i agree i dont like the fact water coming though the light while it's on (water and electricity dont mix well) hope yall got it fixed shortly after video ended

Yeah, it's on the ship back as we speak, lol.

I have not, but that sounds like a good idea. Should be easy to pattern and cut with a cricut machine.

If my memory serves me right, you should be able to unscrew the sensor from the back side of the (see video at 28:25 and/or 35:20) and clean it off once you get the main board removed. If it's something you're seeing in your pictures, it could be dust on the lenses or even dead pixels on the sensor. Comment back on what you find and if you successfully get it cleaned up.

Great job and thank you for commenting!

It's been quite a while since I've done this service. If you're 100% sure it's the stuck shutter issue it could be possible. I no longer have spare parts for any other issues. It would be 40 USD. However, I encourage you to try it using my video. :)

@@AlsAutoandAppliance thank you I will follow the video and see what happens

Thank you so much for commenting. Yes, I do prefer working on "old school" electronics but also dabble in surface mount stuff (I think that's why my eyes are so bad now, lol). When you do get your keyboard, and if there are issues, feel free to reach out for troubleshooting help. Good luck!

Congrats on a successful rescue and thank you for sharing your story!

Awesome! Glad to be able to help.

So sorry. The rose has been retired. I'm working on designing a more robust version but don't have a timeline of when I'll be able to complete it. :(

You are very welcome! Thank you so much also for your contribution!

The most common thing that makes the bumper super hard to reinstall is that the upper and lower body halves don't go fully back together due to wires getting pinched. It's really hard to tell, but take a close look all the way around and ensure there are no gaps between the upper and lower halves. Hope this helps and please comment if you get it to work.

So glad to hear! Amazing you found the ball and spring!

Hey DVL! I was NITRO! How the hell are ya? How did you even find this, lol? Been ages since I've air combat simmed. Sure miss it.

Oh my, of course - Hey NAAAAAAHTRO! 😁 How are you?? I’m good! We were squaddies in the |||AirWolves||| then, right? I remember that being a really fun group of guys. Your video was tucked away in one of my old playlists. Brought a big smile 😃 when I saw it again. My sim of choice these days is iRacing. Always have loved a good race. Still gaming when you have a chance?

@@TBolt1 Yep, Airwolves with BASH our leader, lol. Hours upping in a fully gunned B-17 with SNIPER at the controls and decimating everything in the air and ground. Airhead passed away about a year ago from cancer. Beav and I keep in touch on facebook. HERC is the one who was making all the videos. I wish I still had all of them. Yours was a survivor, lol. I do game on occasion. Kids got both me and my wife on fortnite. Do pretty well in that one. Played around on trackmania in steam for a while and get in the occasional team fortress classic. I have one game on my phone called Fun Run 3. It's a run and jump game with 4 to 8 other live players. It's actually the ONLY game on my phone, lol. Working on getting our teenagers prepared for real life is what keeps me occupied in recent times. I've tried installing all versions of air warrior to try and watch all of the gun camera clips I've saved but it crashes when it starts to play. Just wasn't meant to be, I guess. :(

Now that you mention it, I agree with you. Luckily I still have the original panels.

Thank you! Hope you were able to get yours fixed. :)

This is never done. Just one at a time.

You're welcome!

You're welcome!