The big question is, why did the fire sprinkler line burst causing the flood?

end result looks nice

lvp over carpet?

I really appreciate your method. It helped me out a lot.🫵🏼👍🏼🙏🏼😉

20:19 what’s the polarity of the tweeters? I can’t find any information regarding the tweeters.

What head unit do you have to power those speakers? How many RMS?

Great buy and excellent light but common problem is the pull chain breaks. I fixed my exact same Harbor Freight 48” LED Light in under 5 minutes. 1. Take and awl or very small flat head screwdriver and shove it in small square hole on top of light and pry out the black end cap. Once the little tab releases then use a larger flat head screwdriver to pry out end cap completely. 2. Pull out the small chain switch. 3. Cut both black wires as close as you can to switch housing. 4. Connect wires together with a small Marrs type connector and tape securely. 5. Shove connector back into frame and put black end cap back in place, tapping lightly as needed to secure. 6. Plug in light into a switched power bar and you are finished.

Thanks for doing a review of these lights. I literally just added these to my Amazon list before I watched. I thought they looked kinda cool, but watching you disassemble them and test them, I'm going to remove them. They might be good for some uses, but I need great durability and illumination for regular off-road driving.

I’m going to try this with trim around my door frames with years of pain of them they don’t look crisp

Some of the most amazing sunsets I have seen were up there. Thanks for rehashing some old memories. Have a lot of love hate for that place. Over glad I spent several years up there so appreciate the video

My bad this is how no to do a patch job

This is exageres how no to do a patch. lol.

You have a pathetic 759 subscribers and you have your vehicle lettered up asking people to "Like and Subscribe". You are a special kind of... well to keep things clean I'll just reiterate the word I just used "PATHETIC"!

Some of you might attempt following 'other video instructions' of pulling the wires out of the connector without the need to cut or solder. DON't DO IT ! They more often require excess force pulling them out damaging the ends and or where the wire meets. Splice in new wires with new connectors as this video shows 'over top of the harness'. Make them a bit longer. If you're really smart, you won't do either. Remove the wires out of the connector and go 'over top the harness'. Put the square connector ends onto the coil in the correct order. Then push electrical duct putty in. It will secure them and keep the moisture out. The putty can be removed if needed, with a small pic etc. These connectors are another example of Fords better ideas.

Building C or 1435 lost water during the blizzard due the door in question being opened during the storm.

Just a few apartments down from us in 302 lol. I was there for the storm and my wife unfortunately was coming back from Bismarck, she was terrified because there was over half a foot of hail on the interstate.

What about subwoofer and amp install ? Could it connect somehow to factory head unit ?

HOLY CRAP!!! FREAKIN’ LIFE SAVER

Any thoughts on 265/70/16 on Mitsubishi outlander? Please answer me

Very informative video. Thank you. New Subscriber.

Have you had any problems with the tires hitting the strut/spring/suspension assembly while off-roading? I ordered BF KO2 255/55/18 from Costco and they wouldn’t install it because they said it was too close and would void the warranty.

Excellent

Animal

How are they holding up after 2 years?

Guys you don't have to cut the wires, there is an easier way that does not require any cutting. Look up other guides.

I had to run to the store to get a bigger pair of pliers for the wire closure, but otherwise I had mine fixed in probably 5-10 minutes. This was hours ago but I made sure to come back to say thank you very much for a great video on this issue, because it helped me a lot and the last time this happened I paid $300 to have it fixed. Now I fixed it myself for $12 since I didnt have good pliers to put the hose back on lol

thank you sir. last time I paid a guy $265 lmao he did it in 30 seconds

That's not a mitsubishi outlander it's the asx

I came here to change speedometer. This device will do it right? - Will I need to change my tires for this?

Is that A sheet metal screw and washer holding down your coil?

You should see how much mpgs you gain taking off that bumper. I guess you have to install a stock one for it to be a fair test.

Saved yet another happy customer. Thank you!!

That thing sharp

Thank you !

No glue??? What was used to tack it to the wall?? And why didn't U show the process used in the bathroom?

I still have my 2017. Already paid off. Love the mini SUV. I do wanna get bigger tires on it. I use the originals.

Thanks buddy. I thought my pump was shot cause it was making a loud grinding sound and not draining. Turns out it was a piece of clothing caught in the pump propeller. Appreciate it 👍

Wow great job!

Thanks for showing us

I have the same box's and I like it for the price! Thanks for the video.

Depends what the texture looks like on the walls some cases you have to wait 5 minutes almost when it's drying up to take a putty knife & very lightly no pressure on the knife to smooth out the new texture to blend in to look like the older texture.

I have 29” 235/70/16 mud terrain tires on my outlander sport. Stock is 27.7” tires at 225/55/18. I also have a 1.5” ADF spacer and H&R springs 1.2” for a total of 2.7” inch lift. No rubbing at all.

Thank you so much, I’m a 23 dude and its my first apartment lol i was worried i had broken it

Why is our screen upside down ?

THANK YOU

Super helpful! Thank you for posting!

Wow! This was such a help. Cut out all the fat and got straight to the point. You made me the hero of my household in less than 5 min.

Hello! I did all that you suggested but there is no water coming out but i can totally hear water inside the drum… any suggestions on hoy to get to the inside of the drum? Does the top part of the inside of the drum come off? Thanks!

Thank you so much! I have the exact same machine. You saved me a few hundred dollars in repair :)

Why you didn't sanded or flat it with a drywall spatula ?