They designed the oil drain while they must have been drunk

Best detail on linkage I’ve been needing especially power wire placement I needed

Thank you for the video it was very helpful

When taking loose the 24mm head bolt that holds the banjo fitting you may need to hold the nut under the fitting with a wrench.

what rods arte u using i have to use 1/16 6013 e rods

i have a 2008 and the pump is not there

Can’t hear or understand a word you said from 1:43 to the end

Would have been better if u actually showed us what to do....this was useless to me...

Can I get your phone number please

I’m trying to burn some 7018 on mine and breaker keeps popping after 5 seconds

😅

What are you doing on You Tube ? That is the cheapest video ive seen for installing those poly skid shoes, it's a real joke.

_I know it's been a while but is the engine holding up? And how hard was the engine swap?_

Are you retarded

No tiene volumen

Where it is attached to the tractor - is it just welded on? Or does it pivot up and down like a hinge. Can you do a video with closeup pics of the build?

No vale verga tu video

El video ni tiene sonido ni, explica bien como se finaliza la hechura y tampoco muestran como es el traje completo. Lástima. Se aprecia la intención.

Thanks for this video. In addition to the clever trick, it’s the only way I could find out that my flywheel nut was a 32mm. They think there’s so much artificial intelligence out there, but yet nowhere on google does it tell you the briggs and stratton flywheel nut takes a 32mm socket. Even woth a billion of those things sold.

united states bitch

This video should be removed! It's useless and NOISY! \

El vídeo no tiene sonido

Tipaso el primo..

This is exactly what I was looking for something between not using concrete but instead gravel in a controlled perimeter

Que videos imconpletos sin explicar

muchas gracias

The "Banjo Nut" (big hollow sucker holds the pressure hose to the pump) takes a 24mm (preferably 6pt) socket. Also, beware of using anything other than conventional p/s fluid (no stop leak!!!) as anything else can (and most likely will) cause a pressure deviation in the regulator valve that deals with the "proportional steering", and lead to falied seals or possibly the pressure hose itself, due to overpressure. Also, be aware that there are several different pressure hoses used, depending on year and configuration. From what I've seen, it appears that there was a changeup midway thru the 2001 3.3L V6 production line. I was able to source mine from O'Reilly's, but I had to have them pull 3 different #'s before they brought up the correct one. Best thing is to either take a couple of pics & measurements (Banjo Nut to sensor, if w/sensor), or even better, bring the leaker with you. Verify lengths, fitting sizes (and angles), etc while you're able to eyeball everything. Also, don't forget to follow all procedures to flush the old fluid, refill with clean/fresh fluid and properly purge the system of air (cavitation will trap microbubbles). Blessings 🙏🏻🙏🏻🙏🏻

Me puedes decir como cambiar el deposito del antifreez

Did you make that device for your tractor or did you buy it?

Thanks

Note: I tried this and you must make sure that you disconnect the oil pressure tube on the other side of the engine or you will fill the cylinder and crankcase full of gas. The tube on the pump leaves no room for air so it creates a vacuum in the engine. Be careful out there. Not all videos work out they way they were intended.

Gracias por ese homenaje. Orgullosamente nieta de don Eusebio Flores Cruz ♡

Terrible job, teaching!!!

Do you remember what direction the thermostat went in? I installed with the spring in the housing but its keeps leaking? It seems backwards.

No use of reverse? It must be like my ariens with 2 speed reverse Slow and Pretty slow which is annoying. Ain’t nobody got time for that.

Do you remember which model this was? I found one but it is missing the belts

THANKS VERY MUCH!!!!

0:18 how tf do I remove them

I did this and my welder keeps popping over 90 amps I have a 8500 watt generator can you run yours over 100

Liuks👍

Does this engine have a oil filter?

Por favor que medidas de dados usas?

I love how you built all the awesome attachments just to tend to 10 sq. ft. of yard! That's something I would do too, lol. Yeah sure we could probably have done it just as quick with a rake, but that's no fun! Plus then we couldn't show off all of our big boy toys that we built for ourselves!

Chur bro can u just unscrew and put the new one on

Gracias senior!

Thank you for sharing. Keeping this one in my back pocket.

Buen video!

What type of oil goes in it?

Where is the oil filter located?

Hey man, where exactly is the oil filter located? I have the same engine on a poulan pro riding mower and can't find mine for anything.