Your license plate looks like mine no need to explain lol Great vid thanks a lot gonna do this on my Silverado in the spring and this video is a big help Thank you!

Great review thank you

Thanks for the video. I have been looking at thes, and now I'm sold on one

Great job would love to see you build roll cage if you haven't done it yet

Works great 👍👍👍👍

Got the same hook on my car trailer ,don't have to fumble around w a small hook

Tractor supply is getting a lot of RECOVERY GEAR also ,between the two stores you get a lot of choices

Hi, Muddy Beard I have Ford F-350 which jack did recommend to use?

Are you running stock width axles with that set up

i tried 2001 pajero 3,2d automatic offroad. rear locker dont work(compressor no start), no winch, no lift.. but with 255/85-16 toyo open country mt.. im impressed

Well I got scammed I just installed these injectors and my jeep won’t even start now

Does the driveshaft need to be longer?

Can you tig ac with it?

how much pressure can the 4.0 take??

No primer? 4 Years later, how's the paint holding up?

This is great !!!!! I wish I could do it !!!!!

I cant listen to the way you talk. Its like grinding gears

Got some, Thanks!

Great video, thanks. I have a 2013 JKU with 35's. Planning on putting a lunchbox in the rear, and probably a selectable in the front. Likely will do a regear to 4.56 as I drive it onroad quite bit and the occasional offroad when out camping, to get to more remote camping sites. Sounds like it would be a good balance with that setup.

Just make sure POR 15 undercoating / paint underneath everywhere .

What's the bedding process?

How has the HF lights held-up? Are you planning on doing a long term review?

The top side both has the same diameter so forget the more airflow is my thought , thats were the air sucked in .

Because of this video i bought one. Beefed it up with some big ass tires and accessories. It now looks like the batman tank rolling down the street 🤘🏽

Thanks for the comparison

You dont need a 9 in unless your lauching hard an 8.8 will handle roling burnouts and tons of power. Im talking about for cars. Rock crawling is not my education level.

I have the same year jeep. Starting the upgrades I have fund most of the original bolts needed a bit of persuasion.

Man, I was really hoping to see links for all the stuff you put in this video onto your jeep and your description and install it all self promoting your website and your Amazon store that doesn’t have any of that stuff on there like the distributor cap, rotor, spark, plug wires, throttlebody from eBay,all that stuff. What a bummer. I would also love to hear way more about how you figured out that your Bosch fuel injectors were bogus. I also bought Bosch fuel injectors from eBay really cheap and they had the box that said Bosch and everything. But are those bogus? That’s a whole video.

be different get a 6.2 diesel from a gm military truck and run it with the th400. torque is what you need off road anyway not really high rpm hp

thank you. can you please re-link the document or tell us where you got it from?

That looks great! Out of curiosity, what wheels and what size tires did you go with? I have a 4” iro lift and need to replace the stock tires and possibly rims.

GM guy huh? Well can you please explain the mystery of the 4l60E and why sometimes it turns out great and sometimes you get 4 neutrals? :)

Did you test NAPA's brand?

Would this have happened if you were leaf sprung still I’m thinking about putting my wheeling rig on a full c channel frame but my rear bumper would act like a cross member and I’m thinking I’d box in behind spring the mounts and put crossmembers there

You can't leave us hanging like this. post another video. we want to see how far you are!!

So $33 for 4 adapters ..... You have a table for WELDING ....Hmmmmmm . Cut the threaded part off the clamps , get 4 6" 5/8 carriage bolts at $2.50 each , cut the threads off , WELD bolt to clamp... $10 and done . I did this and works like a charm and a tighter fit in the holes without the wobble !!! Have a nice day

X patern maybe on reassembly

Nice job! I'm working on my son's 1988 Dodge D100 and this upgrade is on our list. Is it still working well after three years? Is there anything you would do differently? His truck is a wiring nightmare. The duck foot fused link is bad enough but then a previous owner added some cab lights and a 7 pin trailer light hook up and a trailer brake controller. They made a mess of it. Wires tapped into wires. Shaved insulation and wrapped wires together. If I'm going into this, I'm getting rid of all that crap except maybe the cab lights. I'll find a better way to tie them in. Any advise would be appreciated. Thanks a lot for making this video.

Hi ..what length of links do you have?

I appreciate that you went thru all this for cheap air compressors. But please stop slapping the equipment, it pops pretty significantly with headphones

I purchased a pack of these grease fittings and tried it out on my F250 front ball joints. Was able to get grease in there. Time will tell if it works into the joint.

BEWARE :KingBoss 600 sucks.::::The power surge protection on this product is no good. One over surge on mine shut it down and it will not start up now. Total garbage.

Looking for a link to the pigtail you used

Did it cure the rubbing

Why the KO2 and not a more aggressive tread

Donde se consigue esa suspencion

bro you explained in the video all the smallest details. That was beautiful, and that is what distinguishes you from the rest. Even though I did not speak English well, I understood everything

I have twelve power stations and no problems,one for each appliance or lamp,I have small gas generator for the fridge the total costs $1,500.00 for all equipment. I had five years check and charge one a month. GREAT way TO GO.

Did you ever get this balanced? What was the outcome?

Wish I had seen this video, I am a victim, and they ran like crap.