Beautiful job you're doing buddy. I have been through it myself. It is now 2023 and I'm still flying my typhoon h
@KTHKUHNKK Жыл бұрын
What exactly is cloudsurfing ? Keith
@crazycrow3378 Жыл бұрын
Hi Keith. Been a long time since I heard from you. Cloudsurfing is flying just above cloud level and following the surface of the clouds.
@KTHKUHNKK Жыл бұрын
It looks like you're making videos In 2022 I am still flying my Typhoon H 480 Well I was until a few days ago when I crashed it again. My fault. I am now repairing it again. Keith
@crazycrow3378 Жыл бұрын
I haven’t flown in quite a while. Too busy building a house, but I’m almost done. I’m definately picking it up again this summer.
@KTHKUHNKK Жыл бұрын
I watched your video a long time ago and even after 5 years it's still good. Believe it or not I'm still flying my typhoon h480 in the year 2023 I know what a bugger it is taking those landing gear assemblies apart. I've been through that a couple times. Keith
@cowboys9094 Жыл бұрын
How can I tell if this is what's wrong with mine? Both landing gear won't go up.
@crazycrow3378 Жыл бұрын
Have you turned your copter upside down and tried the gear switch? Maybe you changed a setting on your controller and reassigned the function for your gear switch by accident?
@c-historia Жыл бұрын
well done 🙌 great video
@Loris958 Жыл бұрын
Great, the left esc (blue light) failed I don't know why, I haven't crashed or caught water like you. Anyway I ordered a new main board, I found it on ebay from the USA and now I'm waiting for it to arrive, in the meantime I saw your video which is very useful and very explanatory even if I have one more complication because I also have the INTEL obstacle detection module. Congratulations again for the video. HI
@Loris958 Жыл бұрын
Great, my left esc
@AlfredoAlbanez2 жыл бұрын
Do any of you know the voltage and current of these? in order to test them on my power supply.
@crazycrow33782 жыл бұрын
Sorry for the late response. I wouldn’t know for sure but I expect 5 or 6 volts like any other servo used for landing gear. I can not test this because I no longer have my Typhoon H.
@AlfredoAlbanez2 жыл бұрын
Superb video! thank you! I'll try my landing gear tomorrow
@brubakerjm2 жыл бұрын
How were you able to get the control arm on the servo output shaft? Mine are too short vertically to extend down through the hole in the mounting bracket.
@crazycrow33782 жыл бұрын
Hello Jacob. This is the original design made by Dasaki. Maybe this can help you fix it. www.thingiverse.com/thing:1065755 What I remember from when I made this is that the top bracket had to be fitted directly against the top of the servo to give the output shaft the clearance to reach the servo horn. If its still too short you might want to sand the bracket down a bit and glue it to the top of the servo to keep its strength. Hope this helps. Let me know if you got it working.
@stevendegiorgio31432 жыл бұрын
Waw EPO foam is good stuff.I got an EPO foam plane.(V900)
@ernestopelayo12152 жыл бұрын
Thanks for sharing this info!!, it was very useful for me cuzz im using my TH for the first time.
@dougdowning44203 жыл бұрын
Nice simple design that works every time!
@alexj37093 жыл бұрын
I loved it.... the production is beautiful, piano music perfect!. The long shadows, the approach at speed to encounter the tree at the fork in the path, stark against the setting sun, the incongruous vision of a child playing in the otherwise void and lonely place, the pantomine examined from all sides with a slow circumnavigation, only to swiftly move on down the chosen path, leaving the path not taken.
@crazycrow33783 жыл бұрын
Wow, poetry as a comment. I'm flattered.
@eagleviewhd3 жыл бұрын
I developed an easy way to mount a DR-02 strobe light on a DJI Phantom Drone. Since the GPS for the Phantom is located directly under the center of the drone body I do not think mounting the strobe at this location would be advisable. It needed to be mounted where it would be visible from above. What I came up with was a way to fasten the Ulanzi DR-02 strobe above the battery, but low enough to clear the propellors. I made the mount out of an inexpensive plastic bottle that previously held some hydrogen peroxide (bought at the Dollar Tree for $1.00. I uoloaded a video showing how I made and mounted this on the Phantom Battery: kzbin.info/www/bejne/pJ6rp2aQpNhjo7M
@socshooter3 жыл бұрын
Great Video, helped tremendously when I changed my board. I hope you can answer a question, I need the name of the connector on the ESC LED connection cable. I'm trying to make extension wire longer than the 10 inch OEM cables, however, I cant find the size or name of the connector. Any info would be greatly appreciated.
@crazycrow33783 жыл бұрын
Are you referring to the bullet connectors to the motors? Or towards the nav lights? how about splicing the wire in the misddle and extending it by the length you require.
@socshooter3 жыл бұрын
@@crazycrow3378 Thanks for the message. I was referring to the nav lights. I didn't want to splice the cable just extended, however, I that may be the only option.
@christianfreedom-seeker9343 жыл бұрын
Thanks! Seems quite a bit of Europe is slowly being abandoned
@jasonrobayoguitarrista52923 жыл бұрын
Man, thank you very much. I followed your instructions and the landing gear es working again!!!
@crazycrow33783 жыл бұрын
Glad to be of service
@USMC-Sniper-01373 жыл бұрын
As the ole saying goes, YOU GET WHAT YOU PAY FOR........ I refuse to buy from China!
@crazycrow33783 жыл бұрын
I have bought about a house full of stuff from China and sometimes you get a rotten apple. What I did learn is not to buy from China if you really have to be able to depend on it, safety wise.
@ross94813 жыл бұрын
I found it extremely helpful to take a picture to remember the assembly right after you remove the cover and then print it enlarged. After buying one because of a crash keep the others for spare parts!! Nice video, thanks.
@1979moulay3 жыл бұрын
Very nice
@crazycrow33783 жыл бұрын
appreciate it
@TerrorswellFPV3 жыл бұрын
Hey I want to thank you for this launcher design. I built it in a few hours. Works really well.
@crazycrow33783 жыл бұрын
Thanks man. Glad to help.
@jeffscheule90674 жыл бұрын
Thanks for this video!
@brunoitey8224 жыл бұрын
Thanks, well done! Following your tutorial, I took one apart an noticed that the screw of the mechanism is bent due to a "hard landing".... Would you know where to order a new one?
@crazycrow33784 жыл бұрын
I wouldn’t know where to find one right now but I do have some part numbers that might help your search. The bracket that holds the leg is YUNTYH131 and the complete motor assembly is YUNTYH109SVC. I have never seen the screw sold seperately. If you’re handy with a lathe you might be able to machine a new one from a bolt or piece of threaded rod. Good luck on your search and if you have any more questions feel free to ask.
@flymenno1234 жыл бұрын
Hey hallo, goed gemaakt man. Zou zoiets ook kunnen werken voor grotere zwevers? Wellicht de ‘glijbaan’ wat langer maken, zwever heeft een spanw van 3,75m en wil ook gewoon in weiland kunnen starten met hoog gras, heeft een klapprop in de neus. Als je ideeen hebt hoor ik t graag, grt Menno, Almere
@crazycrow33784 жыл бұрын
Ja dat moet vast lukken. Als je 3,75 breed bent heb je bij lage snelheid al aardig veel lift dus een veel langere glijbaan zou je denk ik niet nodig hebben. Als je de elastiek strak genoeg spant kun je al veel power uit de eerste paar meter halen. Ik weet niet hoe groot je prop is maar let wel op dat je pas gas geeft als je genoeg lift hebt gegenereerd. Anders kan de prop je elastiek grijpen met alle gevolgen van dien. Een andere optie is de elastiek in een V vorm spannen met 2 grond ankers op een meter of 5 uit elkaar, dan kun je na een meter of 3 al gas geven zonder bovenstaand risico. Bij een pusher (zoals mijn X6) heb je hier natuurlijk geen last van.
@flymenno1234 жыл бұрын
@@crazycrow3378 hey kerel, bedankt voor je reactie man.. ja dat van die prop snap ik.. zit een aardige op.. 17-11 zo ff uit mijn hoofd.. Discus 2a van Topmodel.. nu doe ik handstarten.. maar is al een keer mis gegaan.. semi schaal modellen zijn kritisch in de start.. iets te soft uit de hand en je overtrekt t spul zo.. met een klap als gevolg.. dus daarom dacht ik of met een startwagen.. maar dan heb je weer kort gemaaid gras nodig.. of iets van een bungee-schansje of zo... zal er eens over nadenken.... hij weegt rond de 4,5 kilo.. dus wel even wat snelheid nodig om mooi vlak weg te starten...
@razakmeshouni86114 жыл бұрын
Wauw beautiful. great job! ik wist niet dat mn eigen land zulke juweeltjes had. Binnenkort maar op kasteeltour door Brabant!
@laoraarkeman54334 жыл бұрын
nice video. brabant, the land of my ancestor. best regards from jakarta, indonesia.
@Durango2144 жыл бұрын
How do ypu remove the arm hooks?? Pls
@crazycrow33784 жыл бұрын
On the frame they are attached with 2 screws from the bottom of the clip. And on the arm it’s just 1 screw that can be loosened through the hole just above the “press” marking on the arm. After removing the screw you can lift up the tab that holds the clip in place. Use a thin screwdriver and go in through the slot on the side just below the “Press” marking. You can see the metal tab that holds the clip in place. Just flip it up using the screwdriver and then pull out the clip. Hope that helps.
@KTHKUHNKK4 жыл бұрын
You are an expert brother. I wish I could solder like that.I have a pair of headphones that I'm going to attempt to put another Jack on. Actually I'm looking for somebody to do it.
@crazycrow33784 жыл бұрын
Good soldering is not an art. It just takes practice and a good iron with the correct tip for the job. but the most important thing in my opinion is flux. Never start without it. I found the best flux is the stuff you buy at the hardware store to solder copper water pipes. Ask for S-39 soldering flux.
@heronimusb.46564 жыл бұрын
Do you have them also in different colors?
@crazycrow33784 жыл бұрын
Yes they also make pink. Which everybody knows is your favorite color. 😂😂💝
@InspectordeBilleteras124 жыл бұрын
Awesome video bro! I replace the mainboard but the problem persist. When i push the power button it only does one BEEP and turn 3 times the five leds.
@crazycrow33784 жыл бұрын
That’s strange. By 5 leds do you mean the nav leds on the motors? There should be 6. Have you tried rebinding it to the st-16? You can also check the yuneec pilots forum. There’s heaps of information there on the Typhoon H.
@InspectordeBilleteras124 жыл бұрын
@@crazycrow3378 the leds from the mainboard! The drone dont turn on. I checked the forum but I didn't found an specific solution. :(
@crazycrow33784 жыл бұрын
Gogo Touris There should be 6 led’s to my knowledge. They indicate that the ESC’s are working.
@InspectordeBilleteras124 жыл бұрын
@@crazycrow3378 checked, the six leds flash 3 times and sounds one beep, but the drone don't power on
@Theoregoncoastexplored5 жыл бұрын
Got home from flying and noticed a landing leg loose. I thought i broke it but i only catch so never once landed on ground. So was confused til you showed you can flip upside down and let gear fold out. Fixed the issue so thanks for video.
@crazycrow33785 жыл бұрын
My pleasure, glad to help.
@WereJoebin5 жыл бұрын
perfect this is just what i need
@ajmedia12745 жыл бұрын
I too get that horrendous lens distortion causing the curved horizon. I use pp cc to correct in post anyone know any other way?
@GarageMahalLife5 жыл бұрын
Need to solder any connections, this will help Soldering wires, bullet plugs and the Yuneec Tyhpoon Drone Repair (link: kzbin.info/www/bejne/oJnCg6x9j76Xhrs) kzbin.info/www/bejne/oJnCg6x9j76Xhrs
@ssureshot5 жыл бұрын
It's called a "B roll". Mine was a bit longer: kzbin.info/www/bejne/a3nZmnxvZ9elfpo
@crazycrow33785 жыл бұрын
Bill Branning Cool. I’ll check it out when I get home.
@ssureshot5 жыл бұрын
What has your long term experience been with the Maytech carbon fiber props?
@crazycrow33785 жыл бұрын
Bill Branning I’m still using the first pair and never had any problem with them. They are much more silent than the originals. They provide more stability in higher wind conditions because they hardly flex, so thrust is much more acurate. And most important is they saved my drone several times flying in wooded areas. They cut through small twigs where the originals would have snapped.
@crazycrow33783 жыл бұрын
Fiy. Still flyin that first pair one year later.
@USMC-Sniper-01373 жыл бұрын
@@crazycrow3378 Just pipe up and let us know again in another year as like an anniversary LOL.....
@crazycrow3378 Жыл бұрын
@@USMC-Sniper-0137 sold my H (dumb mistake) but the guy who bought it still flies with em.
@ssureshot5 жыл бұрын
THAT's what a DIY video should be. Thank you...
@crazycrow33785 жыл бұрын
Thanks. Glad to help
@Jackins19565 жыл бұрын
Thumbs Up & Lots of help. Thxs.
@reece_golfs5 жыл бұрын
Holy cow, Crazy Cow! This is crazy good footage! ;-) great work! Just wondering if I can use it on Instagram and attribute your name or company in the post? Thanks :-)
@crazycrow33785 жыл бұрын
Thanks man. Go right ahead. It would be my honor 😉. Oh and by the way, I’ve never heard a crow go MOOOOOOOH 😝
@reece_golfs5 жыл бұрын
@@crazycrow3378 haha! Do you have an IG account that I can tag when using the video? Do you mind if I use clips from it on more than one occasion? I will of course tag you and credit you anytime it's used!
@DemiFlower10105 жыл бұрын
Hi great video, can you tell me where you got the orange plug housing from?
@crazycrow33785 жыл бұрын
They are 3d printed. I downloaded them from thingiverse.
@seanward5 жыл бұрын
A great video. I am only just getting confident with a typhoon H that I got when it was brand new, that crashed the first time I had it out, then sat in the box with nowhere to fix it for a year and a half. I got a Segway Loomo that I can’t wait to ride on with this drone following me
@crazycrow33785 жыл бұрын
Thanks. Before attempting to use follow mode make sure you are totally confident in flying the H in all flght modes. Smart mode is supposed to make flying easy but on the move it makes it much more difficult, make sure you fully understand what the craft will do. things like the "smart circle" can really ruin your day when you don't understand them properly. study the manual on the Yuneec pilots forum before your next flight. It can only make your next experience with the H better. Happy flying buddy!
@KTHKUHNKK4 жыл бұрын
@@crazycrow3378 I just subscribed I have a question I am curious about realsense what position do you put the switches in to make it work properly and will it climb to avoid objects thank you
@theexodus2845 жыл бұрын
wow how u added differential thrust?
@crazycrow33785 жыл бұрын
Choose 2 different channels for your esc’s and program them into your rudder channel. You can find many videos on youtube on how to do this.