Where in Ky I am in the Hardin co area

Film this in australia, a whole bunch of different scenarios could come into play, . 1. Cop a fine for no life jacket. 2 cop a fine for no safety kill switch lanyard 3 the censorship board could fined you for publishing unsafe acts, 4 get punched out a the boat ramp for being a Richard 5 defect notice on the trailer(no guards), 6 the health department knock on your door and take you away for being crazy, but you can’t see it because of culture discrimination- your crazy, go back to obscurity.

Just a thought you could get it galvanised hot dipped and you could either paint or not after that

Satin dulls more with time.

Awesome... Thanks

Keep up the good work

Super impressive, very inspiring!

My daily driver was a '67 sedan, back in the day. Only problem I had with it was it got stuck in 4th one day, fixed that by disassembling the trans and cutting a deeper groove for the shift dog snap ring. The rings in the 1300 were chrome, I wound up installing cast iron for a good seal, it still had the hone marks in perfect condition.

Can u tell me whats the best place or where ugot ur parts

Tks! For Talkin bout priming by filling filter, lol. Rarely rarely does utuber say or do that..Im 66yo, Been shade treeing for 50 years, Jus got a 05 Dodge durango,. Im yelling at the other utubers, " "Prime the Damn Filter", lol. Tks !

we have been using it for more than twenty years, cut in half with water.

Junk yard horn off almost anything $5.00

I highly recommend Subaru horns as a replacement.

Great video! :) I once managed to repair the horn on my Volvo 850 by hitting it with a hammer - dislodged a bunch of rust that fell out and the horn started working again :D

Thanks Man 👍

Interesting. Have your seen the KZbin advertisements for a spray on rust remover that is non-toxic. Supposedly, you can handle it with no gloves.

Nice to see you back 👍

That's a loud horn for a little truck 🚚

Nice work on the rebuild. I was surprised mine work also. The truck did arrive with 2 spares. I did have to rebuild the mount someone smashed for AC clearance. Did not know the 520 had 1 on each side.

He's back!

welcome back

👍👍👍

Lots going on at that shop. Nice truck

Beep beep, good video Benny!!

Well that blows... Great seeing you again.

how many hours did it take you?

You're videos are GREAT to watch. I'm the original owner of 1976 CB-360T. I've done all this stuff on my bike (I've now changed to an electronic ignition). I have had the engine completely apart several times, but it was a long and hard learning experience. I also have a spare motor which I bought off of e-bay for $400. The spare is what is in the bike now. I've gotten to the point where I can swap out the motors in about 4-hours. 😄

I wish mine had a headlight and speedo.

I'm looking for the hood and the two fenders for one of those same trucks

I'm looking for the hood and the two fenders for one of those same trucks

I'm looking for the hood and the two fenders for one of those same trucks

Wow now that's a parts washer

With what would you treat the whole underchais of the car ,? It's so rusty and I need to buy the rust remover and converter,,can you reference some brands

Needle gun is such an underrated tool

30mph

which propeller you have... I think 17 pitch

Where did you get the vinyl

Helmet but no pfd! Safety! Not so much!

Jim Ohanahan of Brunswick Kansas high school had one off those in 1975. He was going down Tank road north of the tank farm and according to his twin brother Neil he hit 102 mph. It was knee and he a tailwind of Kansas and was taken back to the old days since he was a crazy loony boy and once eight forty donuts

How much?

Top tip, if you touch one of these 545re trans, you must go into your scanner and reprogram the TCM, and set it back to factory specs! That way the TCM will relearn your driving habits and all is well with the world.

Actually, the spin on is for the tourque converter filter to keep dirt out of the lockup mechanism, just like the famous Allison transmission👍👍 and, if you change the fluid ( ATF +4) and filters at 30k, these transmissions are just as reliable as the Allison. But hardly anyone ever changes this stuff on time, that's why dodge transmissions have a bad reputation. They're not 727A or 907 transmissions! These are high tech solenoid and computer controlled transmissions, the most advanced slushboxes of their time. If you treat them good, they'll treat you better. The end.

Will you make me a set for my IH 504??

Looks as bodgy as SAD Chad

Hi, great job. For what is the ball at Minute 4? Do I need it at my ke125, too?

Amazing work. I am still trying to get my reverse lights working. I read its the lowest switch the one with white wires. My 70 has 3 switchs. Neutral, 4th and reverse. My reverse switch has no continuity when pressed. The other switches do.

Hopefully there’s oil in crankcase

Why would that be in dumpster

Seats turned out good.

If you can turn around, check your speed on your phone, you're not going fast enough to necessitate a helmet