What is the reason to posted this completely unless video?
@slavsl17063 ай бұрын
At the end of the video (11:30) after you remove front panel. There is a some grey valve with spring. In my case looks like that there is not enough pressure (after knock sometimes work) and water instead goes by nozzle going straight to drain canal. Valve looks ok for me, spring move freely after push from inside. Would you think it will be a main pump starts failure ? Did you had such a case ? No any errors show on display. Any advice welcome :) Thank you
@coffeetechph3 ай бұрын
You should check the solenoid valve. Try to check every components where water comes by.
@slavsl17063 ай бұрын
True. Best Video ! Thanks
@zivotaspasojevic27654 ай бұрын
Hello one question i have sane Jura z6.Does the grinder have 3 springs and balls inside below small blade or not?Cause u can't squeeze the grinder enough.Whatever i doo it moves and grinding isn't fine enough.
@coffeetechph3 ай бұрын
The new version grinder of jura are not having spring and balls. They fit the lower burr on the plastic part, that's why it look like stuck on it.
@bozo41365 ай бұрын
Hey Copi! Is it recommended to to this service (clean the brew unit) before any problems occur? I purchased a used Jura Z6 from a company auction. It has over 12000 cups made and I dont know its service history if any. It is working great! But im a maintenence kinda guy. Should I try this even if it is working good? Maybe there are more parts in the machine that could use cleaning, or any orings that should be replaced? How often does jura recommend making this service?
@coffeetechph4 ай бұрын
It's better to clean and re grease, every 6 months. Also check the condition of every oring, you can replaced oring every year.
@mickatlas32725 ай бұрын
Thanks for the video used Part 1 & part 2 to pull apart my wife's Z6 cleaned the Brew head it was fairly easy to follow your video, all I did was play it backward when parts came in to put it back to together you saved us a ton of money because of this video
@sashayoung45177 ай бұрын
Where can i buy the screwdriver for those 6 divot screws?
@coffeetechph3 ай бұрын
Jura - parts . Com
@kef1037 ай бұрын
Wow, your method of doing absolutely nothing was no help.
@absorb217 ай бұрын
would love to see which screw goes where..
@coffeetechph3 ай бұрын
What screw?
@josephkingston25267 ай бұрын
Thats what I call an expensive crap.
@johnf36688 ай бұрын
great work! is that a torx screwdriver to remove the panels? thanks!
@coffeetechph8 ай бұрын
Yes. And special tools called oval bit.
@johnf36688 ай бұрын
Ok thanks so much. Someday I’ll want to open my beautiful new z10.
@nickhaining45239 ай бұрын
The best Eletta Plus strip down video ever. Searched for ages and luckily found this. Absolutely brilliant. Thankyou very much.
@sucka2319 ай бұрын
Did they update the design and hose size? I have had a number of giga 10s which keep getting a system fill error message. I am using grind setting fine or medium. Fine seems to always cause error message.
@coffeetechph9 ай бұрын
You should check the membrane thing. This is a part after the water pump. The membrane is a one way valve, to check the parts you need to blow from output to input, if the wind comes out from the output to input, your membrane is need to replace.
@right..565110 ай бұрын
Been asking around since like 25th of sep if i should by the breville barista express, no seems to care lol. The sale is only active until today 1st Oct. Hopeful that you will give me an answer since the upload is new. Where I'm from the breville barista express is on sale for 540 USD, is this a good price? Is it maybe even considered to be a must buy or do you think I can get a better price further down the road, like Xmas and so forth. Thank :)
@coffeetechph10 ай бұрын
If it's brandnew. It's a good price. Sorry for the late reply, kinda busy. Hehe
@right..565110 ай бұрын
@@coffeetechphNo worries 😊 couple of other people answered on that day. It was a good price but I decided to wait until black Friday and prime day sales start to see if I can get an even better deal. Maybe combine a baratza encore esp with a breville bambino instead? Who knows ? Let's wait and see! Anyways appreciate the reply, have a great day my friend 😊
@paulus429410 ай бұрын
Beautiful Z1O! I'm looking forward to the next black friday to offer it to me.
@billallen454911 ай бұрын
I just purchased a Jura Z10 Signature for half price while on vacation in Germany, image my dismay when I couldn't even get past the startup menu after spending 3 hours running a 240V wire to my kitchen counter. "Drip Tray Not Fitted" message. Rather than chase a complicated shipping & warranty repair I decided to take a look inside ... with your video I had Z10 stripped naked in less than 5 minutes. Found the problem right away, one of the door micro switches (see orange wires front bottom) had popped loose in shipping, snapped it back down (no tools) and the message went away. Finished the setup menu and my Z10 works perfectly. Your video gave me the confidence to lift the hood and find the problem. Thank you very much! Vielen Dank
@billallen454910 ай бұрын
Well one month later and the same message "Drip Tray Not Fitted" returned. Had the side panel open in 2 minutes as I never put back the 2 oval tamper resistant screws. Yup, same inboard micro -witch was popped up again. Upon closer investigation found 2 tiny plastic pieces in the bottom of the unit, these are retainer clips that are meant to hold the micro-switches in place. They must have broke off during shipment, no doubt from an impact drop. Sure enough the shipping box bears the mark on the front right corner. Clever solution ... foam earplugs, rolled them up and placed one above each micro-switch, foam expands and holds the switches solidly in place.
@_SXPHII_11 ай бұрын
Hi What part did you use
@coffeetechph11 ай бұрын
I replaced membrane, it is one way valve that connected on the water pump.
@neo8108 Жыл бұрын
Next time use Phone for recording not a Toaster.
@coffeetechph10 ай бұрын
Hahaha i'm sorry.
@user-ls9iv2zz7v Жыл бұрын
Thank you very much for the informative video. I have called Jura U.S., 4 times to try to have my z6 serviced but all I can do is leave a message and then they call back either 4,6, or more hours later when I can’t take the call, so that leaves me no choice but to repair this machine myself . Your video will allow me to attempt my own repair. I can only find part 2 of your video, is part 1 available? Thanks again!
@robertwest678 Жыл бұрын
Thanks so much fantastic break down
@willo7979 Жыл бұрын
By the way; Anybody knows how to get it skips the need to press knob upon every power up? How i wished it rinses automatically without the need to press knob manually.
@coffeetechph10 ай бұрын
Auto rinse you mean?
@willo797910 ай бұрын
@@coffeetechph yes
@willo7979 Жыл бұрын
Guess it’s time for brew group deep cleaning?
@gtg242v Жыл бұрын
Which screw driver should be used to loosen the round head screw in the front and back?
@coffeetechph10 ай бұрын
It's called oval bit.
@ceesbrooms4176 Жыл бұрын
It is a pitty you don’t have sound
@Progenitura Жыл бұрын
I'm wondering if there is a way to remove only the pre-grounded coffee pipe without having to take out everything. In the video it seems it's one of the few things that didn't come off. That thing is a mess. So much mold and dirt. I need to clean that thoroughly. Also, maybe the funnel attached to the grinder? I see that it's basically made of two pieces. One came off in the video, but the other one seem stuck to the grinder and you only took it off after the grinder came off. Can that be removed without taking out the entire grinder? Thank you!
@ChasVS391 Жыл бұрын
Useless
@Quassi30 Жыл бұрын
Hi. I cannot take down side plastic... in back I no have normal scew// :(
@coffeetechph Жыл бұрын
you need to slide it up to remove. just use any flat type thing
@robert1340 Жыл бұрын
I think you forgot to turn on your mic.
@robert1340 Жыл бұрын
You forgot to turn on your mic.
@donbrunnett5427 Жыл бұрын
Thank you so much for the very informative video on my Jura ENA 9. I have a jammed grinder motor (I am assuming it should rotate once the outer burr is removed but it won't rotate at all). I wonder which steps are required to remove the motor assembly. I have already removed the sides and top. Thank you so much for any assistance/advice.
@artstudio-i514 Жыл бұрын
Thanks Bro. Wonder if you know how to fix the LCD display screen. At the some point, it was slowly gone and didn’t appear even through other buttons next the display screen all works.
@WEGOT30SUBGUYS Жыл бұрын
Does anyone know what is the MOSFet used for this Z6? It's located at Q49. Mine blew off.
@WEGOT30SUBGUYS Жыл бұрын
I have this Z6, but the Mosfet located on the PCB, Q49, has blown off. Now the machine won't power in. Does anyone know what the Mosfet label is?
@barneyauton78102 жыл бұрын
This would help if the video was of better quality. Very good information that could be beneficial if it were in frame.
@elainedunham2 жыл бұрын
I keep getting an error that says to fill the bean container but it is full. I tried to take apart the machine but the round bolts are stoping me in the back, is there another way to remove it? Have you ever had this problem?
@coffeetechph2 жыл бұрын
You need oval bit or oval screw driver. I don't think if the long nose can make it.
@carlosalbertoalonsobarrien7712 жыл бұрын
Que desarmado ocupas para quitar los tornillos de la tapa que venia escondido
@francescodonati33022 жыл бұрын
...thank you....you are my hero of the day....it looks easy but if you don´t know it has to be, you´re lost....so thanks a lot....
@coffeetechph2 жыл бұрын
Your welcome sir! :)
@medoking75012 жыл бұрын
bravo, good job I disassembled mine, so the video helped me put it together
@adimanole2 жыл бұрын
FOR z6 part 1??
@coffeetricksandtips10182 жыл бұрын
So perfect and usefull 👌🏼
@mguerramd2 жыл бұрын
Very much a risk to do it in the sink! You can drop small parts down the drain. Do the disassembly and reassembly on a work bench on a towel that will grab the small parts you drop inadvertently. Check this out: kzbin.info/www/bejne/mmmwm3l7jdyMaLs
@Sam..............2 жыл бұрын
i WAS THINKING THE SAME THING....
@rickzemen14424 ай бұрын
if the video to check is out there, please find and post new link, that one is gone
if you are installing new burrs, the plastic collar goes on after the lower and upper supports are re-connected. Otherwise, you can't reconnect them. This hung us up for 1/2 hr until we figured it out.
@mdkamruzzaman91982 жыл бұрын
Wow nice
@Nealf20022 жыл бұрын
Hi I tried to follow and removed my Ena 9 Brew group and now cannot remember the correct position to put it back in. I put in back and while rewinding after the power is on, it get stuck near the top of the spooling shaft. Any help appreciated, thanks
@coffeetechph2 жыл бұрын
Watch this video and jump at 23:00 so you can see how ready position looks like. kzbin.info/www/bejne/rYO4gGycfq6Uhtk
@Nealf20022 жыл бұрын
@@coffeetechph hi it’s grinding and jamming when at the top of the spool. Do you give technical advice? I would love to chat or email offline. Thanks!
@coffeetechph2 жыл бұрын
@@Nealf2002 kindly message us on our fb page. facebook.com/Coffeetech.ph/
@rizalnunostv1563 жыл бұрын
Hi. I've got the same error 6 problem on my old Jura Z5. what is the specific name of the micro switch sensor? where can I order it? thanks a lot.
@coffeetechph3 жыл бұрын
I just bought that micro switch on electronic shop. Try to replace your ceramic valve and look for micro switch.
@chanlumanogtv2493 жыл бұрын
Keep it up bro God bless po
@nabilfreeman3 жыл бұрын
Btw, to other owners watching, once you have removed the sides and top parts it is possible to remove both the grinder and the brew unit without touching the electrics. I just needed to disconnect the pump’s water tube and you can tilt the grinder out slightly to pull all the bits out
@nabilfreeman3 жыл бұрын
Thank you so much for making this!!! Last time I disassembled 6 months ago I couldn’t find a full guide 👏
@coffeetechph3 жыл бұрын
Hi, im editing a video how to assemble this ena 9. Hope i can upload by next week.