ArabiaBayRidge

Пікірлер

@user-pp4uy7wf7f 23 күн бұрын

I didn't know you use Teflon tape

@ArabiaBayRidge 23 күн бұрын

You don’t have too but Teflon really helps when you take it apart a year later. Without the corrosion on the threads are so bad you can not unscrew it

@istra70 25 күн бұрын

I also displaced rubber plug in carburetor when accidentally created pressure in fuel tank... Easy fix.

@istra70 25 күн бұрын

My 3.5 runs perfectly ! And i used to drive it hard all day long .... The only time i was careful was at the beginning when I was running it in....

@Dungeonbeatz 28 күн бұрын

Hank is that you 🤣

@MyUnquenchableThirst 29 күн бұрын

Thanks for the tips!

@ArabiaBayRidge Ай бұрын

It does not have a size listed on it or it has worn off I think I emailed turbo and bought the one they recommended

@nswave Ай бұрын

what size turbo swing i have same motor

@Stripe12 Ай бұрын

So did it make a difference??

@ArabiaBayRidge Ай бұрын

Yes I changed the fitting and trimmed the vent plug no problems in years now

@ryanharrod1155 Ай бұрын

You got a video on how you installed that steel guide?

@ArabiaBayRidge Ай бұрын

I don’t. 1/2 inch aluminum rod from Lowe’s welded to a 1/8 inch aluminum plate hand bent the rod cut to fit with a jig saw bolted to skeg and attached to shaft with hose clamps. Has never moved

@ArabiaBayRidge 2 ай бұрын

Nothing to do with data the transducer throws a lot of spray on my outboard without

@colin5230 2 ай бұрын

What is the point of these? Does it do anything for ypur data its collecting? Or is it just to prevent it from spraying?

@cd1168 9 ай бұрын

You didn’t show shit

@pokeygalaxy 9 ай бұрын

this video sucks

@jameslakes5019 10 ай бұрын

As much cost should out perform great out box😊

@edwincordero1810 10 ай бұрын

Thanks I have that problem yesterday with my sea hunt

@JuanHernandez-jc6re Жыл бұрын

What shaft length you recommend ?

@steve8803 10 ай бұрын

@JuanHernandez-jc6re it depends on the boat and the mount height. You want the propeller to be about 12" in the water.

@gmoneyfilmss Жыл бұрын

i just got a trolling motor for my john boat and have a question is there a right and wrong for mounting your motor rear or bow?? from what i’ve researched what motor you have determines your mounting position, but am curious if there’s a reason other than that?? thank you!!

@SpinachMinich Жыл бұрын

You takin dale, bill, and boomhauer out later?

@ArabiaBayRidge Жыл бұрын

I now have about 220 hrs on the unit. No issues at I change the fluid every year just because it is easy I did have the lower repainted because it was peeling

@dillongoble7483 Жыл бұрын

Hey I'm here seeking the same answers did you ever have any problems with the lower unit? I have a lot of metal shavings in mine.

@ArabiaBayRidge Жыл бұрын

I now have about 670 hrs total on the boat and I think about 220 hrs or so on the new lower unit No problems at at. I change the fluid every year just because it is easy. I now have a power tech prop and the gear shifting is a lot quieter than a solas prop

@JamesJoseph-te3jm Жыл бұрын

I was getting so pissed, how do they expect you to remove it without doing this! there is absolutely no room to do it, glad you posted this, i would have been screwed, thank you.

@WillInWestPalm Жыл бұрын

yamahaw

@ArabiaBayRidge Жыл бұрын

That’s right … you wanna fight about it 🤣 lol. I got a southern draw

@TheFilthyOX Жыл бұрын

Thanks for this video. My tiller is shearing the bolts on the top gearbox and broke the top brace as well. Now I am thinking nothing is holding the bottom of the gearbox as there are no heads on those bolts or they fell out. Time to start investigating.

@joshuaculick7767 Жыл бұрын

What battery to use on it ?

@josephcampise6441 Жыл бұрын

I use a 12 deep cycle marine battery on mine

@josephcampise6441 Жыл бұрын

12v*

@ArabiaBayRidge Жыл бұрын

12 volt deep cycle. I have used a agm 27 series and now have a lithium 60ah all 12 volt for this model

@zachgray319 Жыл бұрын

Is that the tranducer 3m plate? How it holding up?

@ArabiaBayRidge Жыл бұрын

Yes the splash plate and the 3m plastic mount are still doing great

@ArabiaBayRidge 2 ай бұрын

3m mount is still doing great!!

@Htownrule Жыл бұрын

I have a way older version on my 12ft Jon Boat it’s the Motorguide Brute 750 45lbs trust version.. I was wondering has this one held up well for you and do you recommend me upgrading?

@miketexas4549 Жыл бұрын

Hank Hill?

@ArabiaBayRidge Жыл бұрын

No I’m his smarter cousin

@jasonhollis8700 Жыл бұрын

This was a smart $20 fix instead of a $200 prop puller. Thank you for posting this video.

@matt4887 Жыл бұрын

Thanks very helpful

@jasonwade6184 Жыл бұрын

I've lost the little rubber stopper What is its purpose

@ndk8111 Жыл бұрын

Question - when you removed your prop did the forward thrust hub came off easily (the yellow round plate the prop sits on)? My 60hp mercury 2022 prop came off but the hub seems like ceased to the shaft - it should be coming off easily, no? I too was thinking of pulling like you instead of trying to bang it. So if you could provide additional details I would appreciate. Also, did you have to use penetrating oil / liquid wrench at all?

@ArabiaBayRidge Жыл бұрын

I did not use oil. And my thrust washer was loose I would suggest a wire wheel on a drill clean the shaft good soak with penetrating oil and tap lightly

@travonnjohnson5606 Жыл бұрын

Thank you!!! This is exactly what is wrong with mine. I'm new to this, so I would have never noticed. This helps a lot!!!

@ahmedbatt366 2 жыл бұрын

Hi, how is the result after installing the shield so far? I have the same issue with the same transducer.

@ArabiaBayRidge 2 жыл бұрын

It works! Water no longer hits my outboard or sprays high I can still see water spray but this greatly reduced my problem I would buy it again

@JohnSmith-xq6cv 2 жыл бұрын

For sale?

@JohnSmith-xq6cv 2 жыл бұрын

Is it easy without row markers?

@jimfrits334 2 жыл бұрын

Thanks, you just saved me a lot of trouble. I have three seals on their way to me as I type this.

@cameronbuck3345 Жыл бұрын

Where did you order the seals from?

@michaelsolis2674 2 жыл бұрын

Yep needed that...

@ezzyeggy 2 жыл бұрын

Do you have to loosen the motor or front case to get it off?

@ArabiaBayRidge 2 жыл бұрын

You do not have to move the motor or front differential The prop will slide back enough once you remove the roll pin

@jimquantic 2 жыл бұрын

This IS superior to the way I just did it, it really is because it pulls it true--straight out. But my method worked and without the rigging. I used a rubber hammer--I know, sounds bad, but bear with me. I "tapped" pretty gently as I rotated the prop, each wrap is of course off-set, so as I said, not ideal. But after maybe 50 or less raps, I saw it break free from the seal it had made, then I pulled it straight off.

@kippiemoore7439 2 жыл бұрын

Now how do you put it back together?

@slugzgaming5158 3 жыл бұрын

Horrible audio no idea what u said

@scottm6449 3 жыл бұрын

Nice job explaining the gearbox removal. Had similar seal leak with the pto shaft on my Tarter 5 ft. tiller. Used 00 grease and 85-140 gear oil and it worked until the seal popped out. Removed the pto shaft from the tractor tapped the seal back in and it now does not leak. Please check your your gearcase filler/breather fitting to be certain it is open. Let my tiller sit for a year and when I checked the chaincase fill level plug it was still under a great deal of pressure and it shot out some gear oil! That much pressure could cause a leak or pop a seal maybe, Thanks!

@robertleibold4502 3 жыл бұрын

I am having a heck of a time right now getting that bottom piece on the plunger to unscrew All rusted up and now I have it in my electrolysis bucket. Most likely will have to order a new plunger too... :(