Wow at the end of this he goes to say that it DIDNT WORK stating that it says it's bad battery. A friend of my tried this just to indicate out that it completely killed his battery. Never add vinegar to a lead acid battery it will only damage the battery cells and shorten the life of your battery. ONLY ADD DISTILLED WATER

How’s the snappers holding up 10 years later?

Thk u

Thank you for the video. My weedeater had the lines incorrect. I honestly don't know how it happened. I noticed the primer bulb would not fill, and air was being pumped in the tank. I switched the gas lines and bamm I have power.

Nice.

Please explain to me the four Cycles are that you're talking about

Cycle 4 cycle.how about 2 stroke?????

You had to remove the deck, correct?

I always do want to work on a transmission.

Old School rebuilt a couple hundred of those. Had a shop 38 years. PS- My Dad's identical twin designed all the Lawnboys. Me and Dad met Steve Ariens the Guy That Dreamed That Shit Up.

Hey what did u do about the ground wire

My g the gas line is the short one there done 6 minutes video answered in 3 seconds in the comments

Welcome back brother. I hope all is well and thanks for sharing

Excellent video/ Thanks so much !

Great video Sir, thank you for making it - very helpful.

Can cut off voltage be adjusted ?

Do you still have your Jump box - I pick-up a used one, need to see/ know what the wire connections are. Mainly to the battery & the switch. Can you share?

2 cycle.

Experience has told me TWO ISSUES RELATED TO your video: 1) Too close to gearbox and you will have trouble installing new belt. 2) Looking at your grease leak deposits, shaft nut for clutch likely loose and key at risk; getting properly tightened MAY cure leak at seal without seal replace. Can be a real challenging bear if woodruff shears flush, and requires patience and special tools to remove old woodruff. I.E I SUSPECT THE GREASE LEAK IS THE REASON FOR THE CLUTCH SLIPPAGE. i WENT THRU two new DRIVEN DISK HUBS (that clutch bolts to) before I got shaft properly torqued to prevent coming loose again. GOOD LUCK.

You don’t show where to connect each line, which one is closer to the primer valve?

Thanks so much! Clear, concise and informative!

Jeez, I don't need THAT much foreplay!

Gracias por ponerlo en Espanol

Great video with clear instructions. Keep making your videos. Don't worry about those negative people. There will always be bitter people who can't resist expressing their opinions of negativity (constructive criticism) to anything they interact with in their negative lifestyle. Kinda sad really, that they live with so much negativity that it overflows onto others. Anyways, great video and can't wait for your next one. Take care.

Please show me how to replace pull rope

Wow talk about dragging it out as long as you possibly can, very helpful tho. Was that an actual four stroke edger, or two?

Wow...i researched some videos on how to select the fuel line yours is the most simple..thanks a lot

Dont do this hes so wrong use 4 diods make sure they are rated for the volt and amp either way 4 diods will make a full bridge rectifier if done right. There are plenty of videos on the you tube on how to do it its so easy

I take it there is a battery in the thermostat itself?

Great tip man, fixed my problem

I just can't see how you could insert a fuel filter to back up in there from the inside out. Makes me feel like crying like I won't be able to fix it easily

The line on my Honda weed eater disintegrated that has the fuel filter at the end of it to can I just get tubing for that or do I have to use that kit that costs about $30?

It's amazing how evil people can be on the comments in KZbin makes me embarrassed to be English speaking. Why they would do that to people that are just trying to help anyway.

Thanks for the informative video. Interesting how you custom set up the circuit breaker?

Skip to 1:38

Is it krylon banner red that matches?

Hi. Very interesting video. I am from Ukraine. With numerous electricity outages having solar shed is 'bare-minimum'/ I have APC Smart UPS 1000 for my experiments... + 2 old solar Panels. Just few questions: 1/ Do you have external AC connected to the APC ? or you have fully "Stand-alone" setup? meaning that APC is operating always on battery mode 2/ On the video you have parallel wires from Batteries to charger and to the APC. Can we use standard connector for External Batteries for this? APC Smart UPS 1000 has build-in External Battery connector (for additional 24 V bank) I want to configure setup with minimum changes...

How does this help Magic jack?

Very helpful. Thank you

Thank you. Good video and helpful.

Remember this the fuel is pulled thru the carb with vacuum made by pressing the purg ball and fuel return to tank

Just picked one up for $100! SR 1433, made in 97-98

I’m sorry……But, those 5 extra minutes paid Dividends. Thanks for the video. I have subscribed to your channel .

Not the fuel line with the filter, but the return line. Some return lines have a connector on the end withing the fuel tank. Is the connector required? Thanks

This guy was a dick, waisted 7min of my life. I’ll just plug the line into one 50% chance. There

How to make a 10sec video into a bunch of worthless words

Thank-you

whos on first, what line is the return line, wait port. cover your right eye and squeeze bulb, thats the port line. Sir please identify the gas line that has the filter, then identify the return line/port line, do u see how confusing that is. Is one bigger? is one on the leftside or right side top port. Very confusing and way too long.

I crushed the diode didnt know what it was lol my mower still goes but battery dies now even when off

What size allen key did it call for ?